My patch moving ppc64 RTC to genrtc was supposed to update all
defconfigs, but for some reason, the patch actually posted only had the
pseries one... ouch. This patch properly updates all defconfigs.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently 8xx fails to boot due to endless pagefaults.

Seems the bug is exposed by the change which avoids flushing the
TLB when not necessary (in case the pte has not changed), introduced
recently:

__handle_mm_fault():

        entry = pte_mkyoung(entry);
        if (!pte_same(old_entry, entry)) {
                ptep_set_access_flags(vma, address, pte, entry, write_access);
                update_mmu_cache(vma, address, entry);
                lazy_mmu_prot_update(entry);
        } else {
                /*
                 * This is needed only for protection faults but the arch code
                 * is not yet telling us if this is a protection fault or not.
                 * This still avoids useless tlb flushes for .text page faults
                 * with threads.
                 */
                if (write_access)
                        flush_tlb_page(vma, address);
        }

The "update_mmu_cache()" call was unconditional before, which caused the TLB
to be flushed by:

        if (pfn_valid(pfn)) {
                struct page *page = pfn_to_page(pfn);
                if (!PageReserved(page)
                    && !test_bit(PG_arch_1, &page->flags)) {
                        if (vma->vm_mm == current->active_mm) {
#ifdef CONFIG_8xx
                        /* On 8xx, cache control instructions (particularly 
                         * "dcbst" from flush_dcache_icache) fault as write 
                         * operation if there is an unpopulated TLB entry 
                         * for the address in question. To workaround that, 
                         * we invalidate the TLB here, thus avoiding dcbst 
                         * misbehaviour.
                         */
                                _tlbie(address);
#endif
                                __flush_dcache_icache((void *) address);
                        } else
                                flush_dcache_icache_page(page);
                        set_bit(PG_arch_1, &page->flags);
                }

Which worked to due to pure luck: PG_arch_1 was always unset before, but
now it isnt.

The root of the problem are the changes against the 8xx TLB handlers introduced
during v2.6. What happens is the TLBMiss handlers load the zeroed pte into
the TLB, causing the TLBError handler to be invoked (thats two TLB faults per 
pagefault), which then jumps to the generic MM code to setup the pte.

The bug is that the zeroed TLB is not invalidated (the same reason
for the "dcbst" misbehaviour), resulting in infinite TLBError faults.

The "two exception" approach requires a TLB flush (to nuke the zeroed TLB)
at each PTE update for correct behaviour:
Signed-off-by: NMarcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Our performance validation on 2.6.15-rc1 caught a disastrous performance
regression on ia64 with netperf (-98%) and volanomark (-58%) compares to
previous kernel version 2.6.14-git7.  See the following chart (result
group 1 & 2).

  http://kernel-perf.sourceforge.net/results.machine_id=26.html

We have root caused it to commit 64c7c8f8

This changeset broke the ia64 task resched notification.  In
sched.c:resched_task(), a reschedule IPI is conditioned upon
TIF_POLLING_NRFLAG.  However, the above changeset unconditionally set
the polling thread flag for idle tasks regardless whether pal_halt_light
is in use or not.  As a result, resched IPI is not sent from
resched_task().  And since the default behavior on ia64 is to use
pal_halt_light, we end up delaying the rescheduling task until next
timer tick, and thus cause the performance regression.

This fixes the performance bug.  I'm glad our performance suite is
turning up bad performance bug like this in time.
Signed-off-by: NKen Chen <kenneth.w.chen@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This avoids a BUG_ON with kref.c when SA1111 tries to register
a driver with an unregistered bus type.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

- Fix a regression in command completion, which prevented
  the restart of the DMA engine after the device throws
  an error.
- Pack more hardware info into the port-reset error message.
- Promote "welcome to our timeout" message from debug msg
  to normal printk.

