- 10 8月, 2013 2 次提交
-
-
由 Amitkumar Karwar 提交于
Coalesce filters are configured in firmware based on settings received from cfg80211. Packet type which is required by firmware is determined based on provided patterns in a rule: Unicast: if pattern '01' with offset 0 is found Multicast: if pattern '33:33' or '01:00:5e' with offset 0 is found Broadcast: if pattern 'ff:ff:ff:ff' with offset 0 is found Some example coalesce configuration files: 1) Coalesce Rx data packets from 192.168.0.88 mac address of our device is 00:50:43:21:53:7A Source IP address offset comes out as 52 after following calculations: 32 bytes of HW 802.11 header + 8 bytes LLC + 12 bytes in IPV4 header till source IP address Destination mac is at offset 6 in HW header. delay=100 condition=1 patterns=01,6+00:50:43:22,10+53:7A,52+c0:a8:00:58 2) Coalesce all broadcast and multicast packets(Multiple packet types are not allowed in a single rule. Hence created separate rules) delay=400 condition=1 patterns=33:33 delay=400 condition=1 patterns=ff:ff:ff:ff Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
Their names were generic. We need to define similar macros for coalesce feature. Hence they are renamed here. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 24 7月, 2013 1 次提交
-
-
由 Amitkumar Karwar 提交于
We already have 'struct mwifiex_ie_types_header' with same definition. Hence host_cmd_tlv is removed in this patch. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 5月, 2013 1 次提交
-
-
由 Amitkumar Karwar 提交于
User can provide a text file containing calibration data in hex format while loading mwifiex module. It will be downloaded to firmware. eg. insmod mwifiex.ko cal_data_cfg=cal_data.conf Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 26 3月, 2013 1 次提交
-
-
由 Yogesh Ashok Powar 提交于
Currently, default VHT configuration from the firmware is used for the VHT operations. Adding vhtcfg command to configure the firmware based on input received from cfg. Enable VHT for AP mode only when cfg80211_ap_settings has a VHT IE i.e., when ieee80211ac is set to 1 in the hostapd.conf. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 3月, 2013 2 次提交
-
-
由 Amitkumar Karwar 提交于
Currently 'magic-packet' and 'patterns' options in 'iw wowlan' command are supported. Appropriate packet filters for wowlan are configured in firmware based on provided patterns and/or magic-packet option. For examples, wake-on ARP request for 192.168.0.100: iw phy0 wowlan enable patterns ff:ff:ff:ff:ff:ff 20+08:06 46+c0:a8:00:64 wake-on RX packets sent from IP address 192.168.0.88: iw phy0 wowlan enable patterns 34+c0:a8:00:58 wake-on RX packets with TCP destination port 80 iw phy0 wowlan enable patterns 44+50 wake-on MagicPacket: iw phy0 wowlan enable magic-packet wake-on MagicPacket or patterns: iw phy0 wowlan enable magic-packet patterns 12+00:11:22:33:44:55 18+00:50:43:21 wake-on IPv4 multicast packets: iw phy0 wowlan enable patterns 01:00:5e wake-on IPv6 multicast packets: iw phy0 wowlan enable patterns 33:33 disable all wowlan options iw phy0 wowlan disable Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
As we are adding a few more macros in this category in next patch, this cleanup work is required. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 19 2月, 2013 1 次提交
-
-
由 Yogesh Ashok Powar 提交于
For STA mode, collect VHT realated IEs from the Beacons or Probe Responses and append similar VHT related IEs to association requests. For AP mode, get VHT related capability information and share it with cfg80211 at the time of wiphy register. This information is further used by cfg80211 and hostapd to start an AP with 802.11AC support. Currently only 8897 supports 802.11AC. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NNishant Sarmukadam <nishants@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NFrank Huang <frankh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 08 1月, 2013 1 次提交
-
-
由 Avinash Patil 提交于
This patch uses pci_alloc_consistent and pci_free_consistent APIs for mwifiex_pcie driver. Consistent DMA memory is allocated for TX, RX and event rings. Command buffer and command response buffer also uses map/unmap memory APIs to download commands and get command responses. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 29 9月, 2012 5 次提交
-
-
由 Stone Piao 提交于
When cfg80211 calls to change interface type for P2P GO, send P2P mode config commands to firmware and set bss role and bss mode accordingly. Signed-off-by: NStone Piao <piaoyun@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stone Piao 提交于
When cfg80211 calls to change interface type for P2P client, send P2P mode config commands to firmware. Signed-off-by: NStone Piao <piaoyun@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stone Piao 提交于
