In these configuration we expect to have large amounts of memory (> 4G)
and thus will bounce via swiotlb some region of PCI address space.

The outbound windows were wasting 512M of address space by leaving a
gap between the top of the outbound window and the 4G boundary.  By
moving the top of the outbound window up to the 4G boundary we can
reclaim the vast majority of the 512M (minus space needed for PEXCSRBAR)
and thus reduces the amount of memory we have to bounce.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Its feasible based on how the PCI address map is setup that the region
of PCI address space used for MSIs differs for each PHB on the same SoC.

Instead of assuming that the address mappes to CCSRBAR 1:1 we read
PEXCSRBAR (BAR0) for the PHB that the given pci_dev is on.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The MPC8568/9 chips support MSIs on PCIe so no reason not to enable them.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

We we build with dma_addr_t as a 64-bit quantity we get:

drivers/dma/fsldma.c: In function 'fsl_chan_xfer_ld_queue':
drivers/dma/fsldma.c:625: warning: cast to pointer from integer of different size
drivers/dma/fsldma.c: In function 'fsl_dma_chan_do_interrupt':
drivers/dma/fsldma.c:737: warning: cast to pointer from integer of different size
drivers/dma/fsldma.c:737: warning: cast to pointer from integer of different size
drivers/dma/fsldma.c: In function 'of_fsl_dma_probe':
drivers/dma/fsldma.c:927: warning: cast to pointer from integer of different
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NDan Williams <dan.j.williams@intel.com>

For serial flash support we need to:

- Add QE Par IO Bank E device tree node, a GPIO from this bank is
  used for SPI chip-select line;
- Add serial-flash node;
- Add proper module alias into of/base.c.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Note that eSDHC and DUART0 are mutually exclusive on MPC8569E-MDS
boards. Default option is DUART0, so eSDHC is disabled by default.
U-Boot will fixup device tree if eSDHC should be used instead of
DUART0.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch fixes bogus reg = <> property in the localbus node,
and fixes interrupt property (should be "interrupts").

Also add node for NAND support.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

fsl,exec-units-mask should be 0xbfe to include SNOW unit in
MPC8569E's security engine.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds PCI IDs for MPC8569 and MPC8569E processors,
plus adds appropriate quirks for these IDs, and thus makes
PCI-E actually work on MPC8569E-MDS boards.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Between the addition of the ecm/mcm law nodes and the fact that the
get_immrbase() has been using the range property of the SoC to determine
the base address of CCSR space we no longer need the reg property at
the soc node level.  It has been ill specified and varied between device
trees to cover either the {e,m}cm-law node, some odd subset of CCSR
space or all of CCSR space.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add fsl,qe-num-riscs and fsl,qe-num-snums to all the devices trees which
have qe node.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The MPC8569 is similiar to the MPC8568.  It doubles the number of
QUICC Engine RISC cores from 2 to 4.  Removes eTSECs, TLU and adds
the eSDHC controller.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

In the case the QE has 46 SNUMs for the threads to support four UCC
Ethernet at 1000Base-T simultaneously.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The latest QE chip may have more Serial Number(SNUM)s of thread to use. We
will get the number of SNUMs from device tree by reading the new property
"fsl,qe-num-snums", and set 28 as the default number of SNUMs so that it is
compatible with the old QE chips' device trees which don't have this new
property. The macro QE_NUM_OF_SNUM is defined as the maximum number in QE
snum table which is 256.

Also we update the snum_init[] array with 18 more new SNUMs which are
confirmed to be useful on new chip.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Change the definition of riscTx and riscRx to unsigned integer instead of
enum, and change their values to support 4 risc allocation if the qe has
4 RISC engines.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Change the RISC allocation to macros instead of enum, add function to read
the number of risc engines from the new property "fsl,qe-num-riscs" under
the qe node in dts. Add new property "fsl,qe-num-riscs" description in
qe.txt
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Keep an unique machine def for the MPC8568 MDS board to handle some
subtle differences between the future MDS board. Also set the bcsrs in
setup_arch() only for mpc8568_mds because other mds has different bcsr
settings.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Removed the need for asm/mpc86xx.h as it was only used in mpc86xx_smp.c
and just moved the defines it cared about into there.  Also fixed up
the ioremap to only map the one 4k page we need access to and to iounmap
when we are done.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Kill of some old defines and macros that we no longer use like
CPM_MAP_ADDR and CPM_IRQ_OFFSET.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Also, convert them to resource_size_t (which is unsigned long
on 64-bit, so it's not a change there).

