Dave Chinner reported that commit 4d942466 ("mm: convert
p[te|md]_mknonnuma and remaining page table manipulations") slowed down
his xfsrepair test enormously.  In particular, it was using more system
time due to extra TLB flushing.

The ultimate reason turns out to be how the change to use the regular
page table accessor functions broke the NUMA grouping logic.  The old
special mknuma/mknonnuma code accessed the page table present bit and
the magic NUMA bit directly, while the new code just changes the page
protections using PROT_NONE and the regular vma protections.

That sounds equivalent, and from a fault standpoint it really is, but a
subtle side effect is that the *other* protection bits of the page table
entries also change.  And the code to decide how to group the NUMA
entries together used the writable bit to decide whether a particular
page was likely to be shared read-only or not.

And with the change to make the NUMA handling use the regular permission
setting functions, that writable bit was basically always cleared for
private mappings due to COW.  So even if the page actually ends up being
written to in the end, the NUMA balancing would act as if it was always
shared RO.

This code is a heuristic anyway, so the fix - at least for now - is to
instead check whether the page is dirty rather than writable.  The bit
doesn't change with protection changes.

NOTE! This also adds a FIXME comment to revisit this issue,

Not only should we probably re-visit the whole "is this a shared
read-only page" heuristic (we might want to take the vma permissions
into account and base this more on those than the per-page ones, and
also look at whether the particular access that triggers it is a write
or not), but the whole COW issue shows that we should think about the
NUMA fault handling some more.

For example, maybe we should do the early-COW thing that a regular fault
does.  Or maybe we should accept that while using the same bits as
PROTNONE was a good thing (and got rid of the specual NUMA bit), we
might still want to just preseve the other protection bits across NUMA
faulting.

Those are bigger questions, left for later.  This just fixes up the
heuristic so that it at least approximates working again.  More analysis
and work needed.
Reported-by: NDave Chinner <david@fromorbit.com>
Tested-by: NMel Gorman <mgorman@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>,
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull MTD fixes from Brian Norris:

 * pxa3xx_nand
   - fix timeout issues when draining the FIFO (BCH only)
   - don't crash when no chip-selects are used

 * hisi504_nand
   - depend on HAS_DMA, to fix compile errors

* tag 'for-linus-20150310' of git://git.infradead.org/linux-mtd:
  mtd: nand: MTD_NAND_HISI504 should depend on HAS_DMA
  mtd: pxa3xx_nand: fix driver when num_cs is 0
  mtd: nand: pxa3xx: Fix PIO FIFO draining

Pull iommu fixes from Joerg Roedel:
 "The patches contain:

   - fix multiple ARM IOMMU drivers to behave well when the hardware is
     not present

   - mark MSM driver as broken

   - fix build errors with the new ARM generic io-page-table code"

* tag 'iommu-fixes-v4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/io-pgtable-arm: Add built time dependency
  iommu/msm: Mark driver BROKEN
  iommu/rockchip: Play nice in multi-platform builds
  iommu/omap: Play nice in multi-platform builds
  iommu/exynos: Play nice in multi-platform builds
  iommu/io-pgtable-arm: Fix self-test WARNs on i386

Pull kvm/s390 bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: s390: non-LPAR case obsolete during facilities mask init
  KVM: s390: include guest facilities in kvm facility test
  KVM: s390: fix in memory copy of facility lists
  KVM: s390/cpacf: Fix kernel bug under z/VM
  KVM: s390/cpacf: Enable key wrapping by default

Pull s390 fixes from Martin Schwidefsky:
 "One performance optimization for page_clear and a couple of bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/mm: fix incorrect ASCE after crst_table_downgrade
  s390/ftrace: fix crashes when switching tracers / add notrace to cpu_relax()
  s390/pci: unify pci_iomap symbol exports
  s390/pci: fix [un]map_resources sequence
  s390: let the compiler do page clearing
  s390/pci: fix possible information leak in mmio syscall
  s390/dcss: array index 'i' is used before limits check.
  s390/scm_block: fix off by one during cluster reservation
  s390/jump label: improve and fix sanity check
  s390/jump label: add missing jump_label_apply_nops() call