The driver will send some commands to firmware during the initialization. Currently these commands are sent asynchronously, which means that we firstly insert all of them to a pre-allocated command queue, and then start to process them one by one. The command queue will soon be exhausted if we keep adding new initialization commands. This issue can be resolved by sending initialization commands synchronously because each command is consumed and the buffer is recycled before queuing next command. Signed-off-by: NStone Piao <piaoyun@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stone Piao 提交于
Add a new command to implement remain_on_channel and cancel_remain_on_channel. Signed-off-by: NStone Piao <piaoyun@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stone Piao 提交于
Add a new command to implement mgmt_frame_register. Signed-off-by: NStone Piao <piaoyun@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 08 9月, 2012 1 次提交
-
-
由 Wei Yongjun 提交于
Using is_broadcast_ether_addr() instead of directly use memcmp() to determine if the ethernet address is broadcast address. Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 8月, 2012 1 次提交
-
-
由 Bing Zhao 提交于
The key length can be 32 bytes for TKIP and 16 bytes for AES_CMAC. 'smatch' warns on memcpy using key_len variable to copy data to a 16 bytes buffer. Use fixed length to avoid the warning. Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 8月, 2012 2 次提交
-
-
由 Ying Luo 提交于
The sequence counter will be sent to firmware via key_material command. Signed-off-by: NYing Luo <luoy@marvell.com> Signed-off-by: NStone Piao <piaoyun@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ying Luo 提交于
This array was used for wapi_rxpn only. Now it will be used for AES_CMAC as well. So make a generic name for it. Signed-off-by: NYing Luo <luoy@marvell.com> Signed-off-by: NStone Piao <piaoyun@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 18 7月, 2012 1 次提交
-
-
由 Amitkumar Karwar 提交于
1) Recently we removed set_channel cfg80211 handler. Also, cfg80211 blocks ibss connection requests if ibss network is already started /joined. Hence the code to restart ibss network in new channel (mwifiex_drv_change_adhoc_chan() function) becomes redundant. 2) mwifiex_bss_set_channel() function is redundant. It does some error checking and calculate adhoc start band and adhoc channel. Cfg80211 already takes care of error checking and provides correct channel information to the driver. Adhoc start band is already calculated in mwifiex_set_rf_channel() function. Other associated code is also removed in this patch. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 10 7月, 2012 1 次提交
-
-
由 Amitkumar Karwar 提交于
This enables user to set mode of Tx/Rx path using "iw set antenna" command. For non MIMO chips, the command will be used for selecting specific antenna or configuring antenna diversity mode. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 29 6月, 2012 1 次提交
-
-
由 Amitkumar Karwar 提交于
"priv->max_tx_power_level" and "priv->min_tx_power_level" variables are initialized to maximum and minimum power levels supported by hardware by sending correct firmware command. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 6月, 2012 1 次提交
-
-
由 Joe Perches 提交于
Adding casts of objects to the same type is unnecessary and confusing for a human reader. For example, this cast: int y; int *p = (int *)&y; I used the coccinelle script below to find and remove these unnecessary casts. I manually removed the conversions this script produces of casts with __force, __iomem and __user. @@ type T; T *p; @@ - (T *)p + p Neatened the mwifiex_deauthenticate_infra function which was doing odd things with array pointers and not using is_zero_ether_addr. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 5月, 2012 2 次提交
-
-
由 Avinash Patil 提交于
Modify key related cfg80211 handlers to copy peer mac address for pairwise keys. If peer mac address is not present or group keys, it will be sent as broadcast mac address. This would be required since hostapd downloads per peer PTK. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
Commands like IBSS coalescing status, power save, 11D should be handled only when bss_type is STA. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 24 4月, 2012 1 次提交
-
-
由 Amitkumar Karwar 提交于
This patch supports Avastar 88W8797 chipset with USB interface. The corresponding firmware image file is located at: "mrvl/usb8797_uapsta.bin" Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NFrank Huang <frankh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 13 4月, 2012 1 次提交
-
-
由 Bing Zhao 提交于
