The hardware erratum workaround where the TXDCTL register must be the same
setting for both queues should always be done.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a patch from Prabhakar Kushwaha <prabhakar@freescale.com>, set
appropriate default interrupt mode dependent on whether CONFIG_PCI_MSI
is enabled in the kernel configuration and if the hardware supports
MSI-X.  Set the module parameter log message accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make it more like how igb does it, with some additional error checking.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations.  Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable RPS by default.  Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.

v2: added ethtool command to query flow hashing behavior per Ben Hutchings
    and changed the type of rsskey to cleanup the setting of the register
    array and avoid unnecessary casts (as pointed out by Joe Perches).
    The long error messages are not changed since there is nothing in
    the kernel ./Documentation that suggests the preferred method for
    dealing with long messages other than to never break strings; leaving
    them as-is for now.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
   e1000_rx_checksum() instead of in each call to the function

v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This driver adds support for Xilinx 10/100/1000 AXI Ethernet.

It can be used, for instance, on Xilinx boards with a Microblaze
architecture like the ML605.

The patch is against the latest net-next tree and checkpatch clean.
Signed-off-by: NAriane Keller <ariane.keller@tik.ee.ethz.ch>
Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We introduced a new return here but forgot to drop the lock.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using module_platform_driver can make the code smaller.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

STM has a device ID within its own VENDOR space, and it is being
used in the STA2X11 I/O Hub.
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit "db8857bf stmmac: use an unique MDIO bus name" my
device stopped being probed because two different names were being
used in different places. This fixes the inconsistency.
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Florian Fainelli <florian@openwrt.org>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3_start_xmit() makes the wrong assumption for TSOV6 that skb->head
doesnt include any payload data.

if (skb_is_gso_v6(skb))
	hdr_len = skb_headlen(skb) - ETH_HLEN;

This is not true anymore after commit f07d960d (tcp: avoid frag
allocation for small frames)

We should instead use : skb_transport_offset(skb) + tcp_hdrlen(skb)

Its also true for IPv4
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This also changes the cleanup logic slightly to aggregate
completed notifications for multiple packets.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These statistics helped me a lot while searching who is losing
packets in my setup.
I added these stats to MIB group since they are very similar,
but just in other registers.
I have tested this patch on 88F6281 SoC.
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macro `CHIP_IS_E1x' requires `bp' to be initialized.
As `bp' is not yet initialized during this phase of `bnx2x_init_dev',
it accessed uninitialized fields in the struct.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previosuly, in MF modes `ethtool -S' lacked some of the statistics
which appeared in non-MF modes. This has been fixed.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon insertion of elements into the execution queue, it is validated
that there are enough credits to support additional vlan-macs,
and the credits are consumed. However, when removing a pending
command in `bnx2x_vland_mac_del_all' the consumed credits are not
released, which might cause leakage and eventually the inability to
add new vlan-macs in certain scenarios.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently RSS rings are not created in a multi-channel config.
RSS rings can be created on one (out of four) interfaces per port in a
multi-channel config. Doing this insulates the driver from a FW bug wherin
multi-channel config is wrongly reported even when not enabled. This also
helps performance in a multi-channel config, as one interface per port gets
RSS rings.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver should check for mapping errors.
Machines with limited DMA maps may return an error when a PCI map is
requested (not an issue on standard x86).

Also use upper/lower 32 bits macros for clarity.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Skge device would assert carrier (link up) as soon as network device open
was called, rather than waiting until PHY has detected link.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slave async events were mapped to single eq. This patch fixes this issue, so
the slaves can map the async events to any eq.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Num mtts from profile is really the number of mtt segments.
Thus, in make profile, to get the proper number of MTT entries,
must multiply num_mtts by mtts per segment.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Virtual Functions should not be aware their function number.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In native mode display all available staticstics.
In SRIOV mode on VF display only SW counters statistics,
in SRIOV mode on hypervisor display SW counters and errors (got from FW)
statistics.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In multifunction mode - DUMP_STATS command is not executed
for VFs.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix: Not all stats fields were cleared.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petriln <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

reverting back change that access enic->num_vfs outside
CONFIG_PCI_IOV
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The arrays of function pointers should be const to make life harder
for rootkits.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes sparse warnings:
drivers/net/ethernet/intel/ixgbevf/vf.c:418:21: warning: symbol 'ixgbevf_82599_vf_info' was not declared. Should it be static?
drivers/net/ethernet/intel/ixgbevf/vf.c:423:21: warning: symbol 'ixgbevf_X540_vf_info' was not declared. Should it be static?
drivers/net/ethernet/intel/ixgbevf/mbx.c:331:29: warning: symbol 'ixgbevf_mbx_ops' was not declared. Should it be static?
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mailbox interrupt routine might cause a race condition sometimes
and cause a message to be missed.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is meant to address possible issues with the IXGBE register
defines generating incorrect values when given a complex expression for the
register offset.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This irq disable/enable pair used to wrap access to the driver's vlgrp
struct, which is no longer present. So, then, this could also so no longer
be present.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cast and comment are unnecessary in the current upstream kernel.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NGarrett, RobertX E <robertx.e.garrett@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>