- 19 12月, 2013 7 次提交
-
-
由 Du, ChangbinX 提交于
From 7e827a0d300e084f74c65122baa5e3193f9a7f18 Mon Sep 17 00:00:00 2001 From: "Du, Changbin" <changbinx.du@intel.com> Date: Mon, 16 Dec 2013 20:32:13 +0800 Subject: [PATCH] usb/gadget: should use u16 type variable to store MaxPower The MaxPower field is of u16 type. So using u8 type variable can break data (high byte lost). Signed-off-by: NDu, Changbin <changbinx.du@intel.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 George Cherian 提交于
This adds omap control module support for USBSS in AM437x SoC. Update DT binding information to reflect these changes. Acked-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NGeorge Cherian <george.cherian@ti.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Rashika Kheria 提交于
Include header file drivers/usb/phy/am35x-phy-control.h in phy/phy-am335x-control.c because function am335x_get_phy_control() has its prototype declaration in drivers/usb/phy/am35x-phy-control.h. Also, remove definition of structure phy_control because it is already defined in the included header. This eliminates the following warning in phy/phy-am335x-control.c: drivers/usb/phy/phy-am335x-control.c:114:21: warning: no previous prototype for ‘am335x_get_phy_control’ [-Wmissing-prototypes] Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com> Reviewed-by: NJosh Triplett <josh@joshtriplett.org> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Rashika Kheria 提交于
Include appropriate header file drivers/usb/gadget/configfs.h in gadget/configfs.c because function unregister_gadget_item() has its prototype declaration in gadget/configfs.h. This eliminates the following warning in gadget/configfs.c: drivers/usb/gadget/configfs.c:994:6: warning: no previous prototype for ‘unregister_gadget_item’ [-Wmissing-prototypes] Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com> Reviewed-by: NJosh Triplett <josh@joshtriplett.org> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Heikki Krogerus 提交于
The reset_gpio member of the usb_phy_gen_xceiv_platform_data structure needs the have negative value or phy-generic's probe will fail unless DT is used. 0 is a valid gpio number. This fixes an issue where phy-generic fails to probe with message: "usb_phy_gen_xceiv.0: Error requesting RESET GPIO 0". Cc: <stable@vger.kernel.org> Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 George Cherian 提交于
USB remote wakeup using PHY wakeup is supported only in standby mode. Enabling the PHY_WKUP will break DS0 mode of system suspend. If the same is enabled while entering DS0, AM33xx never stays in DS0, it returns immediately from DS0. By default make the PHY wakeup disabled, using sysfs entry enable the same manually to get the remote wakeup working from standby. echo enabled > /sys/bus/platform/device/<usb phy id>/power/wakeup This will enable the PHY wakeup while going to standby. PHY wakeup feature is required to wakeup the system from standby state. Since AM33xx has a bug in which PHY wakeup should not be enabled while entering DS0, disable the same by default. A user wishing to use USB wakeup from standby mode need to enable the same using the sysfs entries. Also remove am335x_phy_runtime_(suspend/resume) this driver doesnot really enable/disable the clocks to the PHY. Add am335x_phy_(suspend/resume) and use the same for enabling the PHY_WKUP. Signed-off-by: NGeorge Cherian <george.cherian@ti.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Felipe Balbi 提交于
Linux 3.13-rc4 * tag 'v3.13-rc4': (1001 commits) Linux 3.13-rc4 null_blk: mem garbage on NUMA systems during init radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh() Revert "selinux: consider filesystem subtype in policies" igb: Fix for issue where values could be too high for udelay function. i40e: fix null dereference ARM: fix asm/memory.h build error dm array: fix a reference counting bug in shadow_ablock dm space map: disallow decrementing a reference count below zero mm: memcg: do not allow task about to OOM kill to bypass the limit mm: memcg: fix race condition between memcg teardown and swapin thp: move preallocated PTE page table on move_huge_pmd() mfd/rtc: s5m: fix register updating by adding regmap for RTC rtc: s5m: enable IRQ wake during suspend rtc: s5m: limit endless loop waiting for register update rtc: s5m: fix unsuccesful IRQ request during probe drivers/rtc/rtc-s5m.c: fix info->rtc assignment include/linux/kernel.h: make might_fault() a nop for !MMU drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap procfs: also fix proc_reg_get_unmapped_area() for !MMU case ... Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
