If gpio pins from bank[2-5] are marked as wakeup enable and if the wake is
through gpio IO pad wakeup, then that wakeup gpio interrupt is lost.

In the current implementation, GPIO driver stores the context of DATAIN of
all the gpio in the bank. During GPIO resuming, it checks DATAIN with wakeup
enabled pins of gpio bank. If there is status change, then manually toggle
GPIO_LEVELDETECT to generate pseudo interrupt.
Reported-by: NPhilippe Mazet <p-mazet@ti.com>
Tested-by: NPhilippe Mazet <p-mazet@ti.com>
Signed-off-by: NAmbresh K <ambresh@ti.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: NAxel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The Samsung GPIO drivers are always built-in when the relevant
platform is selected.  Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

_set_gpio_triggering uses read-modify-write on bank registers,
lock bank->lock around all calls to it to prevent register
corruption if two cpus access gpios in the same bank at the
same time.
Signed-off-by: NColin Cross <ccross@android.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Setting the IRQWAKEN bit was overwriting previous IRQWAKEN bits,
causing only the last bit set to take effect, resulting in lost
wakeups when the GPIO controller is in idle.

Replace direct writes to IRQWAKEN with MOD_REG_BIT calls to
perform a read-modify-write on the register.
Signed-off-by: NColin Cross <ccross@android.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

WARNING: arch/arm/plat-omap/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_chip_init()
The function __devinit omap_gpio_probe() references
a function __init omap_gpio_chip_init().
If omap_gpio_chip_init is only used by omap_gpio_probe then
annotate omap_gpio_chip_init with a matching annotation.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NKevin Hilman <khilman@ti.com>

After the GPIO driver move, some symbols became selectable when they
shouldn't be.  Tighten the dependencies.
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

We had a few drivers move from arch/arm into drivers/gpio, but they
don't actually compile without the ARM platform headers etc.  As a
result they were messing up allyesconfig on x86.

Make them depend on ARM.
Reported-by: NIngo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

gpio_{request,free}_array should not (and do not) modify the passed gpio
array, so make the parameter const.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Move OMAP GPIO driver to drivers/gpio.  Builds whenever
CONFIG_ARCH_OMAP=y.
Signed-off-by: NKevin Hilman <khilman@ti.com>

GPIO 1 to 8 are added for TPS65911 chip version. The gpio driver
now handles more than one gpio lines. Subsequent versions of the
chip family can add new GPIO lines with minimal driver changes.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The GPIO driver should reside in drivers/gpio/ for better
organization.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Move the Samsung s5pc100 SoC GPIO driver to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Move the Samsung s5pv210 SoC GPIO driver to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Move the Samsung Exynos4 series SoCs GPIO driver to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

It's common gpiolib for recent Samsung SoCs. Move to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NMartin Persson <martin.persson@stericsson.com>
[Split off from larger patch]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Useful to check the status of the runtime pin muxing.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Squashed, modified to use chip-internal IRQ trigger state]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik
and into the desired location indicated by the subsystem
maintainer.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
[grant.likely: squashed with kconfig fixup]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This moves the U300 GPIO driver out of arch/arm/mach-u300 and into
the desired location indicated by the subsystem maintainer.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

While this is essentially a no-op for this driver, it has the
side effect of letting the PMU driver snoop D3 requests from
the PCI core for this driver.

This is only for langwell, not for whitney point.
Signed-off-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

PCA957x is i2c gpio expander, and similar to PCA953x. Although register
configurations are different between PCA957x and PCA953x. They can share
a lot of components, such as IRQ handling, GPIO IN/OUT. So updating PCA953x
driver to support PCA957x chips.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

cs5535-gpio.c has been split into two, with various setup moved
into cs5535-mfd.c.  Given that cs5535-gpio will not load without
the -mfd part, lets make that dependency explicit in Kconfig
Signed-off-by: NEd Wildgoose <kernel@wildgooses.com>
Acked-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.

Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

alpha allmodconfig:

  drivers/gpio/ml_ioh_gpio.c: In function 'ioh_gpio_probe':
  drivers/gpio/ml_ioh_gpio.c:205: error: implicit declaration of function 'kzalloc'
  drivers/gpio/ml_ioh_gpio.c:205: warning: assignment makes pointer from integer without a cast

also fix this:

  drivers/gpio/ml_ioh_gpio.c:145: warning: 'ioh_gpio_save_reg_conf' defined but not used
  drivers/gpio/ml_ioh_gpio.c:154: warning: 'ioh_gpio_restore_reg_conf' defined but not used

Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

alpha allmodconfig:

  drivers/gpio/vx855_gpio.c: In function 'vx855gpio_probe':
  drivers/gpio/vx855_gpio.c:233: error: implicit declaration of function 'kzalloc'
  drivers/gpio/vx855_gpio.c:233: warning: assignment makes pointer from integer without a cast

Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow GPIO_BASIC_MMIO_CORE to be used to provide an accessor library
for implementing GPIO drivers whilst abstracting the register access
detail.  Based on a patch from Anton Vorontsov[1] and adapted to allow
bgpio_chip to be embedded in another structure.

Changes since v1:
	- Register the gpio_chip in the platform device probe

1. https://lkml.org/lkml/2011/4/19/401Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The build files for drivers/gpio has some wording and comments
about the directory being reserved exclusively for GPIO expanders
(according to the gpio.txt file these are on external busses) and
this has been false for some time. We already have PL061 and
Xilinx drivers which are in silicon and now I'm moving more
silicon drivers here, so delete this and reword it a bit.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch allows to trace gpio operations using ftrace
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Make pca953x driver use the simple irq handler since no hardware control
is necessary and the driver lacks an irq_ack function. handle_edge_irq()
calls chip->irq_ack() which crashes since this function does not exist.
Signed-off-by: NErik Botö <erik.boto@pelagicore.com>
Signed-off-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Export function gpiochip_find so that modules can use it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Since all the drivers are in a 'if GPIOLIB/endif block', the depends on GPIOLIB
is redundant so remove them.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The __raw_* accessors don't include memory barriers and can cause
problems when writes get stuck in write buffers.
Suggested-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Most controllers require the direction of a GPIO to be set by writing to
a direction register.  Add support for either an input direction
register or an output direction register.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Some controllers have separate input and output registers.  For these
controllers, use "set" for the output and "dat" for the input.

Changes since v2: reuse "set" for output and "dat" for input rather than
adding a new "in" register.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Rather than detecting the output method each time in the .set()
callback, do it at probe time and set the appropriate callback.

Changes since v2: moved the reg_dat initialization into
bgpio_setup_io().
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>