Use SET_RUNTIME_PM_OPS macro to set runtime functions.
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The omap_i2c_remove function may not be needed after
device exit so the memory could be freed.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

On a board with OMAP3 processor and TWL4030 Power management,
we need to talk to the TWL4030 during late suspend but cannot
because the I2C interrupt is disabled (as late suspend disables
interrupt).

e.g. I get messages like:

[   62.161102] musb-omap2430 musb-omap2430: LATE power domain suspend
[   63.167205] omap_i2c omap_i2c.1: controller timed out
[   63.183044] twl: i2c_read failed to transfer all messages
[   64.182861] omap_i2c omap_i2c.1: controller timed out
[   64.198455] twl: i2c_write failed to transfer all messages
[   65.198455] omap_i2c omap_i2c.1: controller timed out
[   65.203765] twl: i2c_write failed to transfer all messages

The stack shows omap2430_runtime_suspend calling twl4030_set_suspend
which tries to power-down the USB PHY (twl4030_phy_suspend ->
twl4030_phy_power -> __twl4030_phy_power which as a nice WARN_ON
that helps).

Then we get the same in resume:

[   69.603912] musb-omap2430 musb-omap2430: EARLY power domain resume
[   70.610473] omap_i2c omap_i2c.1: controller timed out
[   70.626129] twl: i2c_write failed to transfer all messages
etc.

So don't disable interrupts for I2C.
Acked-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The section number in the recent errata document has changed.
Rename the erratum 1p153 to the unique id i462 instead, so that
it is easier to reference. Also change the function name and comments
to reflect the same.

Cc: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Currently in the 1.153 errata handling, while waiting for transmitter
underflow, if NACK is got the XUDF(Transmit underflow) flag is also set.
Fix this by setting the XUDF(Transmit underflow) flag after wait for the
condition is over.

Cc: Alexander Shishkin <virtuoso@slind.org>
Acked-by: NMoiz Sonasath <m-sonasath@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

i2c_probe set the dev->errata flag, but omap_i2c_init cleared the flag again.
Prevent the overwrite of the errata flags.Move the errata handling to a unified
place in probe to prevent such errors.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTasslehoff Kjappfot <tasskjapp@gmail.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

If PM runtime get_sync fails return with the error
so that no further reads/writes goes through the interface.
This will avoid possible abort. Add a error message in case
of failure with the cause of the failure.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

    In omap_i2c_remove we are accessing the I2C_CON register without
    enabling the clocks. Fix the same by ensure device is accessible by calling
    pm_runtime_get_sync before accessing the registers and calling pm_runtime_put
    after accessing.