Merge tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull seq-buf/ftrace fixes from Steven Rostedt:
 "This includes fixes for seq_buf_bprintf() truncation issue.  It also
  contains fixes to ftrace when /proc/sys/kernel/ftrace_enabled and
  function tracing are started.  Doing the following causes some issues:

    # echo 0 > /proc/sys/kernel/ftrace_enabled
    # echo function_graph > /sys/kernel/debug/tracing/current_tracer
    # echo 1 > /proc/sys/kernel/ftrace_enabled
    # echo nop > /sys/kernel/debug/tracing/current_tracer
    # echo function_graph > /sys/kernel/debug/tracing/current_tracer

  As well as with function tracing too.  Pratyush Anand first reported
  this issue to me and supplied a patch.  When I tested this on my x86
  test box, it caused thousands of backtraces and warnings to appear in
  dmesg, which also caused a denial of service (a warning for every
  function that was listed).  I applied Pratyush's patch but it did not
  fix the issue for me.  I looked into it and found a slight problem
  with trampoline accounting.  I fixed it and sent Pratyush a patch, but
  he said that it did not fix the issue for him.

  I later learned tha Pratyush was using an ARM64 server, and when I
  tested on my ARM board, I was able to reproduce the same issue as
  Pratyush.  After applying his patch, it fixed the problem.  The above
  test uncovered two different bugs, one in x86 and one in ARM and
  ARM64.  As this looked like it would affect PowerPC, I tested it on my
  PPC64 box.  It too broke, but neither the patch that fixed ARM or x86
  fixed this box (the changes were all in generic code!).  The above
  test, uncovered two more bugs that affected PowerPC.  Again, the
  changes were only done to generic code.  It's the way the arch code
  expected things to be done that was different between the archs.  Some
  where more sensitive than others.

  The rest of this series fixes the PPC bugs as well"

* tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix ftrace enable ordering of sysctl ftrace_enabled
  ftrace: Fix en(dis)able graph caller when en(dis)abling record via sysctl
  ftrace: Clear REGS_EN and TRAMP_EN flags on disabling record via sysctl
  seq_buf: Fix seq_buf_bprintf() truncation
  seq_buf: Fix seq_buf_vprintf() truncation

Pull networking fixes from David Miller:

 1) nft_compat accidently truncates ethernet protocol to 8-bits, from
    Arturo Borrero.

 2) Memory leak in ip_vs_proc_conn(), from Julian Anastasov.

 3) Don't allow the space required for nftables rules to exceed the
    maximum value representable in the dlen field.  From Patrick
    McHardy.

 4) bcm63xx_enet can accidently leave interrupts permanently disabled
    due to errors in the NAPI polling exit logic.  Fix from Nicolas
    Schichan.

 5) Fix OOPSes triggerable by the ping protocol module, due to missing
    address family validations etc.  From Lorenzo Colitti.

 6) Don't use RCU locking in sleepable context in team driver, from Jiri
    Pirko.

 7) xen-netback miscalculates statistic offset pointers when reporting
    the stats to userspace.  From David Vrabel.

 8) Fix a leak of up to 256 pages per VIF destroy in xen-netaback, also
    from David Vrabel.

 9) ip_check_defrag() cannot assume that skb_network_offset(),
    particularly when it is used by the AF_PACKET fanout defrag code.
    From Alexander Drozdov.

10) gianfar driver doesn't query OF node names properly when trying to
    determine the number of hw queues available.  Fix it to explicitly
    check for OF nodes named queue-group.  From Tobias Waldekranz.

11) MID field in macb driver should be 12 bits, not 16.  From Punnaiah
    Choudary Kalluri.

12) Fix unintentional regression in traceroute due to timestamp socket
    option changes.  Empty ICMP payloads should be allowed in
    non-timestamp cases.  From Willem de Bruijn.