Something I've found handy countless times when users do this..
Signed-off-by: NDave Jones <davej@redhat.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Picked from the ubuntu-2.6 tree

The change in location for ll_rw_blk.c from drivers/block/ to block/ caused
failure to generate documentation.
Signed-off-by: NBen Collins <bcollins@ubuntu.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

drivers/block/cciss_scsi.c:264: warning: `print_bytes' defined but not used
drivers/block/cciss_scsi.c:298: warning: `print_cmd' defined but not used
Signed-off-by: NGrant Coady <gcoady@gmail.com>
Acked-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NMiles Bader <miles@gnu.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NMiles Bader <miles@gnu.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A variable was being used in multiple conflicting ways.  I also restructured
the code a bit for clarity.
Signed-off-by: NMiles Bader <miles@gnu.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

gcc4 doesn't allow typecasted lvals.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We need to use the USB_DEVICE macro here, else the modinfo aliases go all wrong.

Also, correctly terminate the table, as noted by Dave Jones <davej@redhat.com>

Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Acked-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Despite the fact that md threads don't need to be signalled, and won't
respond to signals anyway, we need to have an 'interruptible' wait, else
they stay in 'D' state and add to the load average.

(akpm: the signal_pending() test is unneeded - we'll fix that up in the next
round.  For now, leave it there because that's how the code used to be).
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This was marked deprecated "after 2.6" back in the 2.5 days.  But now it
seems there isn't going to be any "after 2.6", and we deprecate by date
now.  So set a date.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Being kernel-threads, nfsd servers don't get pre-empted (depending on
CONFIG).  If there is a steady stream of NFS requests that can be served
from cache, an nfsd thread may hold on to a cpu indefinitely, which isn't
very friendly.

So it is good to have a cond_resched in there (just before looking for a
new request to serve), to make sure we play nice.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

These exported symbols are in arch/ppc/ but missing from arch/powerpc/ for
ppc32 builds.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Lots of good changes to the driver lately that userspace will care about
the version of the driver.  Bump the version from 36.0 to 38.0 to be higher
than 37 that the 2.4 driver came out with a few weeks ago which doesn't
have all the same changes.
Signed-off-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make sysctl.h (again) useable from userspace
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A patch by Eric was merged (f2b36db6)
and later on reverted back (1e4c85f9).

Along with above patch, another patch was posted and has been merged
(3d1675b4).  That patch was dependent on
the above patch and now it should also be reverted.

Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rather than defining our own PM option, use kernel/power/Kconfig.
This fixes build errors introduced by
bca73e4bSigned-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix up booting with sparse mem enabled. Otherwise it would just
cause an early PANIC at boot.
Signed-off-by: NBob Picco <bob.picco@hp.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is needed for large multinode IBM systems which have a sparse
APIC space in clustered mode, fully covering the available 8 bits.

The previous kernels would limit the local APIC number to 127,
which caused it to reject some of the CPUs at boot.

I increased the maximum and shrunk the apic_version array a bit
to make up for that (the version is only 8 bit, so don't need
an full int to store)

Cc:  Chris McDermott <lcm@us.ibm.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

CONFIG_CHECKING covered some debugging code used in the early times
of the port. But it wasn't even SMP safe for quite some time
and the bugs it checked for seem to be gone.

This patch removes all the code to verify GS at kernel entry. There
haven't been any new bugs in this area for a long time.

Previously it also covered the sysctl for the page fault tracing.
That didn't make much sense because that code was unconditionally
compiled in. I made that a boot option now because it is typically
only useful at boot.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The current x86_64 NUMA memory code is inconsequent when it comes to node
memory ranges. The exact behaviour varies depending on which config option
that is used.

setup_node_bootmem() has start and end as arguments and these are used to
calculate the size of the node like this: (end - start). This is all fine
if end is pointing to the first non-available byte. The problem is that the
current x86_64 code sometimes treats it as the last present byte and sometimes
as the first non-available byte. The result is that some configurations might
lose a page at the end of the range.