    This fixes the following crash.
    [  154.723022] ------------[ cut here ]------------
    [  154.725677] WARNING: at arch/arm/mach-omap2/omap_l3_noc.c:112 l3_interrupt_handler+0x1b4/0x1c4()
    [  154.725677] L3 custom error: MASTER:MPU TARGET:L4 PER2
    [  154.742614] Modules linked in: i2c_omap(-)
    [  154.746948] Backtrace:
    [  154.746948] [<c0013078>] (dump_backtrace+0x0/0x110) from [<c026c158>] (dump_stack+0x18/0x1c)
    [  154.752716]  r6:00000070 r5:c002c43c r4:df9b9e98 r3:df9b8000
    [  154.764465] [<c026c140>] (dump_stack+0x0/0x1c) from [<c0041a2c>] (warn_slowpath_common+0x5c/0x6c)
    [  154.768341] [<c00419d0>] (warn_slowpath_common+0x0/0x6c) from [<c0041ae0>] (warn_slowpath_fmt+0x38/0x40)
    [  154.776153]  r8:00000180 r7:c0361594 r6:c0379b48 r5:00080003 r4:e0838b00
    [  154.790771] r3:00000009
    [  154.791778] [<c0041aa8>] (warn_slowpath_fmt+0x0/0x40) from [<c002c43c>] (l3_interrupt_handler+0x1b4/0x1c4)
    [  154.803710]  r3:c0361598 r2:c02ef74c
    [  154.807403] [<c002c288>] (l3_interrupt_handler+0x0/0x1c4) from [<c0085f44>] (handle_irq_event_percpu+0x58/0
    [  154.818237]  r8:0000002a r7:00000000 r6:00000000 r5:df808054 r4:df8893c0
    [  154.825378] [<c0085eec>] (handle_irq_event_percpu+0x0/0x188) from [<c00860b8>] (handle_irq_event+0x44/0x64)
    [  154.835662] [<c0086074>] (handle_irq_event+0x0/0x64) from [<c0088ec0>] (handle_fasteoi_irq+0xa4/0x10c)
    [  154.845458]  r6:0000002a r5:df808054 r4:df808000 r3:c034a150
    [  154.846466] [<c0088e1c>] (handle_fasteoi_irq+0x0/0x10c) from [<c0085ed0>] (generic_handle_irq+0x30/0x38)
    [  154.854278]  r5:c034aa48 r4:0000002a
    [  154.862091] [<c0085ea0>] (generic_handle_irq+0x0/0x38) from [<c000fd38>] (handle_IRQ+0x60/0xc0)
    [  154.874450]  r4:c034ea70 r3:000001f8
    [  154.878234] [<c000fcd8>] (handle_IRQ+0x0/0xc0) from [<c0008478>] (gic_handle_irq+0x20/0x5c)
    [  154.887023]  r7:ffffff40 r6:df9b9fb0 r5:c034e2b4 r4:0000001a
    [  154.887054] [<c0008458>] (gic_handle_irq+0x0/0x5c) from [<c000ea80>] (__irq_usr+0x40/0x60)
    [  154.901153] Exception stack(0xdf9b9fb0 to 0xdf9b9ff8)
    [  154.907104] 9fa0:                                     beaf1f04 4006be00 0000000f 0000000c
    [  154.915710] 9fc0: 4006c000 00000000 00008034 ffffff40 00000007 00000000 00000000 0007b8d7
    [  154.916778] 9fe0: 00000000 beaf1b68 0000d23c 4005baf0 80000010 ffffffff
    [  154.931335]  r6:ffffffff r5:80000010 r4:4005baf0 r3:beaf1f04
    [  154.937316] ---[ end trace 1b75b31a2719ed21 ]--

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Linux PM list <linux-pm@vger.kernel.org>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

By definition, wait_for_completion_timeout() returns an unsigned value and
therefore, it is not necessary to check if the return value is less than zero
as this is not possible.

This is based on a patch from Jon Hunter <jon-hunter@ti.com>
Changes from his patch
- Declare a long as the wait_for_completion_timeout returns long.

Original patch is
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=ea02cece7b0000bc736e60c4188a11aaa74bc6e6Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Currently in probe
pm_runtime_put(dev->dev);

...
        /* i2c device drivers may be active on return from add_adapter() */
        adap->nr = pdev->id;
        r = i2c_add_numbered_adapter(adap);
        if (r) {
                dev_err(dev->dev, "failure adding adapter\n");
                goto err_free_irq;
        }
...

return 0;

err_free_irq:
        free_irq(dev->irq, dev);
err_unuse_clocks:
        omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
        pm_runtime_put(dev->dev);

This may access the i2c registers without the clocks in the error cases.
Fix the same by moving the pm_runtime_put after the error check.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

On OMAP4 we were writing 1 to IRQENABLE_CLR which cleared only
the arbitration lost interrupt. The patch intends to fix the same by writing 0
to the IE register clearing all interrupts.

This is based on the work done by Vikram Pandita <vikram.pandita@ti.com>.

The  changes from the original patch ...
-  Does not use the IRQENABLE_CLR register to clear as it is not mentioned
  to be legacy register IRQENABLE_CLR helps in  atomically
  setting/clearing specific interrupts, instead use the OMAP_I2C_IE_REG as we
  are clearing all interrupts.

Cc: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Currently the i2c driver calls the pm_runtime_enable and never
the disable. This may cause a warning when pm_runtime_enable
checks for the count match.Fix the same by calling
pm_runtime_disable in the error and the remove path.

Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The functions omap_i2c_unidle/idle are called from omap_i2c_runtime_resume
and omap_i2c_runtime_suspend which is compiled for CONFIG_PM_RUNTIME.
This patch removes the omap_i2c_unidle/idle functions and folds them
into the runtime callbacks.