- 18 12月, 2013 12 次提交
-
-
由 Jingoo Han 提交于
Make local symbols static in order to fix the following sparse warnings. drivers/usb/gadget/f_sourcesink.c:205:34: warning: symbol 'ss_source_comp_desc' was not declared. Should it be static? drivers/usb/gadget/f_sourcesink.c:222:34: warning: symbol 'ss_sink_comp_desc' was not declared. Should it be static? drivers/usb/gadget/f_sourcesink.c:240:34: warning: symbol 'ss_iso_source_comp_desc' was not declared. Should it be static? drivers/usb/gadget/f_sourcesink.c:258:34: warning: symbol 'ss_iso_sink_comp_desc' was not declared. Should it be static? Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Jingoo Han 提交于
Make local symbol static in order to fix the following sparse warning. drivers/usb/gadget/f_serial.c:357:21: warning: symbol 'gser_alloc' was not declared. Should it be static? Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Jingoo Han 提交于
Make local symbol static in order to fix the following sparse warning. drivers/usb/gadget/f_phonet.c:692:21: warning: symbol 'phonet_alloc' was not declared. Should it be static? Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Jingoo Han 提交于
Make local symbol static in order to fix the following sparse warning. drivers/usb/gadget/f_obex.c:502:21: warning: symbol 'obex_alloc' was not declared. Should it be static? Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Jingoo Han 提交于
Make local symbol static in order to fix the following sparse warning. drivers/usb/gadget/f_ncm.c:1389:21: warning: symbol 'ncm_alloc' was not declared. Should it be static? Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Jingoo Han 提交于
Use NULL instead of 0 when returning pointer, to fix the following sparse warnings. drivers/usb/gadget/f_mass_storage.c:3114:60: warning: Using plain integer as NULL pointer drivers/usb/gadget/f_mass_storage.c:3114:63: warning: Using plain integer as NULL pointer Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Jingoo Han 提交于
Make local symbols static in order to fix the following sparse warnings. drivers/usb/gadget/f_loopback.c:123:34: warning: symbol 'ss_loop_source_comp_desc' was not declared. Should it be static? drivers/usb/gadget/f_loopback.c:139:34: warning: symbol 'ss_loop_sink_comp_desc' was not declared. Should it be static? Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Lee Jones 提交于
static checker warning: "drivers/usb/musb/ux500_dma.c:335 ux500_dma_controller_start() error: potential NULL dereference 'param_array'." Acked-by: NLinus Walleij <linus.walleij@linaro.org> Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NLee Jones <lee.jones@linaro.org> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Jingoo Han 提交于
'usba_gadget_template' is used only in this file. Thus, make 'usba_gadget_template' static, in order to fix the following sparse warning. warning: symbol 'usba_gadget_template' was not declared. Should it be static? Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Jingoo Han 提交于
Use devm_*() functions to make cleanup paths simpler. Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Andrzej Pietrasiewicz 提交于
In the nokia gadget some USB functions (obex 1 and 2, phonet) are optional. If at the start of nokia_bind_config e.g. fi_phonet is an error pointer, which can happen because we don't fail the bind process if usb_get_function_instance() fails for fi_phonet, then f_phonet is NULL, and phonet_stat = usb_add_function(c, f_phonet); is never called and phonet_stat remains 0. If, in these circumstances, we hit the err_conf label then !phonet_stat evaluates to true and we try usb_remove_function() with its second parameter being f_phonet which is NULL and it causes NULL pointer dereference. This patch changes the initial values of (obex1|obex2|phonet)_stat to a nonzero value so that if the err_conf label is hit while the respective functions have not been acquired the usb_remove_function() is not called for those functions. Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Robert Baldyga 提交于
