Execution of break instruction, trap instructions, emulation of unaligned
loads or floating point instructions - anything that tries to read the
instruction's opcode from userspace - needs read access to a page.

RIXI (Read Inhibit / Execute Inhibit) support however allows the creation of
pags that are executable but not readable.  On such a mapping the attempted
load of the opcode by the kernel is going to cause an endless loop of
page faults.

The quick workaround for this is to disable the combinations that the kernel
currently isn't able to handle which are executable mappings.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Without this we end taking execeptions in an endless loop hanging the
thread.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On Malta, since commit a87ea88d ("MIPS: Malta: initialise the RTC at
boot"), the RTC is reinitialised and forced into binary coded decimal
(BCD) mode during init, even if the bootloader has already initialised
it, and may even have already put it into binary mode (as YAMON does).
This corrupts the current time, can result in the RTC seconds being an
invalid BCD (e.g. 0x1a..0x1f) for up to 6 seconds, as well as confusing
YAMON for a while after reset, enough for it to report timeouts when
attempting to load from TFTP (it actually uses the RTC in that code).

Therefore only initialise the RTC to the extent that is necessary so
that Linux avoids interfering with the bootloader setup, while also
allowing it to estimate the CPU frequency without hanging, without a
bootloader necessarily having done anything with the RTC (for example
when the kernel is loaded via EJTAG).

The divider control is configured for a 32KHZ reference clock if
necessary, and the SET bit of the RTC_CONTROL register is cleared if
necessary without changing any other bits (this bit will be set when
coming out of reset if the battery has been disconnected).

Fixes: a87ea88d ("MIPS: Malta: initialise the RTC at boot")
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Reviewed-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.14+
Patchwork: https://patchwork.linux-mips.org/patch/10739/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit eeb53895 ("MIPS: unaligned: Prevent EVA instructions on kernel
unaligned accesses") renamed the Load* and Store* defines in unaligned.c
to _Load* and _Store* as part of its fix. One define was missed out which
causes big endian R6 kernels to fail to build.

arch/mips/kernel/unaligned.c:880:35:
error: implicit declaration of function '_StoreDW'
 #define StoreDW(addr, value, res) _StoreDW(addr, value, res)
                                   ^
Signed-off-by: NJames Cowgill <James.Cowgill@imgtec.com>
Fixes: eeb53895 ("MIPS: unaligned: Prevent EVA instructions on kernel unaligned accesses")
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10575/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

p->thread.user_cpus_allowed is zero-initialized and is only filled on
the first sched_setaffinity call.

To avoid adding overhead in the task initialization codepath, simply OR
the returned mask in sched_getaffinity with p->cpus_allowed.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10740/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit 01306aea ("MIPS: prepare for user enabling of CONFIG_OF")
changed the guards in asm/prom.h from CONFIG_OF to CONFIG_USE_OF, but
missed the actual function declarations in kernel/prom.c, which have
additional dependencies.

Fixes the following build error:

  CC      arch/mips/kernel/prom.o
arch/mips/kernel/prom.c: In function '__dt_setup_arch':
arch/mips/kernel/prom.c:54:2: error: implicit declaration of function 'early_init_dt_scan' [-Werror=implicit-function-declaration]
  if (!early_init_dt_scan(bph))
  ^

Fixes: 01306aea ("MIPS: prepare for user enabling of CONFIG_OF")
Signed-off-by: NJonas Gorski <jogo@openwrt.org>
Acked-by: NRob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Patchwork: https://patchwork.linux-mips.org/patch/10741/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit 6134d949 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
added support for 64-bit FPU on a 32-bit MIPS R6 processor but it missed
the 64-bit CPU case leading to FPU failures when requesting FR=1 mode
(which is always the case for MIPS R6 userland) when running a 32-bit
kernel on a 64-bit CPU. We also fix the MIPS R2 case.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Fixes: 6134d949 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
Reviewed-by: NPaul Burton <paul.burton@imgtec.com>
Cc: <stable@vger.kernel.org> # 4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10734/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit 2ae416b1 ("mm: new mm hook framework") introduced an empty
header file (mm-arch-hooks.h) for every architecture, even those which
doesn't need to define mm hooks.