This fixes the below warn when CONFIG_PM_RUNTIME is not defined

 CC      arch/arm/mach-omap2/board-ti8168evm.o
drivers/i2c/busses/i2c-omap.c:272: warning: 'omap_i2c_unidle' defined but not used
drivers/i2c/busses/i2c-omap.c:293: warning: 'omap_i2c_idle' defined but not used
  CC      net/ipv4/ip_forward.o
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

CONFIG_OF is not defined for OMAP1 yet and thus the omap1_defconfig build
generate an error for 3.3-rc1.

drivers/i2c/busses/i2c-omap.c: In function 'omap_i2c_probe':
drivers/i2c/busses/i2c-omap.c:1021:26: error: 'omap_i2c_of_match' undeclared (first use in this function)
drivers/i2c/busses/i2c-omap.c:1021:26: note: each undeclared identifier is reported only once for each function it appears in

Wrap omap_i2c_of_match with of_match_ptr() to prevent compilation error in case of OMAP1 build.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add initial DT support to retrieve the frequency using a
DT attribute instead of the pdata pointer if of_node exist.

Add documentation for omap i2c controller binding.

Based on original patches from Manju and Grant.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKevin Hilman <khilman@ti.com>

On OMAP4 OMAP_I2C_STAT_NACK is causing a timeout on the next access.
The isr cleans all flags in OMAP_I2C_CON_REG by setting OMAP_I2C_CON_STP
OMAP_I2C_CON_STP is also set in omap_i2c_xfer_msg on the last message.

According to the TI TSR the sequence for OMAP_I2C_STAT_NACK and
OMAP_I2C_STAT_AL are nearly the same.
Removing the OMAP_I2C_CON_STP part in the isr fix the problem.
Tested on OMAP4430 and OMAP3530 (here NACK was not a problem)
Fixes also booting on 2430sdp.
Signed-off-by: NJan Weitzel <j.weitzel@phytec.de>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Correct OMAP_I2C_SYSC_REG offset in omap4 register map.
Offset 0x20 is reserved and OMAP_I2C_SYSC_REG has 0x10 as offset.
Signed-off-by: NAlexander Aring <a.aring@phytec.de>
[khilman@ti.com: minor changelog edits]
Cc: stable@vger.kernel.org
Signed-off-by: NKevin Hilman <khilman@ti.com>

Currently the fifo depth is set to zero for OMAP4 which disables
the FIFO usage. This patch enables the FIFO usage for I2C transactions
on OMAP4 also.

Tested on omap4430 and 3430.
Tested-and-Reported-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Current usage of runtime PM is not quite correct.  The actual
idle/unidle of the I2C hardware should not happen until the runtime PM
callbacks are called.  Therefore, change omap_i2c_[un]idle() functions
to only be called from the runtime PM callbacks (when usage count
transitions to/from zero.)

Also, the runtime PM core does usage counting and replaces
functionality currently managed by the dev->idle flag.  Remove usage
of dev->idle in favor of using runtime PM, and checking status using
pm_runtime_suspended().
Signed-off-by: NKevin Hilman <khilman@ti.com>

A pointer to the struct device associated with the i2c device is
already kept in the struct omap_i2c_dev, so use omap_i2c_device to
find the pointer to struct device.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Currently for OMAP4 the I2C_WE is not programmed.
This patch enables the programming for OMAP4.

This patch fixes a bad conflict resolution.
This effectively restores the following commit

Commit 120bdaa4[i2c-omap: Program I2C_WE on OMAP4 to enable i2c wakeup]

which got changed by

Commit a3a7acbc[I2C: OMAP2+: address confused probed version naming]
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Reported-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The IP version is prepended to the existing printed probed
version as an "epoch" version.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch eliminates all cpu_...() tests from the OMAP I2C driver.

Instead, it uses the functionality flags in the platform data to make
the decisions about product variations the driver needs to handle.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The driver reflects the confusion that probed I2C revision
from the hardware of 0x40 means it is on an OMAP4430.

However, you will probe the same 0x40 ID on an OMAP3530.  So
this patch changes the name to reflect that.

It also clarifies that the original name OMAP_I2C_REV_2 is
referring to some ancient OMAP1 revision number, not to be
confused with the IP revisions this patch series introduces.

Similarly the term "rev" is used in the ancient OMAP1 ISR,
the term is changed to use omap1 instead.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This solves the main problem the patch series is about.  Prior
to this patch on OMAP3530 the driver wrongly interprets the I2C
peripheral unit's own reported revision as meaning it is running
on an IP V2 device and must use the extended registers.

In fact OMAP3530 is IP V1 with the smaller register set, the
reason for the confusion is that the hardware does in fact report
having the same IP revision index as is found on an OMAP4430,
which really is IP V2 and has the extended registers.