We will be using these on fsl 32b to indicate the start and size
address of memory that the pci controller can actually reach - this
is needed to determine if an address requires bounce buffering.  For
now, initialize them to a standard value; in the near future, the
value will be calculated based on how the inbound windows are
programmed.
Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org>
Acked-by: NBen Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The first 4k region of CCSR space is well defined for local access
windows, CCSRBAR, etc.  The second 4k region is well defined as
register for configuring and getting errors for the MPX coherency
module.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The first 4k region of CCSR space is well defined for local access
windows, CCSRBAR, etc.  The second 4k region is well defined as
register for configuring and getting errors for the ECM coherency
module.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The rstcr register mapping code was written sometime ago before
of_iomap() existed.  We can use it and clean up the code a bit
and get rid of one user of get_immrbase() in the process.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The new dts places most of the devices in physical address space
above 32-bits, which allows us to have more than 4GB of RAM present.
Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Refactor the check to determine if the quirk is applicable to the boards
into one inline function so we only have to change one place to add more
boards that the quirks might be applicable to.

Also removed a warning related to unused temp variable.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The cell-index property isn't used on PCI nodes and is ill defined.
Remove it for now and if someone comes up with a good reason and
consistent definition for it we can add it back
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

It's still in the git history if anyone wants it.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: check sysdev_suspend(PMSG_FREEZE) return value

This adds CONFIG_REISERFS_FS_XATTR protection from reiserfs_permission.

This is needed to avoid warnings during file deletions and chowns with
xattrs disabled.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This avoids an Oops in open_xa_root that can occur when deleting a file
with xattrs disabled.  It assumes that the xattr root will be there, and
that is not guaranteed.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With xattr cleanup even with xattrs disabled, much of the initial setup
is still performed.  Some #ifdefs are just not needed since the options
they protect wouldn't be available anyway.

This cleans those up.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  mm: SLOB fix reclaim_state
  mm: SLUB fix reclaim_state
  slub: add Documentation/ABI/testing/sysfs-kernel-slab
  slub: enforce MAX_ORDER

Ian Campbell noticed that since "Eliminate thousands of warnings with
gcc 3.2 build" (commit 57adc4d2) all
WARN_ON()'s currently appear to come from warn_slowpath_null(), eg:

  WARNING: at kernel/softirq.c:143 warn_slowpath_null+0x1c/0x20()

because now that warn_slowpath_null() is in the call path, the
__builtin_return_address(0) returns that, rather than the place that
caused the warning.

Fix this by splitting up the warn_slowpath_null/fmt cases differently,
using a common helper function, and getting the return address in the
right place.  This also happens to avoid the unnecessary stack usage for
the non-stdargs case, and just generally cleans things up.

Make the function name printout use %pS while at it.

Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  piix: The Sony TZ90 needs the cable type hardcoding
  icside: register second channel of version 6 PCB
  ide-tape: remove back-to-back REQUEST_SENSE detection

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: Idle C-states disabled by max_cstate should not disable the TSC
  ACPI: idle: fix init-time TSC check regression
  ACPI processor: reset the throttling state once it's invalid
  ACPI processor: introduce module parameter processor.ignore_tpc
  ACPI, i915: build fix
  ACPI: suspend: restore BM_RLD on resume
  ACPI: resume: re-enable SCI-enable workaround
  thermal: fix off-by-1 error in trip point trigger condition
  eeepc-laptop: unregister_rfkill_notifier on failure
  asus-laptop: fix input keycode
  eeepc-laptop: support for super hybrid engine (SHE)
  eeepc-laptop: Work around rfkill firmware bug
  eeepc-laptop: report brightness control events via the input layer
  eeepc-laptop: fix wlan rfkill state change during init
  ACPI: suspend: don't let device _PS3 failure prevent suspend
  ACPI: power: update error message
  ACPI: video: DMI workaround another broken Acer BIOS enabling display brightness
  ACPICA: use acpi.* modparam namespace
  ACPI video: dmi check for broken _BQC on Acer Aspire 5720

The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Reported-by: NJonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The second IDE channel of version 6 PCB is not being registered anymore since
the commit 48c3c107 (ide: add struct ide_host
(take 3)).
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>