This is a copy-n-paste error introduced in recent patch "mwifiex: add set_cqm_rssi_config handler support". Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 10 4月, 2012 1 次提交
-
-
由 Amitkumar Karwar 提交于
In this handler LOW_RSSI and HIGH_RSSI events are subscribed to FW using provided threshold value so that FW will monitor connection quality and trigger any of these events. Driver will notify cfg80211 about connection quality based on inputs from FW and provided hysteresis. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 15 3月, 2012 1 次提交
-
-
由 Yogesh Ashok Powar 提交于
For sta_cmd.c and sta_cmdresp.c Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 2月, 2012 1 次提交
-
-
由 Amitkumar Karwar 提交于
1) Remove unnecessary switch case usage. 2) Replace "X=cpu_to_le16(le16_to_cpu(X) + Y)" by "le16_add_cpu(X, Y)" 3) Declare "ul_temp" variable as u16 instead of u32 to avoid unnecessary typecasting Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 22 12月, 2011 1 次提交
-
-
由 Amitkumar Karwar 提交于
Replace driver specific macros with the corresponding IEEE80211_HT_PARAM_CHA_SEC_* macros defined in ieee80211.h. Also, rename 'adapter->chan_offset' to 'adapter->sec_chan_offset' for consistency. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 13 10月, 2011 1 次提交
-
-
由 Amitkumar Karwar 提交于
This patch supports 88W8766P chipset with a PCIe interface. The corresponding firmware image file is located at: "mrvl/pcie8766_uapsta.bin" Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NRamesh Radhakrishnan <rramesh@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NFrank Huang <frankh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 12 7月, 2011 1 次提交
-
-
由 Amitkumar Karwar 提交于
Currently device is not able to transmit in 40MHz in spite of enabling 40MHz support in HTCapInfo IE in assoc req, because 11n specific FW capabilities for transmission are not initialized. This patch adds code to initilize these capabilities. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 6月, 2011 1 次提交
-
-
由 Dan Carpenter 提交于
Prior to a5ffddb7 "mwifiex: remove casts of void pointers" the code assumed that the data_buf parameter could be a NULL pointer. The patch preserved some NULL checks but not consistently, so there was a potential for NULL dereferences and it changed the behavior. This patch restores the original behavior. Signed-off-by: NDan Carpenter <error27@gmail.com> Acked-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 6月, 2011 1 次提交
-
-
由 Amitkumar Karwar 提交于
In some cases local pointers are used to cast void pointers passed to the function. Those unnecessary local pointers are also removed. This patch was inspired by Joe Perches' patch [PATCH net-next 1/2] wireless: Remove casts of void *; and the comments from Julian Calaby. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Cc: Joe Perches <joe@perches.com> Cc: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 06 5月, 2011 1 次提交
-
-
由 Yogesh Ashok Powar 提交于
Skip initialization of local variables with some default values if the values are not going to be used further down the code path. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 15 4月, 2011 2 次提交
-
-
由 Amitkumar Karwar 提交于
Some function parameters become useless after previous cleanup changes. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
1) remove mwifiex_alloc_fill_wait_queue() and mwifiex_request_ioctl() 2) avoid dynamic allocation of wait queue 3) remove unnecessary mwifiex_error_code macros that were used mainly by the wait queue status code 4) remove some abstraction functions 5) split mwifiex_prepare_cmd() to mwifiex_send_cmd_async() and mwifiex_send_sync() to handle asynchronous and synchronous commands respectively Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 13 4月, 2011 1 次提交
-
-
由 Yogesh Ashok Powar 提交于
Instead of having separate key information definitions for each type of key, a common key information bitmap is used. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 05 4月, 2011 1 次提交
-
-
由 Bing Zhao 提交于
replace them with NL80211_IFTYPE_ macros Also remove redundant functions mwifiex_drv_get_mode() and mwifiex_bss_ioctl_mode(). Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 31 3月, 2011 1 次提交
-
-
由 Bing Zhao 提交于
This driver adds WiFi support for Marvell 802.11n based chipsets with SDIO interface. Currently only SD8787 is supported. More chipsets will be supported later. drivers/net/wireless/mwifiex/ Signed-off-by: NNishant Sarmukadam <nishants@marvell.com> Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NMarc Yang <yangyang@marvell.com> Signed-off-by: NRamesh Radhakrishnan <rramesh@marvell.com> Signed-off-by: NFrank Huang <frankh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-