This corrects the test for which registers to use so that it
decides using hwmod knowledge found in the platform_data.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Change the register map names to reflect the IP revision they
are representing, and use the platform_data IP revision index
to select between them at init time.

Eliminates 1 of 17 cpu_...() calls in the driver.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The OMAP I2C driver dynamically chooses between two register sets of
differing sizes depending on the cpu type it finds itself on.

It has been observed that the existing code references non-existing
registers on OMAP3530, because while it correctly chose the smaller
register layout based on cpu type, the code uses the probed register
ID to decide if to execute code referencing an extra register, and
both register layout devices on OMAP3530 and OMAP4430 report the same
probed ID of 0x40.

This patch changes the extended register names only found on IP V2
of the I2C peripheral unit accordingly to help show up errors in usage.

Cc: patches@linaro.org
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This reverts commit adf6e079.

Remove system PM methods which can race with runtime PM methods.

Also, as of v3.1, the PM domain level code for OMAP handles device
power state transistions automatically for devices, so drivers no
longer need to specifically call the bus/pm_domain methods themselves.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Make sure that the 'static' keywork is at the beginning of declaration
for drivers/i2c/busses/i2c-omap.c

This gets rid of warnings like
  warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

For the I2C module to be wakeup capable, programming I2C_WE register (which
was skipped for OMAP4430) is needed even on OMAP4.

This fixes i2c controller timeouts which were seen recently with the static
dependency being cleared between MPU and L4PER clockdomains.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[ben-linux@fluff.org: re-flowed description]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fixup the whitespace error noticed in cb527edeSigned-off-by: NBen Dooks <ben-linux@fluff.org>

This errata occurs when the ARDY interrupt generation is enabled.
At the begining of every new transaction the ARDY interrupt is cleared.

On continuous i2c transactions where after clearing the ARDY bit from
I2C_STAT register (clearing the interrupt), the IRQ line is reasserted and the
I2C_STAT[ARDY] bit set again on 1. In fact, the ARDY status bit is not cleared
at the write access to I2C_STAT[ARDY] and only the IRQ line is deasserted and
then reasserted. This is not captured in the usual errata documents.

The workaround is to have a double clear of ARDY status in irq handler.
Signed-off-by: NRichard woodruff <r-woodruff2@ti.com>
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

fix the build break when !CONFIG_SUSPEND

drivers/i2c/busses/i2c-omap.c:1173: error: lvalue required as unary '&' operand
make[3]: *** [drivers/i2c/busses/i2c-omap.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

When runtime PM is enabled, each OMAP i2c device is suspended after
each i2c xfer.  However, there are two cases when the static suspend
methods must be used to ensure the devices are suspended:

1) runtime PM is disabled, either at compile time or dynamically
    via /sys/devices/.../power/control.
2) an i2c client driver uses i2c during it's suspend callback, thus
   leaving the i2c driver active (NOTE: runtime suspend transitions are
   disabled during system suspend, so i2c activity during system
   suspend will runtime resume the device, but not runtime (re)suspend it.)

Since the actual work to suspend the device is handled by the
subsytem, call the bus methods to take care of it.

NOTE: This takes care of a known suspend problem on OMAP3 where the
TWL RTC driver does i2c xfers during its suspend path leaving the i2c
driver in an active state (since runtime suspend transistions are
disabled.)
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Ordinary I2C read consist of two messages. First a write operation
to tell register address and then read operation to get data.
CPU wake up latency is set and removed twice in read case.
Set latency requirement before the message processing loop
and remove the requirement after the loop to remove latency
adjustment operations between the messages.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The convention for omap device naming is omap_XXX.

Rename the device and driver name in order to stick
to this naming convention.

Change device name in clock nodes as well.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch converts the i2c driver to use PM runtime apis
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

If the i2c bus receives an interrupt with both BB (bus busy) and
ARDY (register access ready) statuses set during the tranfer of the last message
the bus was put to idle while still busy.

This caused bus to timeout.
Signed-off-by: NMathias Nyman <mathias.nyman@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Clean up existing Errata 1p153 handling to use generic
errata handling mechanism through dev flag.
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.

Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.

Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.

Updates by Kevin as requested by Tony:

- Remove omap_set_i2c_constraint_func() in favor of conditionally
  adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
  conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
  OMAP PM function can be used directly in pdata.

Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>