13) When devices are unregistered, we have to get rid of AF_PACKET
    multicast list entries that point to it via ifindex.  Fix from
    Francesco Ruggeri.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
  tipc: fix bug in link failover handling
  net: delete stale packet_mclist entries
  net: macb: constify macb configuration data
  MAINTAINERS: add Marc Kleine-Budde as co maintainer for CAN networking layer
  MAINTAINERS: linux-can moved to github
  can: kvaser_usb: Read all messages in a bulk-in URB buffer
  can: kvaser_usb: Avoid double free on URB submission failures
  can: peak_usb: fix missing ctrlmode_ init for every dev
  can: add missing initialisations in CAN related skbuffs
  ip: fix error queue empty skb handling
  bgmac: Clean warning messages
  tcp: align tcp_xmit_size_goal() on tcp_tso_autosize()
  net: fec: fix unbalanced clk disable on driver unbind
  net: macb: Correct the MID field length value
  net: gianfar: correctly determine the number of queue groups
  ipv4: ip_check_defrag should not assume that skb_network_offset is zero
  net: bcmgenet: properly disable password matching
  net: eth: xgene: fix booting with devicetree
  bnx2x: Force fundamental reset for EEH recovery
  xen-netback: refactor xenvif_handle_frag_list()
  ...

Pull input subsystem fixes from Dmitry Torokhov:
 "Miscellaneous driver fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: psmouse - disable "palm detection" in the focaltech driver
  Input: psmouse - disable changing resolution/rate/scale for FocalTech
  Input: psmouse - ensure that focaltech reports consistent coordinates
  Input: psmouse - remove hardcoded touchpad size from the focaltech driver
  Input: tc3589x-keypad - set IRQF_ONESHOT flag to ensure IRQ request
  Input: ALPS - fix memory leak when detection fails
  Input: sun4i-ts - add thermal driver dependency
  Input: cyapa - remove superfluous type check in cyapa_gen5_read_idac_data()
  Input: cyapa - fix unaligned functions redefinition error
  Input: mma8450 - add parent device

Pull regulator fixes from Mark Brown:
 "A couple of driver specific fixes plus a fix for a regression in the
  core where the updates to use sysfs group registration were overly
  enthusiastic in eliding properties and removed some that had been
  previously present"

* tag 'regulator-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: Fix regression due to NULL constraints check
  regulator: rk808: Set the enable time for LDOs
  regulator: da9210: Mask all interrupt sources to deassert interrupt line

Pull spi fixes from Mark Brown:
 "A collection of driver specific fixes to which the usual comments
  about them being important if you see them mostly apply (except for
  the comment fix).  The pl022 one is particularly nasty for anyone
  affected by it"

* tag 'spi-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: pl022: Fix race in giveback() leading to driver lock-up
  spi: dw-mid: avoid potential NULL dereference
  spi: img-spfi: Verify max spfi transfer length
  spi: fix a typo in comment.
  spi: atmel: Fix interrupt setup for PDC transfers
  spi: dw: revisit FIFO size detection again
  spi: dw-pci: correct number of chip selects
  drivers: spi: ti-qspi: wait for busy bit clear before data write/read

Pull tpm fixes from James Morris:
 "fixes for the TPM driver"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  tpm: fix call order in tpm-chip.c
  tpm/ibmvtpm: Additional LE support for tpm_ibmvtpm_send

Pull fbdev fixes from Tomi Valkeinen:
 - Fix regression in with omapdss when using i2c displays
 - Fix possible null deref in fbmon
 - Check kalloc return value in AMBA CLCD

* tag 'fbdev-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  OMAPDSS: fix regression with display sysfs files
  video: fbdev: fix possible null dereference
  video: ARM CLCD: Add missing error check for devm_kzalloc

Pull cgroup fixes from Tejun Heo:
 "The cgroup iteration update two years ago and the recent cpuset
  restructuring introduced regressions in subset of cpuset
  configurations.  Three patches to fix them.

  All are marked for -stable"

* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset: Fix cpuset sched_relax_domain_level
  cpuset: fix a warning when clearing configured masks in old hierarchy
  cpuset: initialize effective masks when clone_children is enabled

Pull libata fixlet from Tejun Heo:
 "Speed limiting fix for sata_fsl"

* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  sata-fsl: Apply link speed limits

Pull workqueue fix from Tejun Heo:
 "One fix patch for a subtle livelock condition which can happen on
  PREEMPT_NONE kernels involving two racing cancel_work calls.  Whoever
  comes in the second has to wait for the previous one to finish.  This
  was implemented by making the later one block for the same condition
  that the former would be (work item completion) and then loop and
  retest; unfortunately, depending on the wake up order, the later one
  could lock out the former one to finish by busy looping on the cpu.