This patch adds "maxpacket_limit" to struct usb_ep. This field contains maximum value of maxpacket supported by driver, and is set in driver probe. This value should be used by autoconfig() function, because value of field "maxpacket" is set to value from endpoint descriptor when endpoint becomes enabled. So when autoconfig() function will be called again for this endpoint, "maxpacket" value will contain wMaxPacketSize from descriptior instead of maximum packet size for this endpoint. For this reason this patch adds new field "maxpacket_limit" which contains value of maximum packet size (which defines maximum endpoint capabilities). This value is used in ep_matches() function used by autoconfig(). Value of "maxpacket_limit" should be set in UDC driver probe function, using usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function set choosen value to both "maxpacket_limit" and "maxpacket" fields. This patch modifies UDC drivers by adding support for maxpacket_limit. Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
- 16 12月, 2013 8 次提交
-
-
由 Linus Torvalds 提交于
-
由 Matias Bjorling 提交于
For NUMA systems, initializing the blk-mq layer and using per node hctx. We initialize submit queues to 1, while blk-mq nr_hw_queues is initialized to the number of NUMA nodes. This makes the null_init_hctx function overwrite memory outside of what it allocated. In my case it lead to writing garbage into struct request_queue's mq_map. Signed-off-by: NMatias Bjorling <m@bjorling.me> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Sergey Senozhatsky 提交于
Since commit ec39f64b ("drm/radeon/dpm: Convert to use devm_hwmon_register_with_groups") radeon_hwmon_init() is using hwmon_device_register_with_groups(), which sets `rdev' as a device private driver_data, while hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh() are still waiting for `drm_device'. Fix them by using dev_get_drvdata(), in order to avoid this oops: BUG: unable to handle kernel paging request at 0000000000001e28 IP: [<ffffffffa02ae8b4>] hwmon_attributes_visible+0x18/0x3d [radeon] PGD 15057e067 PUD 151a8e067 PMD 0 Oops: 0000 [#1] PREEMPT SMP Call Trace: internal_create_group+0x114/0x1d9 sysfs_create_group+0xe/0x10 sysfs_create_groups+0x22/0x5f device_add+0x34f/0x501 device_register+0x15/0x18 hwmon_device_register_with_groups+0xb5/0xed radeon_hwmon_init+0x56/0x7c [radeon] radeon_pm_init+0x134/0x7e5 [radeon] radeon_modeset_init+0x75f/0x8ed [radeon] radeon_driver_load_kms+0xc6/0x187 [radeon] drm_dev_register+0xf9/0x1b4 [drm] drm_get_pci_dev+0x98/0x129 [drm] radeon_pci_probe+0xa3/0xac [radeon] pci_device_probe+0x6e/0xcf driver_probe_device+0x98/0x1c4 __driver_attach+0x5c/0x7e bus_for_each_dev+0x7b/0x85 driver_attach+0x19/0x1b bus_add_driver+0x104/0x1ce driver_register+0x89/0xc5 __pci_register_driver+0x58/0x5b drm_pci_init+0x86/0xea [drm] radeon_init+0x97/0x1000 [radeon] do_one_initcall+0x7f/0x117 load_module+0x1583/0x1bb4 SyS_init_module+0xa0/0xaf Signed-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Alexander Deucher <Alexander.Deucher@amd.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: 1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't figure out why it breaks things. 2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it was basically doing "x == x", from Dave Jones. 3) Freescale FEC driver was DMA mapping the wrong number of bytes, from Sebastian Siewior. 4) Blackhole and prohibit routes in ipv6 were not doing the right thing because their ->input and ->output methods were not being assigned correctly. Now they behave properly like their ipv4 counterparts. From Kamala R. 5) Several drivers advertise the NETIF_F_FRAGLIST capability, but really do not support this feature and will send garbage packets if fed fraglist SKBs. From Eric Dumazet. 6) Fix long standing user triggerable BUG_ON over loopback in RDS protocol stack, from Venkat Venkatsubra. 7) Several not so common code paths can potentially try to invoke packet scheduler actions that might be NULL without checking. Shore things up by either 1) defining a method as mandatory and erroring on registration if that method is NULL 2) defininig a method as optional and the registration function hooks up a default implementation when NULL is seen. From Jamal Hadi Salim. 8) Fix fragment detection in xen-natback driver, from Paul Durrant. 9) Kill dangling enter_memory_pressure method in cg_proto ops, from Eric W Biederman. 10) SKBs that traverse namespaces should have their local_df cleared, from Hannes Frederic Sowa. 11) IOCB file position is not being updated by macvtap_aio_read() and tun_chr_aio_read(). From Zhi Yong Wu. 12) Don't free virtio_net netdev before releasing all of the NAPI instances. From Andrey Vagin. 13) Procfs entry leak in xt_hashlimit, from Sergey Popovich. 