As suggested by Geert Uytterhoeven, this could be cleaned through the use
of a generic header file included via each per architecture
asm/include/Kbuild file.

The PowerPC architecture is not impacted here since this architecture has
to defined the arch_remap MM hook.
Signed-off-by: NLaurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pass 1 parts had a number of significant erratas and were only available
in small numbers and under NDA.  Full support also required the use of a
special toolchain that kept branches properly aligned.  These workarounds
were never upstreamed and the only toolchain known to have them is
Montavista's GCC 3.0-based toolchain which completly obsoleted if not
useless these days.

So now that automated testing has tripped over the user of the
-msb1-pass1-workarounds option, rather than fixing it remove support for
pass 1 parts.

Probably nobody will notice.  I seem to own the last know pass 1 board
and I haven't noticed another one in the wild in the past decade, at
least.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

MIPS32r6 code requires FP64 (ie. FR=1) support. Building a kernel with
support for MIPS32r6 binaries but without support for O32 with FP64 is
therefore a problem which can lead to incorrectly executed userland.

CONFIG_MIPS_O32_FP64_SUPPORT is already selected when the kernel is
configured for MIPS32r6, but not when the kernel is configured for
MIPS64r6 with O32 compat support. Select CONFIG_MIPS_O32_FP64_SUPPORT in
such configurations to prevent building kernels which execute MIPS32r6
userland incorrectly.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v4.0-
Cc: linux-mips@linux-mips.org
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10674/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

arch/mips/tools/offset.c was renamed to arch/mips/kernel/asm-offsets.c
for v2.6.14.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We were using the native syscall and that results in subtle breakage.

This is the same issue as fixed in 077d0e65
(MIPS: N32: Use compat getsockopt syscall) but that commit did fix it only
for N32.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100291

The L2 cache in the I6400 core has 16 ways, so extend the way_string
array to take such caches into account.

[ralf@linux-mips.org: Other already supported CPUs are free to support
more than 8 ways of cache as well.]
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10640/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Implement the mips_cdmm_phys_base() platform callback to provide a
default Common Device Memory Map (CDMM) physical base address for the
Pistachio SoC. This allows the CDMM in each VPE to be configured and
probed for devices, such as the Fast Debug Channel (FDC).

The physical address chosen is just below the default CPC address, which
appears to also be unallocated.

The FDC IRQ is also usable on Pistachio, and is routed through the GIC,
so implement the get_c0_fdc_int() platform callback using
gic_get_c0_fdc_int(), so the FDC driver doesn't have to fall back to
polling.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: linux-mips@linux-mips.org
Reviewed-by: NAndrew Bresticker <abrestic@chromium.org>
Patchwork: http://patchwork.linux-mips.org/patch/9749/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Wider testing reveals that the Fast Debug Channel (FDC) interrupt is
routed through the GIC just fine on Pistachio SoC, even though it
contains interAptiv cores. Clearly the FDC interrupt routing problems
previously observed on interAptiv and proAptiv cores are specific to the
Malta FPGA bitstreams.

Move the workaround for interAptiv and proAptiv out of
gic_get_c0_fdc_int() in the GIC irqchip driver into Malta's
get_c0_fdc_int() platform callback, to allow the Pistachio SoC to use
the FDC interrupt.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Reviewed-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/9748/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

MT_SMP is not the only SMP option for MT cores. The MT_SMP option
allows more than one VPE per core to appear as a secondary CPU in the
system. Because of how CM works, it propagates the address-based
cache ops to the secondary cores but not the index-based ones.
Because of that, the code does not use IPIs to flush the L1 caches on
secondary cores because the CM would have done that already. However,
the CM functionality is independent of the type of SMP kernel so even in
non-MT kernels, IPIs are not necessary. As a result of which, we change
the conditional to depend on the CM presence. Moreover, since VPEs on
the same core share the same L1 caches, there is no need to send an
IPI on all of them so we calculate a suitable cpumask with only one
VPE per core.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10654/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This reverts commit 6ca716f2.

SMP/CPS is now supported on 64bit cores.

Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10592/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Replace lw/sw and various arithmetic instructions with macros so the
code can work on 64-bit kernels as well.

Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10591/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In preparation for 64-bit CPS support, we replace KSEG0 with CKSEG0
so 64-bit kernels can be supported.

Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10590/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The cps-vec code assumes O32 ABI and uses t4-t7 in quite a few places. This
breaks the build on 64-bit. As a result of which, use the pseudo-registers
ta0-ta3 to make the code compatible with 64-bit.

Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10589/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

mips32r2 is a subset of mips64r2, so we replace mips32r2 with mips64r2
in preparation for 64-bit CPS support.

Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10588/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The PTR_LA macro will pick the correct "la" or "dla" macro to
load an address to a register. This gets rids of the following
warnings (and others) when building a 64-bit CPS kernel:

arch/mips/kernel/cps-vec.S:63: Warning: la used to load 64-bit address
arch/mips/kernel/cps-vec.S:159: Warning: la used to load 64-bit address
arch/mips/kernel/cps-vec.S:220: Warning: la used to load 64-bit address
arch/mips/kernel/cps-vec.S:240: Warning: la used to load 64-bit address
[...]

Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10587/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit 1d8f1f5a ("MIPS: smp-cps: hotplug support") added hotplug
support in the SMP/CPS implementation but it introduced a few build problems
on 64-bit kernels due to pointer being casted to and from 'int' C types. We
fix this problem by using 'unsigned long' instead which should match the size
of the pointers in 32/64-bit kernels. Finally, we fix the comment since the
CM base address is loaded to v1($3) instead of v0.

Fixes the following build problems:

arch/mips/kernel/smp-cps.c: In function 'wait_for_sibling_halt':
arch/mips/kernel/smp-cps.c:366:17: error: cast from pointer to integer of
different size [-Werror=pointer-to-int-cast]
[...]
arch/mips/kernel/smp-cps.c: In function 'cps_cpu_die':
arch/mips/kernel/smp-cps.c:427:13: error: cast to pointer
from integer of different size [-Werror=int-to-pointer-cast]

cc1: all warnings being treated as errors

Fixes: 1d8f1f5a ("MIPS: smp-cps: hotplug support")
Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10586/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit 5f9f41c4 ("MIPS: kernel: Prepare
the JR instruction for emulation on MIPS R6") added support for
emulating the JR instruction on MIPS R6 cores but that introduced a bug
which could be triggered when hitting a JALR opcode because the code used
the wrong field in the 'r_format' struct to determine the instruction
opcode. This lead to crashes because an emulated JALR instruction was
treated as a JR one when the R6 emulator was turned off.

Fixes: 5f9f41c4 ("MIPS: kernel: Prepare the JR instruction for emulation on MIPS R6")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10583/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commits f1b44067 ("MIPS: Emulate the
new MIPS R6 B{L,G}T{Z,}{AL,}C instructions") and commit
a8ff66f5 ("MIPS: Emulate the new MIPS
R6 B{L,G}E{Z,}{AL,}C instructions") added support for emulating various
branch compact instructions. However, it missed the case for those which
use the old BLEZL and BGTZL opcodes leading to random crashes when the R6
emulator is disabled. We fix this by ensuring that the 'rt' field is not
zero which is always true for these branch compact instructions.

Fixes: f1b44067 ("MIPS: Emulate the new MIPS R6 B{L,G}T{Z,}{AL,}C instructions")
Fixes: a8ff66f5 ("MIPS: Emulate the new MIPS R6 B{L,G}E{Z,}{AL,}C instructions")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10582/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix broken indentation caused by the SMTC removal
commit b633648c
("MIPS: MT: Remove SMTC support")
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Fixes: b633648c ("MIPS: MT: Remove SMTC support")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10581/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit f9a7febd leads to a fact that mapstart and therefore a page bitmap for
bootmem allocator immediately follows initrd_end. This doesn't always work
well on Octeon, where there are holes in PFN ranges (refer to 5b3b1688 and
4MB-aligned PFN allocation). Depending on the inird location it could happen,
that mapstart would be in an area not allocated by plat_mem_setup() in
arch/mips/cavium-octeon/setup.c, but in the alignment hole between initrd and
the next PFN area. Later on this memory will be unconditionally made available
to buddy allocator at the end of free_all_bootmem_core() (mm/bootmem.c).
All of this results in Linux using the memory not designated for Linux in
Octeon's plat_mem_setup(), which in turn means corruption of the memory used
by another OS/baremetal code on the same SoC.

