Recognise the new Packet Memory and RX Data Path counters.

The following counters are added:
rx_pm_{trunc,discard}_bb_overflow - burst buffer overflowed.  This should not
 occur if BB correctly configured.
rx_pm_{trunc,discard}_vfifo_full - not enough space in packet memory.  May
 indicate RX performance problems.
rx_pm_{trunc,discard}_qbb - dropped by 802.1Qbb early discard mechanism.
 Since Qbb is not supported at present, this should not occur.
rx_pm_discard_mapping - 802.1p priority configured to be dropped.  This should
 not occur in normal operation.
rx_dp_q_disabled_packets - packet was to be delivered to a queue but queue is
 disabled.  May indicate misconfiguration by the driver.
rx_dp_di_dropped_packets - parser-dispatcher indicated that a packet should be
 dropped.
rx_dp_streaming_packets - packet was sent to the RXDP streaming bus, ie. a
 filter directed the packet to the MCPU.
rx_dp_emerg_{fetch,wait} - RX datapath had to wait for descriptors to be
 loaded.  Indicates performance problems but not drops.

These are only provided if the MC firmware has the
PM_AND_RXDP_COUNTERS capability.  Otherwise, mask them out.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Previously, efx_ef10_stat_mask returned a static const unsigned long[], which
meant that each possible mask had to be declared statically with
STAT_MASK_BITMAP.  Since adding a condition would double the size of the
decision tree, we now create the bitmask dynamically.

To do this, we have two functions efx_ef10_raw_stat_mask, which returns a u64,
and efx_ef10_get_stat_mask, which fills in an unsigned long * argument.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The indices in nic_data->stats need to match the EF10_STAT_whatever
enum values.  In efx_nic_update_stats, only mask; gaps are removed in
efx_ef10_update_stats.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

DT-based mv643xx_eth probes and creates platform_devices for the
port devices on its own. To allow fixups for ports based on the
device_node, we need to set .of_node of the corresponding device
with the correct node.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The periodic statistics timer gets started at port _probe() time, but
is stopped on _stop() only. In a modular environment, this can cause
the timer to access already deallocated memory, if the module is unloaded
without starting the eth device. To fix this, we add the timer right
before the port is started, instead of at _probe() time.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each port driver installs a periodic timer to update port statistics
by calling mib_counters_update. As mib_counters_update is also called
from non-timer context, we should not reschedule the timer there but
rather move it to timer-only context.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eee_get_cur assumes that the output data is already zeroed. It can
read-modify-write the advertised field:

              if (ipcnfg & E1000_IPCNFG_EEE_100M_AN)
2594			edata->advertised |= ADVERTISED_100baseT_Full;

This is ok for the normal ethtool eee_get call, which always
zeroes the input data before.

But eee_set_cur also calls eee_get_cur and it did not zero the input
field. Later on it then compares agsinst the field, which can contain partial
stack garbage.

Zero the input field in eee_set_cur() too.

Cc: jeffrey.t.kirsher@intel.com
Cc: netdev@vger.kernel.org
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Highbank and Midway xgmac h/w have different number of MAC address filter
registers with 7 and 31, respectively. Highbank has been wrong, so fix it
and detect the number of filter registers at run-time. Unfortunately,
the version register is the same on both SOCs, so simply test if write to
the last filter register will take a value. It always reads as 0 if not.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even in promiscuous mode, we need to add filter addresses for correct
operation. This fixes silent failures when using a bridge and adding
addresses using the "bridge fdb add" command.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 2ee68f62 (net: calxedaxgmac: fix various errors in
xgmac_set_rx_mode), a fix to clean-up old address entries was added.
However, the loop to zero out the entries failed to increment the register
address resulting in only 1 entry getting cleared. Fix this to correctly
use the loop index. Also, the end of the loop condition was off by 1 and
should have been <= rather than <.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Interface needs to be brought down and up while configuring SR-IOV.
  Protect interface up/down using rtnl_lock()/rtnl_unlock()
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dma descriptors indexes are only initialized on the probe function.

If a packet is on the buffer when temac_stop is called, the dma
descriptors indexes can be left on a incorrect state where no other
package can be sent.

