Noticed when doing the audio support for the Pinnacle PCTV HD Ultimate 808e
that the modes were incorrect (the 808e uses I2S in 5 sample mode)

Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Like the em2874, the em2870 does not have any analog support, so don't bother
loading the em28xx-alsa module.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Pinnacle 80e cannot be supported since Micronas yanked their driver
support for the drx-j chipset at the last minute.  Remove the device profile
since it cannot work without the drx driver and it being there is only likely
to confuse people into thinking the device is supported but not working.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The DVC 100 profile is redundant since we already have an existing identical
profile named "Pinnacle Dazzle DVC 90/DVC 100"
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Correct problem introduced during the board refactoring where the XCLK
frequency would get zero'd out.  The sequence of events was as follows:

em28xx_pre_card_setup() called em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration
em28xx_pre_card_setup() would set the dev->board.xclk if not set
em28xx_pre_card_setup() would set the XCLK register based on dev->board.xclk
...
em28xx_card_setup() would call em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration (clearing out
 value of dev->board.xclk set in em28xx_pre_card_setup)
...
em28xx_audio_analog_set() sets the XCLK register based on dev->board.xclk
 (which now contains zero)

The change sets the default XCLK and I2C Clock fields in the board definition
inside of em28xx_set_model() so that subsequent calls do not cause the
values to be overwritten.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix this warning:

drivers/media/video/zoran/zoran_card.c:156: warning: ‘zr36067_pci_tbl’ defined but not used

Currently, zoran driver relies on a find routine that doesn't use the
pci table.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/dvb/frontends/af9013.c: In function ‘af9013_set_coeff’:
drivers/media/dvb/frontends/af9013.c:231: warning: ‘ns_coeff2_8k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:230: warning: ‘ns_coeff2_2k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:229: warning: ‘ns_coeff1_8193nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:228: warning: ‘ns_coeff1_8192nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:227: warning: ‘ns_coeff1_8191nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:226: warning: ‘ns_coeff1_2048nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_update_snr’:
drivers/media/dvb/frontends/af9013.c:1012: warning: ‘snr_table’ may be used uninitialized in this function

Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is needed to sync with the development tree. Probably, a merge
conflict were solved by adding this blank line.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/usbvideo/quickcam_messenger.c: In function ‘qcm_sensor_init’:
drivers/media/video/usbvideo/quickcam_messenger.c:450: warning: operation on ‘ret’ may be undefined
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes this warning:

drivers/media/video/gspca/gspca.c:1811: warning: initialization from incompatible pointer type

The reason is that the returned argument should be a long, not an
integer.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/dvb/dvb-usb/anysee.c: In function ‘anysee_master_xfer’:
drivers/media/dvb/dvb-usb/anysee.c:156: warning: ‘ret’ may be used uninitialized

By looking at the function, altrough very unlikely, this might
eventually be true if num  = 0. So, better to fix the warning by
initializing with ret = 0.

Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Extend the range of supported UVC devices by allowing video output devices
matching the following structure:

TT_STREAMING -> VC_PROCESSING_UNIT -> VC_EXTENSION_UNIT{0,n} -> OTT_*

Video output devices are reported with the V4L2_CAP_VIDEO_OUTPUT capability
flag and are subject to the same restrictions as video input devices.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Built-in iSight webcams have an interrupt endpoint but spit proprietary data
that don't conform to the UVC status endpoint messages. Don't try to handle
the interrupt endpoint for those cameras.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When the first bulk URB of a video payload contains an erroneous header, or
when no V4L2 buffer is available, the whole payload must be dropped. Change
the skip logic to drop all bulk URBs until the end of the payload instead of
the first one only.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This camera is rather similar to MT9M001, but also has a couple of
enhanced features, like pixel binning.

 create mode 100644 drivers/media/video/mt9t031.c
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Don't modify driver's state in try_fmt, just verify format acceptability
or adjust it to driver's capabilities.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

priv->scale is checked in start_capture.
Therefore, it should be NULL if failing in set_fmt.
This patch resolve this problem.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds tw9910 driver that use soc_camera framework.
It was tested on SH Migo-r board and mplayer.

 create mode 100644 drivers/media/video/tw9910.c
 create mode 100644 include/media/tw9910.h
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In preparation for i.MX31 camera host driver add flags for 4 and 15 bit bus
widths and for data lines polarity inversion.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

sh_mobile_ceu_camera.c is already prepared to support interlaced format, this
patch moves the choice of a field type down to host and / or camera drivers.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch cleans up the sh_mobile_ceu driver and adds comments and
constants to clarify the magic sequence in sh_mobile_ceu_capture().
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch presents new method to be able to select V4L2 input type
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch presents new method to be able to check v4l2_std_id
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds NV16/NV61 support to the sh_mobile_ceu driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds NV12/NV21 support to the sh_mobile_ceu driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move mutex from host drivers to camera device object, take into account
videobuf locking.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With the introduction of the format conversion support in soc-camera, we now
also have to take care to pass the correct pixel format to the camera driver
when calling its try_fmt() method.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Simplify multiple drivers by replacing f->fmt.pix.* with a single pointer
dereference, merge some needlessly broken lines, verify host and camera
operations pointers on registration.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch converts the sh_mobile_ceu driver to make use
of the new pixel format translation code. Only pass-though
mode at this point.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for NV16 and NV61 pixel formats.

These pixel formats use two planes; one for 8-bit Y values and
one for interleaved 8-bit U and V values. NV16/NV61 formats are
very similar to NV12/NV21 with the exception that NV16/NV61 are
using the same number of lines for both planes. The difference
between NV16 and NV61 is the U and V byte order.

The fourcc values are extrapolated from the NV12/NV21 case.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The chip is largely compatible with MT9M111 and is going to be supported by the
same driver.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Using PXA270's FIFO inactivity time-out register (CITOR) reduces FIFO overruns.
The time-out is calculated in CICLK / LCDCLK ticks and has to be longer than
one pixel time. For this we have to know the pixel clock frequency, which
usually is provided by the camera. We use the struct soc_camera_sense to
request PCLK frequency from the camera driver upon each data format change.
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a struct soc_camera_sense, that can be used by camera host drivers to
request additional information from a camera driver, for example, when
changing data format. This struct can be extended in the future, its first use
is to request the camera driver whether the pixel-clock frequency has changed.
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>