It doesn't look to me as a problem of Octeon platform code, but rather as an
inability of f9a7febd to deal correctly with the fragmented memory-mappings.
Proposed fix moves the check for initrd address to the same calculation-loop
in bootmem_init() (arch/mips/kernel/setup.c), which also accounts for kernel
code location. This should result in mapstart located starting from the first
PFN area after kernel code AND initrd.
Signed-off-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: Joe Perches <joe@perches.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Yusuf Khan <yusuf.khan@nokia.com>
Cc: Michael Kreuzer <michael.kreuzer@nokia.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Patchwork: https://patchwork.linux-mips.org/patch/10594/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit 46e12c07 (MIPS: O32 / 32-bit:
Always copy 4 stack arguments.) change the O32 syscall handler to always
load four arguments from the userspace stack even for syscalls that
require fewer or no arguments to be copied.  This removes a large table
from kernel space and need to maintain it.  It appeared that it was ok
the implementation chosen requires 16 bytes of readable stack space
above the user stack pointer.

Turned out a few threading implementations munmap the user stack before
the thread exits resulting in errors due to the unreadable stack.

We now treat any failed load as a if the loaded value was zero and let
the actual syscall deal with the situation.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  CC      arch/mips/loongson64/lemote-2f/clock.o
/home/ralf/src/linux/linux-mips/arch/mips/loongson64/lemote-2f/clock.c:18:40: fatal error: asm/mach-loongson/loongson.h: No such file or directory
 #include <asm/mach-loongson/loongson.h>
                                        ^
compilation terminated.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Nobody used these hooks so they were removed from common code, and can now
be removed from the architectures.
Signed-off-by: NDominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().

Search and conversion was done with coccinelle:

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org

Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().

Search and conversion was done with coccinelle:

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: linux-mips@linux-mips.org

Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().

Search and conversion was done with coccinelle:

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: linux-mips@linux-mips.org

Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().

Search and conversion was done with coccinelle:

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: linux-mips@linux-mips.org

We have confusing functions to clear pmd, pmd_clear_* and pmd_clear.  Add
_huge_ to pmdp_clear functions so that we are clear that they operate on
hugepage pte.

We don't bother about other functions like pmdp_set_wrprotect,
pmdp_clear_flush_young, because they operate on PTE bits and hence
indicate they are operating on hugepage ptes
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently we have many duplicates in definitions of
hugetlb_prefault_arch_hook.  In all architectures this function is empty.
Signed-off-by: NZhang Zhen <zhenzhang.zhang@huawei.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

CRIU is recreating the process memory layout by remapping the checkpointee
memory area on top of the current process (criu).  This includes remapping
the vDSO to the place it has at checkpoint time.

However some architectures like powerpc are keeping a reference to the
vDSO base address to build the signal return stack frame by calling the
vDSO sigreturn service.  So once the vDSO has been moved, this reference
is no more valid and the signal frame built later are not usable.

This patch serie is introducing a new mm hook framework, and a new
arch_remap hook which is called when mremap is done and the mm lock still
hold.  The next patch is adding the vDSO remap and unmap tracking to the
powerpc architecture.

This patch (of 3):

This patch introduces a new set of header file to manage mm hooks:
- per architecture empty header file (arch/x/include/asm/mm-arch-hooks.h)
- a generic header (include/linux/mm-arch-hooks.h)

The architecture which need to overwrite a hook as to redefine it in its
header file, while architecture which doesn't need have nothing to do.

The default hooks are defined in the generic header and are used in the
case the architecture is not defining it.

In a next step, mm hooks defined in include/asm-generic/mm_hooks.h should
be moved here.
Signed-off-by: NLaurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently we have many duplicates in definitions of huge_pmd_unshare.  In
all architectures this function just returns 0 when
CONFIG_ARCH_WANT_HUGE_PMD_SHARE is N.

This patch puts the default implementation in mm/hugetlb.c and lets these
architectures use the common code.
Signed-off-by: NZhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Rientjes <rientjes@google.com>
Cc: James Yang <James.Yang@freescale.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make it similar to the trylock and R10000_LLSC_WAR cases.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9789/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>