So an interface could be left in an usable state after ifdow/ifup.

This patch makes sure that the descriptors indexes are in a proper
status when the device is open.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.

In this particular case __initdata is incorrect as moxart_mac_driver
can be used after the driver gets initialized.

Also while at it static-ize moxart_mac_driver.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.

For instance:

	fsl,cksel = <0>;

for using external (TSEC_TMR_CLK input) high precision timer
reference clock.

Other acceptable values:

	<1> : eTSEC system clock
	<2> : eTSEC1 transmit clock
	<3> : RTC clock input

When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: NAida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 894116bd.

I applied the wrong version of this patch, correct
version coming up.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.

For instance:

	fsl,cksel = <0>;

for using external (TSEC_TMR_CLK input) high precision timer
reference clock.

Other acceptable values:

	<1> : eTSEC system clock
	<2> : eTSEC1 transmit clock
	<3> : RTC clock input

When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: NAida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Commit 7e2cf4fe
  ("qlcnic: change driver hardware interface mechanism")
  has overwritten
  commit b43e5ee7
  ("qlcnic: Register device in FAILED state")
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN priority is not being displayed for a VF currently when user executes
"ip link show" command. This patch fixes it.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thix fix allows the VLAN priority to be configured for a VF interface
via the "ip link set DEVICE vf NUM" path.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now the VF interfaces have privilege to add VLANs.
Allow VLANs to be configured on these interfaces.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In BE3-R, when UMC is enabled, the number of VLANs that can be added
to the interface is reduced to 15.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the interface runs out of the allocated entries in VLAN table,
we program the interface in VLAN promiscuous mode.
Use OPCODE_COMMON_NTWK_RX_FILTER to set VLAN Promiscuous mode
instead of OPCODE_COMMON_NTWK_VLAN_CONFIG.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Size of be_nic_res_desc structure is incorrect. Fix it.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tx on SH-R can lockup if the packet size is less than 32 bytes.
Pad such packets to a safer 36-byte size.
Patch uses the Lancer-R workaround - which checks for packet <= 32-bytes
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

coccicheck shows:

drivers/net/ethernet/intel/i40e/i40e_adminq.c:704:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:763:1-7: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:810:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_common.c:510:2-8: Replace memcpy
with struct assignment

Fix each of them with a *a = *b;
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As mentioned by Joe Perches, clean up return values in some functions
making sure to have consistent return types, not mixing types.

A couple of Joe's comments suggested returning void, but since
the functions in question are ndo defined, the return values are fixed.
So make a comment in the header that notes this is a function called by
net_device_ops.

v2: fix post increment bug in return

CC: Joe Perches <joe@perches.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When calling admin queue functions the driver should use aq_ret
variable to help make clear that the return value is not a regular
return variable.

This allows for clean up of the return types that were previously
converted to int.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As mentioned by Joe Perches clean up a loop flow.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As mentioned by Joe Perches, we should be using
foo = alloc(...)
if (!foo)
	return -ENOMEM;

return 0;
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add back 82580 loopback tests to ethtool.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).

Peter Boström noticed and reported the bug.
Signed-off-by: NRoger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also changed a log message to indicate that memory was not allocated
instead of memory not available!
Signed-off-by: NMalahal Naineni <malahal@us.ibm.com>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In my patch c194992c ("skge: fix
broken driver") I didn't fix the skge bug correctly. The value of the
new mapping (not old) was passed to pci_unmap_single.

If we enable CONFIG_DMA_API_DEBUG, it results in this warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:986 check_sync+0x4c4/0x580()
skge 0000:02:07.0: DMA-API: device driver tries to sync DMA memory it has
not allocated [device address=0x000000023a0096c0] [size=1536 bytes]

This patch makes the skge driver pass the correct value to
pci_unmap_single and fixes the warning. It copies the old descriptor to
on-stack variable "ee" and unmaps it if mapping of the new descriptor
succeeded.

This patch should be backported to 3.11-stable.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Reported-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).

Wait until firmware ack is written before unlocking channel
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.

This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>