On some SoCs (like exynos5250) you need to use an external GPIO for
write protect.  Add support for wp-gpios to the core dw_mmc driver
since it could be useful across multiple SoCs.

With this change I am able to make use of the write protect for the
external SD slot on exynos5250-snow.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NChris Ball <cjb@laptop.org>

The "disable-wp" property is used to specify that a given SD card slot
doesn't have a concept of write protect.  This eliminates the need for
special case code for SD slots that should never be write protected
(like a micro SD slot or a dev board).

The dw_mmc driver is special in needing to specify "disable-wp"
because the lack of a "wp-gpios" property means to use the special
purpose write protect line.  On some other mmc devices the lack of
"wp-gpios" means that write protect should be disabled.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NChris Ball <cjb@laptop.org>

ctype is using 1-bit buswidth mode by default.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

To ensure the stable clock need to enable before set the
DW_MMC_CARD_NEED_INIT flag.  If set DW_MMC_CARD_NEED_INIT flag,
wait for 80-clock before first command after power-up.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use managed device resource functions for easy handling.
This makes driver simpler in the routine of error and exit.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add dt-based retrieval of host sdio pm capabilities. Based on
the dt based discovery do a bus init in the resume function.
Signed-off-by: NOlof Johansson <olofj@chromium.org>
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The patch "dw_mmc: fix multiple drv_data NULL dereferences" has
unfortunately clashed with my "mmc: dw_mmc: constify dw_mci_idmac_ops
in exynos back-end" patch, causing new warnings to appear.

This should hopefully fix the issue for good.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The of_device_id match data is now marked as const and
must not be modified. This changes the dw_mmc to mark
all pointers passing the dw_mci_drv_data or dw_mci_dma_ops
structures as const, and also marks the static definitions
as const.

drivers/mmc/host/dw_mmc-exynos.c: In function 'dw_mci_exynos_probe':
drivers/mmc/host/dw_mmc-exynos.c:234:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

800d78bf ("mmc: dw_mmc: add support for implementation specific
callbacks") -- merged in v3.7-rc1 -- introduced multiple NULL pointer
dereferences when the default dw_mci_pltfm_probe() is used, as it sets
host->drv_data to NULL, and that's only checked against NULL in 1 out of
the 7 cases where it is dereferenced.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

As mmc_start_host is getting called before enabling the dw_mmc controller
interrupt, there is a problem of missing the SDMMC_INT_CMD_DONE for the
very first command sent by the sdio_reset.

This problem occurs only when we disable MMC debugging i.e, MMC_DEBUG=n.
This patch enables the dw_mmc controller interrupt before mmc_start_host.
Signed-off-by: NYuvaraj CD <yuvaraj.cd@samsung.com>
Reviewed-by: NGirish K S <girish.shivananjappa@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch removes the following warning.
drivers/mmc/host/dw_mmc.c:1976: warning: passing argument 1 of
'_dev_info' from incompatible pointer type
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes up the broken suspend sequence for eMMC with sleep
support. Additionally it reworks the eMMC4.5 Power Off Notification
feature so it fits together with the existing sleep feature.

The CMD0 based re-initialization of the eMMC at resume is re-introduced
to maintain compatiblity for devices using sleep.

A host shall use MMC_CAP2_POWEROFF_NOTIFY to enable the Power Off
Notification feature. We might be able to remove this cap later on,
if we think that Power Off Notification always is preferred over
sleep, even if the host is not able to cut the eMMC VCCQ power.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NSaugata Das <saugata.das@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This reverts commit 94c6cee9 (Add check for IDMAC configuration).
Synopsys says that only if internal dmac is not present, optional
external dma interface is present. When internal dmac is present,
'0' value in DMA_INTERFACE of HCON is reasonable. DMA_INTERFACE
indicates external dma interface. And idmac initialization is
prohibited now.

The commit should be reverted since: the check for IDMAC is not
reliable; falling back to PIO would provide awful performance; we
wouldn't expect to see instances of this block without DMA support.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The core dw-mshc controller driver can let platform specific
implementations of the dw-mshc controller to control the hardware
as required by such implementations. This is acheived by invoking
implementation specific (optional) callbacks. Define the list of
callbacks supported the add invocation points for the same.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add device tree based discovery support.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If the write protect pad of the controller is not connected to the write
protect pin of the slot, the driver should be notified of this condition
so that incorrect check for write protection by reading the WRTORT
register can avoided. The get_ro platform callback can be used for in
such cases, but with device tree support enabled, such platform callbacks
cannot be supported.

Add a new quirk for notifying the driver about the missing write protect
line so the driver can assume that the card write protection is disabled.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some platforms allow for clock gating and control of bus interface unit
clock and card interface unit clock. Add support for clock lookup of
optional biu and ciu clocks for clock gating and clock speed
determination.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Instead of aborting the probe when a slot initialization fails, allow
initialization of as many slots as possible. If there is at least one
instance of a slot that is successfully initialized, allow the driver
probe to succeed.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The 'struct dw_mci' maintains a copy of the pdev->dev instance instead of
maintaining a reference to that 'struct device' instance. Any resource
allocated using the device resource management kernel API with the instance
of 'struct device' in 'struct dw_mci' is then incorrect. Fix this by
converting the copy of 'struct device' in 'struct dw_mci' to a reference.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fixed the below message.

WARNING: drivers/mmc/host/built-in.o(.text+0x5ee8): Section mismatch in reference from the function dw_mci_probe() to the function .init.text:dw_mci_init_slot()
The function dw_mci_probe() references
the function __init dw_mci_init_slot().
This is often because dw_mci_probe lacks a __init
annotation or the annotation of dw_mci_init_slot is wrong
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The documentation for the dw_mmc part says that the low power
mode should normally only be set for MMC and SD memory and should
be turned off for SDIO cards that need interrupts detected.