14) IPv6 routes that are no cached routes should not count against the garbage collection limits. We had this almost right, but were missing handling addrconf generated routes properly. From Hannes Frederic Sowa. 15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL route info when they are called, from Stefan Tomanek. 16) TUN and MACVTAP have had truncated packet signalling for some time, fix from Jason Wang. 17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet. 18) xen-netback does not interpret the NAPI budget properly for TX work, fix from Paul Durrant. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits) igb: Fix for issue where values could be too high for udelay function. i40e: fix null dereference xen-netback: fix gso_prefix check net: make neigh_priv_len in struct net_device 16bit instead of 8bit drivers: net: cpsw: fix for cpsw crash when build as modules xen-netback: napi: don't prematurely request a tx event xen-netback: napi: fix abuse of budget sch_tbf: use do_div() for 64-bit divide udp: ipv4: must add synchronization in udp_sk_rx_dst_set() net:fec: remove duplicate lines in comment about errata ERR006358 Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature" 8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature xen-netback: make sure skb linear area covers checksum field net: smc91x: Fix device tree based configuration so it's usable udp: ipv4: fix potential use after free in udp_v4_early_demux() macvtap: signal truncated packets tun: unbreak truncated packet signalling net: sched: htb: fix the calculation of quantum net: sched: tbf: fix the calculation of max_size micrel: add support for KSZ8041RNLI ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull x86 fixes from Peter Anvin: "This is a pretty small batch: The biggest single change is to stop using EFI time services on 32-bit platforms. This matches our current behavior on 64-bit platforms as we already had ruled them out there as being too unreliable. Turns out that affects 32-bit platforms, too. One NULL pointer fix for SGI UV. Two minor build fixes, one of which only affects icc and the other which affects icc and future versions or nonstandard default settings of gcc" * 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86, efi: Don't use (U)EFI time services on 32 bit x86, build, icc: Remove uninitialized_var() from compiler-intel.h x86/UV: Fix NULL pointer dereference in uv_flush_tlb_others() if the 'nobau' boot option is used x86, build: Pass in additional -mno-mmx, -mno-sse options
-
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci由 Linus Torvalds 提交于
Pull PCI updates from Bjorn Helgaas: "PCI device hotplug - Move device_del() from pci_stop_dev() to pci_destroy_dev() (Rafael Wysocki) Host bridge drivers - Update maintainers for DesignWare, i.MX6, Armada, R-Car (Bjorn Helgaas) - mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin (Jason Gunthorpe) Miscellaneous - Avoid unnecessary CPU switch when calling .probe() (Alexander Duyck) - Revert "workqueue: allow work_on_cpu() to be called recursively" (Bjorn Helgaas) - Disable Bus Master only on kexec reboot (Khalid Aziz) - Omit PCI ID macro strings to shorten quirk names for LTO (Michal Marek)" * tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: MAINTAINERS: Add DesignWare, i.MX6, Armada, R-Car PCI host maintainers PCI: Disable Bus Master only on kexec reboot PCI: mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin PCI: Omit PCI ID macro strings to shorten quirk names PCI: Move device_del() from pci_stop_dev() to pci_destroy_dev() Revert "workqueue: allow work_on_cpu() to be called recursively" PCI: Avoid unnecessary CPU switch when calling driver .probe() method
-
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security由 Linus Torvalds 提交于
Pull SELinux fixes from James Morris. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: selinux: process labeled IPsec TCP SYN-ACK packets properly in selinux_ip_postroute() selinux: look for IPsec labels on both inbound and outbound packets selinux: handle TCP SYN-ACK packets correctly in selinux_ip_postroute() selinux: handle TCP SYN-ACK packets correctly in selinux_ip_output() selinux: fix possible memory leak
-
由 Linus Torvalds 提交于
