Instead of having two memory configuration sets, one for wl127x and
one for wl128x, we can use only one which should be correctly set by
the lower driver.

The wl12xx driver now uses the wl128x memory config by default but
changes it when if it identifies the wl127x chips.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The extended radio configuration parameters are only used by the
wl127x chipsets, which are handled by the wl12xx driver.  Move the rf
configuration settings from wlcore to wl12xx.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The configuration parameters vary with different chip families.  Some
of the parameters used only by some chip families, others should have
different value depending on the family.  Thus move the configuration
values from wlcore to wl12xx.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Change the cmd_trigger op to include the write of the command buffer.

Also, instead of letting the lower driver access the cmd_box_addr element
directly, we now pass the address in the trigger_cmd operation, so it
doesn't have to be exported.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add an op for family-specific vif initialization.  Currently unused,
but will be needed when wl18xx support is implemented.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move all the wl12xx-specific hw initialization procedures into a new
hw_init op.  Move some commands and ACX functions to wl12xx.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Inverting the quirk flag to indicate Tx-alignment. This aligns it with
the similar Rx-side quirk.

The call to wl1271_set_block_size() decides whether SDIO block size
alignment can be used or not.  In case we're using SPI, we can't use
the block size alignment, so the function returns false.  So we set
the quirk when wl1271_set_block_size() returns true and let the wl12xx
lower driver unset the bit for wl127x (since it doesn't support this
quirk).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

One chip family employs immediate Tx completion, where knowledge of
completed packets is given as part of the FW status. Another is only
notified of Tx completion via the FW status, and has to read the
completion status of the packets from a different location.

Implement the wl12xx tx completion as a delayed Tx completion.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

There is a difference in the way chip families report the length of data
in a single Rx packet. Abstract this into a HW op. Refactor the Rx data
handling function to allocate the correct size for the data, and avoid
trimming the skb.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The only difference in the read_data operations is that some chips
need to prepare the data to be read before reading.  So instead of
having a mandatory read_data operation, we now have an option
prepare_data operation that only needs to be implemented for chips
that require it.

In the wl12xx lower driver, we only set the prepare_data operation for
wl127x chips.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

An aligned data buffer is such where the Ethernet portion of the packet
starts on a 4-byte boundary. Some chip families support padding the Rx
data buffer to achieve such alignment, others rely on the host to perform
it.
Implement the HW op for getting alignment state in wl12xx. Add
support for HW-padded alignment in the Rx flow.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

For chip-families that support aligned buffers in the Rx side. The Rx
flow changes slightly for these chips.

Currently these modifications rely on a hard-coded block-size of 256.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Rates reported by HW can be different between chip families. Make the
rate-to-idx translation tables private per family and use them in a
common translation function. Add a global element to help determine
which rates are HW HT-rates.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Each chip family indicates the length of a frame to the HW differently.
This includes different padding, alignment and other fields in the HW Tx
descriptor.

Put all wl12xx specific code in a hw op.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Each chip family has a slightly different Tx descriptor. Set the
descriptor values according to family.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Each chip family has a different block size and calculates the total
number of HW blocks differently, with respect to alignment.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The number of spare Tx blocks must be changed when the GEM cipher is
engaged. Track set_key() operations to see if this is the case and
change the Tx HW spare block count accordingly. Set the number of spare
blocks for each operating mode from the low level driver.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Each chip family can have a different amount of Tx descriptors. These
are set on init.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This storage is allocated in wlcore_alloc_hw and freed in free_hw. The
size of the storage is determined by the low-level driver.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

ELP is a very complicated process in the firmware.  Due to its
complexity, in some early firmware revisions, the ELP feature is
disabled.  To support this cases, this patch adds a quirk that
disables ELP mode.

When ELP is not supported, do not attempt to enter ELP when requested by
the driver.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We were reading the even mailbox address three times, which was
completely unnecessary and complicated things regarding partition
selection.  Remove the unnecessry reads and set the address for
mailbox 1 and 2 after the first read.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Instead of checking the chip ID directly in the wlcore code to decide
whether to use the new or the old NVS format, we now use a quirk that
should be set by the low level driver to say that it needs to use the
old format.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Different chips may use different bits in the interrupt trigger
register.  Add operations to handle these differences.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Different chip families have the factory MAC address written in
different places.  Add a new hardware operation to read the MAC
address, if available.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The top registers initialization is very specific to the actual
hardware used, even the way in which we read from and write to the top
registers varies from chip to chip.  This patch moves all top
registers initialization to wl12xx.  Also add a boot op for the wlcore
module to call at the right time and a few callbacks with the common
called to be called from the lower drivers boot operations.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The PG version depends on the actual hardware.  This commit moves the
code used to read the PG version to the lower driver, by adding the
get_pg_ver hardware operation.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move the code that identifies the chip ID and selects the appropriate
firmware to an operation implemented by the lower driver.  Also move
the quirks definitions into wlcore.h and rename to WLCORE_QUIRK_*.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add register tables support in wlcore, add some new IO functions to
read and write to chip-specific register and data addresses.  Move
some common register values from wl12xx to wlcore and add the
registers table to wl12xx.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add partition tables to wlcore, move and reorganize partition setting
functions.  Move wl12xx partition table to use the wlcore partition
table instead.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In order to add chip-specific operations and prepare for future
elements that need to be set by the lower driver, move the wl1271
structure to the wlcore.h file and add an empty placeholder for the
operations structure.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We need to set some parameters (eg. partition and register tables)
during probe of the lower driver, so split the probe function, leaving
most of it in wlcore, but moving the hw struct allocation to the lower
driver.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Create a new small wl12xx module that only contains the probe
functions and depends entirely on wlcore otherwise.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Rename the wl12xx driver directory to wlcore as an initial step
towards the split of the driver into wlcore and wl12xx.  We just
rename the directory first to keep git blame happy.
Signed-off-by: NLuciano Coelho <coelho@ti.com>