The best place I could find to do this is when the SDIO interrupt
was first enabled.  I rely on the fact that dw_mci_setup_bus()
will be called when it's time to reenable.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Data transfer will be continued until all the bytes are transmitted,
even if data crc error occurs during a multiple-block data transfer.
This means RXDR/TXDR interrupts will occurs until data transfer is
terminated. Early setting of host->sg to NULL prevents going into
xxx_data_pio functions, hence permanent unhandled RXDR/TXDR interrupts
occurs. And checking error interrupt status in the xxx_data_pio functions
is no need because dw_mci_interrupt does do the same. This patch also
removes it.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Datasheet of SYNOPSYS mentions that DTO(Data Transfer Over) interrupt
will be raised even if some error interrupts, however it is actually
found that DTO does not occur. SYNOPSYS has confirmed this issue.
Current implementation defers the call of tasklet_schedule until DTO
when the error interrupts is happened. This patch fixes error handling.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

RINTSTS status includes masked interrupts as well as unmasked.
data_status and cmd_status are set by value of RINTSTS in interrupt handler
and tasklet finally uses it to decide whether error is happened or not.
In addition, MINTSTS status is used for setting data_status in PIO.
Masked error interrupt will not be handled and that status can be considered
non-error case.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed By: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

host->dma_ops is not valid if host->usa dma is 0 so protect
host->dma_ops reference in dw_mci_resume
Signed-off-by: NJonathan Kliegman <kliegs@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In the current dwmmc driver there is support for selecting IDMAC from
the menu config option. If the support for IDMAC is enabled in the menu
config and the hardware configuration register's DMA_INTERFACE field is
0, the driver will still try to do the DMA initialization.

The dw_mci_idmac_init function currently implemented returns only success
indicating that the DMA initialization is always successful. This patch
adds a check for existence of the DMA IP to allow the DMA initialization.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In case of "host->bus_hz < slot->clock", divider value is
miscalculated. And clock divider register value is multiple of 2. If
calculated divider value is odd number, result can be over-clocking.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Setting host->data to NULL is incorrect sequence in
dw_mci_command_complete. This early setting makes the skip of
dma_unmap_sg in dw_mci_dma_cleanup.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

IDMAC may not be cleaned in driver probe if it has been already used in
boot time. So IDMAC needs sw reset newly. And DMA interface reset
precedes the internal DMAC reset. Additionally SDMMC_IDMAC_SWRESET is
replaced with magic code.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

DTO interrupt can be later than transmit interrupt(IDMAC) in case of
write. Current handling of IDMAC interrupt sets EVENT_DATA_COMPLETE as
well as EVENT_XFER_COMPLETE regardless of DTO rising. This makes the
current request finish in tasklet and permits the next request even
though current data transfer is still in progress. As a result, sequence
is broken and lock-up happens. Setting EVENT_DATA_COMPLETE is not proper
after IDMAC interrupt. It should be taken after DTO interrupt is
generated.
Reported-by: NDmitry Shmidt <dimitrysh@android.com>
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NHyeonsu Kim <hyeonsu.kim@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The sdio interrupt mask bits are arranged in [31:16].
(1 << SDMMC_INT_SDIO(slot->id))) does 16 bits left shift twice.
So this patch changes to do 16 bits left shift only one time.
Signed-off-by: NKyoungil Kim <ki0351.kim@samsung.com>
Acked-by: NShashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The variable 'dw_mci_card_workqueue' is a global variable shared between
multiple instances of the dw_mmc host controller. Due to this, data
corruption has been noticed when multiple instances of dw_mmc controllers
are actively reading/writing the media. Fix this by adding a instance
of 'struct workqueue_struct' for each host instance and removing the
global 'dw_mci_card_workqueue' instance.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Now, dma_ops is assumed that use the IDMAC.  But if dma_ops is assigned
the pdata->dma_ops, we didn't ensure that callback function is defined.

If the callback isn't defined, then we should run in PIO mode.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

When dw_mci_pre_dma_transfer returns failure in some reasons,
dw_mci_submit_data will prepare to switch the PIO mode from DMA.
After switching to PIO mode, DMA(IDMAC in particular) is still
enabled. This makes the corruption in handling interrupt and
the driver lock-up.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

3ec7699d3bb1b0ee7 ("mmc: dw_mmc: Add support for pre_req and post_req")
broke non-IDMAC DMA, because dw_mci_pre_dma_transfer() is valid only if
using internal DMA. In case of using other DMA it returns -ENOSYS. It
prevents the DMA operations.  This patch makes dw_mci_pre_dma_transfer()
effective in all DMA cases again.
Reported-by: NJames Hogan <james@albanarts.com>
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

When disable CONFIG_MMC_DW_IDMAC, can see the compiler error.
Because in dw_mci_post_req(), called the dw_mci_get_dma_dir().
But that function is in #ifdef CONFIG_MMC_DW_IDMAC.

I think that function is generic function.
Not need the CONFIG_MMC_DW_IDMAC.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In CLKENA register, can support 16-SD card clocks.
If support correctly, must shift with slot-id.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch implements pre_req and post_req in dw_mmc to support
asynchronous mmc request.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

When use the IDMAC, we can also want to use the pdata->blk-setting.
So if pdata->blk-setting is unset, use the default value.
if not, use the pdata->blk-setting.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Support of PCI mode for the dw_mmc driver. This Patch adds the
support for the scenario where the Synopsys Designware IP
is present on the PCI bus. The patch adds the minimal modifications
necessary for the driver to work on PCI platform. Also added separate
files for PCI and PLATFORM modes of operation.
Signed-off-by: NShashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>