This reverts commit 102aefdd. Tom London reports that it causes sync() to hang on Fedora rawhide: https://bugzilla.redhat.com/show_bug.cgi?id=1033965 and Josh Boyer bisected it down to this commit. Reverting the commit in the rawhide kernel fixes the problem. Eric Paris root-caused it to incorrect subtype matching in that commit breaking fuse, and has a tentative patch, but by now we're better off retrying this in 3.14 rather than playing with it any more. Reported-by: NTom London <selinux@gmail.com> Bisected-by: NJosh Boyer <jwboyer@fedoraproject.org> Acked-by: NEric Paris <eparis@redhat.com> Cc: James Morris <jmorris@namei.org> Cc: Anand Avati <avati@redhat.com> Cc: Paul Moore <paul@paul-moore.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 15 12月, 2013 3 次提交
-
-
由 Carolyn Wyborny 提交于
This patch changes the igb_phy_has_link function to check the value of the parameter before deciding to use udelay or mdelay in order to be sure that the value is not too high for udelay function. CC: stable kernel <stable@vger.kernel.org> # 3.9+ Signed-off-by: NSunil K Pandey <sunil.k.pandey@intel.com> Signed-off-by: NKevin B Smith <kevin.b.smith@intel.com> Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesse Brandeburg 提交于
If the vsi->tx_rings structure is NULL we don't want to panic. Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10 Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp由 Linus Torvalds 提交于
Pull EDAC fix from Borislav Petkov: "Silence a compiler warning in sb_edac" * tag 'edac_fixes_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: sb_edac: Shut up compiler warning when EDAC_DEBUG is enabled
-
- 14 12月, 2013 10 次提交
-
-
git://ftp.arm.linux.org.uk/~rmk/linux-arm由 Linus Torvalds 提交于
Pull ARM fixes from Russell King: "This resolves some further issues with the dma mask changes on ARM which have been found by TI and others, and also some corner cases with the updates to the virtual to physical address translations. Konstantin also found some problems with the unwinder, which now performs tighter verification that the stack is valid while unwinding" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: fix asm/memory.h build error ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed ARM: 7913/1: fix framepointer check in unwind_frame ARM: 7912/1: check stack pointer in get_wchan ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init() ARM: 7908/1: mm: Fix the arm_dma_limit calculation ARM: another fix for the DMA mapping checks
-
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc由 Linus Torvalds 提交于
Pull ARC fixes from Vineet Gupta: "These are couple of weeks old already, but I just couldn't get them to you earlier. - couple of fixes for recently added perf code - build time extable sort" * tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: ARC: [perf] Fix a few thinkos ARC: Add guard macro to uapi/asm/unistd.h ARC: extable: Enable sorting at build time
-
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm由 Linus Torvalds 提交于
Pull device mapper fixes from Mike Snitzer: "A set of device-mapper fixes for 3.13. A fix for possible memory corruption during DM table load, fix a possible leak of snapshot space in case of a crash, fix a possible deadlock due to a shared workqueue in the delay target, fix to initialize read-only module parameters that are used to export metrics for dm stats and dm bufio. Quite a few stable fixes were identified for both the thin- provisioning and caching targets as a result of increased regression testing using the device-mapper-test-suite (dmts). The most notable of these are the reference counting fixes for the space map btree that is used by the dm-array interface -- without these the dm-cache metadata will leak, resulting in dm-cache devices running out of metadata blocks. Also, some important fixes related to the thin-provisioning target's transition to read-only mode on error" * tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm array: fix a reference counting bug in shadow_ablock dm space map: disallow decrementing a reference count below zero dm stats: initialize read-only module parameter dm bufio: initialize read-only module parameters dm cache: actually resize cache dm cache: update Documentation for invalidate_cblocks's range syntax dm cache policy mq: fix promotions to occur as expected dm thin: allow pool in read-only mode to transition to read-write mode dm thin: re-establish read-only state when switching to fail mode dm thin: always fallback the pool mode if commit fails dm thin: switch to read-only mode if metadata space is exhausted dm thin: switch to read only mode if a mapping insert fails dm space map metadata: return on failure in sm_metadata_new_block dm table: fail dm_table_create on dm_round_up overflow dm snapshot: avoid snapshot space leak on crash dm delay: fix a possible deadlock due to shared workqueue
