Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Due to a HW issue, our current scheme to transition the connection from
streaming to rdma mode is broken on the passive side.  The firmware
and driver now support a new transition scheme for the passive side:

 - driver posts rdma_init_wr (now including the initial receive seqno)
 - driver posts last streaming message via TX_DATA message (MPA start
   response)
 - uP atomically sends the last streaming message and transitions the
   tcb to rdma mode.
 - driver waits for wr_ack indicating the last streaming message was ACKed.

NOTE: This change also bumps the required firmware version to 4.3.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested.  In
other words, this means that the following race is possible:

	while (CQ is not empty)
		ib_poll_cq(CQ);
	// new completion is added after while loop is exited
	ib_req_notify_cq(CQ);
	// no event is generated for the existing completion

To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.

However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification).  Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.

Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:

	 < 0	means an error occurred while requesting notification
	== 0	means notification was requested successfully, and if
		IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
		events were missed and it is safe to wait for another
		event.
	 > 0	is only returned if IB_CQ_REPORT_MISSED_EVENTS was
		passed in.  It means that the consumer must poll the
		CQ again to make sure it is empty to avoid the race
		described above.

We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This was spotted by the Coverity checker (CID 1554).
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

cxgb3 uses dma_alloc_coherent() et al. thus needs linux/dma-mapping.h
include in order to build reliably.

Noticed on sparc64.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- don't mark static functions in C files as inline - gcc should know
  best whether inlining makes sense
- never compile the unused cxio_dbg.c
- make the following needlessly global functions static:
  - cxio_hal.c: cxio_hal_clear_qp_ctx()
  - iwch_provider.c: iwch_get_qp()
- remove the following unused global functions:
  - cxio_hal.c: cxio_allocate_stag()
  - cxio_resource.: cxio_hal_get_rhdl()
  - cxio_resource.: cxio_hal_put_rhdl()
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove the Open Grid Computing copyright.  It shouldn't be there.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add an RDMA/iWARP driver for the Chelsio T3 1GbE and 10GbE adapters.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>