This patch tries to fix CONFIG_ACPI_NUMA, CONFIG_K8_NUMA and CONFIG_NUMA_EMU
so they all treat the end variable as the first non-available byte. This is
the same way as the single node code.

The patch is boot tested on dual x86_64 hardware with the above configurations,
but maybe the removed code is needed as some workaround?
Signed-off-by: NMagnus Damm <magnus@valinux.co.jp>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The logging for boot errors was turned off because it was broken
on some AMD systems. But give Intel EM64T systems a chance because they are
supposed to be correct there.

The advantage is that there is a chance to actually log uncorrected
machine checks after the reset.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

On x86_64 arches, there is no way to choose ACPI_NUMA without having to choose
K8_NUMA.  CONFIG_K8_NUMA is not needed for Intel EM64T NUMA boxes.  It also
looks odd if you have to select ACPI_NUMA from the power management menu.
This patch fixes those oddities.  Patch does the following:

1. Makes NUMA a config option like other arches
2. Makes topology detection options like K8_NUMA dependent on NUMA
3. Choosing ACPI NUMA detection can be done from the standard
   "Processor type and features" menu

AK: I fixed up the dependencies and changed the help texts a bit
on top of Kiran's patch.
Signed-off-by: NRavikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: NShai Fultheim <shai@scalex86.org>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Keeping this function does not makes sense because it's a copied (and
buggy) copy of sys_time.  The only difference is that now.tv_sec (which is
a time_t, i.e.  a 64-bit long) is copied (and truncated) into a int
(32-bit).

The prototype is the same (they both take a long __user *), so let's drop
this and redirect it to sys_time (and make sure it exists by defining
__ARCH_WANT_SYS_TIME).

Only disadvantage is that the sys_stime definition is also compiled (may be
fixed if needed by adding a separate __ARCH_WANT_SYS_STIME macro, and
defining it for all arch's defining __ARCH_WANT_SYS_TIME except x86_64).
Acked-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The current value was correct before the introduction of Intel EM64T support -
but now L1_CACHE_SHIFT_MAX can be less than L1_CACHE_SHIFT, which _is_ funny!

Between the few users of ____cacheline_maxaligned_in_smp, we also have (for
example) rcu_ctrlblk, and struct zone, with zone->{lru_,}lock.  I.e.  we have
a lot of excess cacheline bouncing on them.

No correctness issues, obviously.  So this could even be merged for 2.6.14
(I'm not a fan of this idea, though).

CC: Andi Kleen <ak@suse.de>
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Not needed since x86-64 always uses the spinlock based rwsems.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

B stepping were the first shipping Opterons. memcpy/memset/copy_page/
clear_page had special optimized version for them. These are really
old and in the minority now and the difference to the generic versions
(using rep microcode) is not that big anyways. So just remove them.

TODO: figure out optimized versions for Intel Netburst based EM64T
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Old code could retry for 10 seconds worst time. Only try it
for one second now.

Suggested by Yinghai Lu

Cc: Yinghai.Lu@amd.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix the Intel cache detection code assumption that number of threads
sharing the cache will either be equal to number of HT or core siblings.

This also cleans up the code in general a bit.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fields obtained through cpuid vector 0x1(ebx[16:23]) and
vector 0x4(eax[14:25], eax[26:31]) indicate the maximum values and might not
always be the same as what is available and what OS sees.  So make sure
"siblings" and "cpu cores" values in /proc/cpuinfo reflect the values as seen
by OS instead of what cpuid instruction says. This will also fix the buggy BIOS
cases (for example where cpuid on a single core cpu says there are "2" siblings,
even when HT is disabled in the BIOS.
http://bugzilla.kernel.org/show_bug.cgi?id=4359)
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When they were disabled before (e.g. after a panic) it's better
to keep them off, otherwise followon panics can happen from timer
interrupt handlers etc.

Drawback is that pageup in the console won't work anymore though.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

No functional changes.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>