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid由 Linus Torvalds 提交于
Pull HID fixes from Jiri Kosina: - Genius Gx Imperator Keyboard regression fix (missing break in case), by Ben Hutchings - duplicate sysfs entry error fix for hid-sensor-hub driver, by Srinivas Pandruvada * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: hid-sensor-hub: fix duplicate sysfs entry error HID: kye: Fix missing break in kye_report_fixup()
-
由 Russell King 提交于
Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is not defined: In file included from arch/arm/include/asm/page.h:163:0, from include/linux/mm_types.h:16, from include/linux/sched.h:24, from arch/arm/kernel/asm-offsets.c:13: arch/arm/include/asm/memory.h: In function '__virt_to_phys': arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function) arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in arch/arm/include/asm/memory.h: In function '__phys_to_virt': arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function) Fixes: ca5a45c0 ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions") Tested-By: NJason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator由 Linus Torvalds 提交于
Pull regulator fixes from Mark Brown: "A small set of driver fixes plus one larger core change which changes the way we check to see if we're using DT so that there aren't any races between deciding we're using DT and the regulator subsystem noticing. This makes the new support for substituting a dummy regulator and optional regulators work a lot better on DT systems since it ensures that we don't trigger probe deferral when we shouldn't which was causing bugs in clients" * tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: regulator: pfuze100: allow misprogrammed ID regulator: pfuze100: Fix address of FABID regulator: as3722: set the correct current limit regulator: core: Check for DT every time we check full constraints regulator: core: Replace checks of have_full_constraints with a function
-
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap由 Linus Torvalds 提交于
Pull regmap fixes from Mark Brown: "Two small changes to fix some error handling and checking (both of which would be quite serious if the errors trigger) plus a trivial documentation fix" * tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: regmap: use IS_ERR() to check clk_get() results regmap: make sure we unlock on failure in regmap_bulk_write regmap: trivial comment fix (copy'n'paste error)
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux由 Linus Torvalds 提交于
Pull i2c fixes from Wolfram Sang: "Here are two simple but wanted fixes for the i2c subsystem" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: imx: Check the return value from clk_prepare_enable() i2c: mux: Inherit retry count and timeout from parent for muxed bus
-
git://git.infradead.org/linux-mtd由 Linus Torvalds 提交于
Pull MTD fixes from Brian Norris: "Two MTD fixes, for the pxa3xx-nand driver: - This driver was not ready to fully Armada 370 NAND, with particularly notable problems seen on flash with 2KB page sizes. This "compatible" entry really should have been held back until 3.14 or later. - Fix a bug seen in rare cases on the error path of a failed probe attempt, where we free unallocated DMA resources" * tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd: mtd: nand: pxa3xx: Use info->use_dma to release DMA resources Partially revert "mtd: nand: pxa3xx: Introduce 'marvell,armada370-nand' compatible string"
-
git://git.infradead.org/users/vkoul/slave-dma由 Linus Torvalds 提交于
Pull slave-dmaengine fixes from Vinod Koul: "Here is the common fixes PULL for dmaengine. Dan has been working on fixing the build issues in bunch of drivers. Here we have one fixing s3c24xx-dma, along with fix from Russell on pl08x. Also we have Kuninori rcar dma fixes. The s3c24xx-dma which was added in last merge window missed updates to usage of DMA_COMPLETE so converting the last driver" * 'fixes' of git://git.infradead.org/users/vkoul/slave-dma: dma: fix build breakage in s3c24xx-dma Fix pl08x warnings rcar-hpbdma: initialise plane information when halted rcar-hpbdma: fixup channel busy check for double plane rcar-hpbdma: add max transfer size dma: mmp_pdma: add missing platform_set_drvdata() in mmp_pdma_probe() dmaengine: s3c24xx-dma: use DMA_COMPLETE for dma completion status
-