  This is fixed by implementing explicit wait mechanism.  Work item
  might not belong anywhere at this point and there's remote possibility
  of thundering herd problem.  I originally tried to use bit_waitqueue
  but it didn't work for static work items on modules.  It's currently
  using single wait queue with filtering wake up function and exclusive
  wakeup.  If this ever becomes a problem, which is not very likely, we
  can try to figure out a way to piggy back on bit_waitqueue"

* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: fix hang involving racing cancel[_delayed]_work_sync()'s for PREEMPT_NONE

In commit c637c103
("tipc: resolve race problem at unicast message reception") we
introduced a new mechanism for delivering buffers upwards from link
to socket layer.

That code contains a bug in how we handle the new link input queue
during failover. When a link is reset, some of its users may be blocked
because of congestion, and in order to resolve this, we add any pending
wakeup pseudo messages to the link's input queue, and deliver them to
the socket. This misses the case where the other, remaining link also
may have congested users. Currently, the owner node's reference to the
remaining link's input queue is unconditionally overwritten by the
reset link's input queue. This has the effect that wakeup events from
the remaining link may be unduely delayed (but not lost) for a
potentially long period.

We fix this by adding the pending events from the reset link to the
input queue that is currently referenced by the node, whichever one
it is.

This commit should be applied to both net and net-next.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an interface is deleted from a net namespace the ifindex in the
corresponding entries in PF_PACKET sockets' mclists becomes stale.
This can create inconsistencies if later an interface with the same ifindex
is moved from a different namespace (not that unlikely since ifindexes are
per-namespace).
In particular we saw problems with dev->promiscuity, resulting
in "promiscuity touches roof, set promiscuity failed. promiscuity
feature of device might be broken" warnings and EOVERFLOW failures of
setsockopt(PACKET_ADD_MEMBERSHIP).
This patch deletes the mclist entries for interfaces that are deleted.
Since this now causes setsockopt(PACKET_DROP_MEMBERSHIP) to fail with
EADDRNOTAVAIL if called after the interface is deleted, also make
packet_mc_drop not fail.
Signed-off-by: NFrancesco Ruggeri <fruggeri@arista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The configurations are not modified by the driver.  Make them 'const' so
that they may be placed in a read-only section.
Signed-off-by: NJosh Cartwright <joshc@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.0-20150309' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2015-03-09

this is a pull request for net/master for the 4.0 release cycle, it consists of
6 patches:

A patch by Oliver Hartkopp fixes a long outstanding bug in the infrastructure,
which leads to skb_under_panics when CAN interfaces are used by AF_PACKET
sockets e.g. by dhclient. Stephane Grosjean contributes a patch for the
peak_usb driver which adds a missing initialization. Two patches by Ahmed S.
Darwish fix problems in the kvaser_usb driver. Followed by two patches by
myself, updating the MAINTAINERS file
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some archs (specifically PowerPC), are sensitive with the ordering of
the enabling of the calls to function tracing and setting of the
function to use to be traced.

That is, update_ftrace_function() sets what function the ftrace_caller
trampoline should call. Some archs require this to be set before
calling ftrace_run_update_code().

Another bug was discovered, that ftrace_startup_sysctl() called
ftrace_run_update_code() directly. If the function the ftrace_caller
trampoline changes, then it will not be updated. Instead a call
to ftrace_startup_enable() should be called because it tests to see
if the callback changed since the code was disabled, and will
tell the arch to update appropriately. Most archs do not need this
notification, but PowerPC does.

The problem could be seen by the following commands:

 # echo 0 > /proc/sys/kernel/ftrace_enabled
 # echo function > /sys/kernel/debug/tracing/current_tracer
 # echo 1 > /proc/sys/kernel/ftrace_enabled
 # cat /sys/kernel/debug/tracing/trace

The trace will show that function tracing was not active.

Cc: stable@vger.kernel.org # 2.6.27+
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When ftrace is enabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when
ftrace is disabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_STOP_FUNC_RET command to ftrace_run_update_code().

Consider the following situation.

 # echo 0 > /proc/sys/kernel/ftrace_enabled

After this ftrace_enabled = 0.

 # echo function_graph > /sys/kernel/debug/tracing/current_tracer

Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never
called.

 # echo 1 > /proc/sys/kernel/ftrace_enabled

Now ftrace_enabled will be set to true, but still
ftrace_enable_ftrace_graph_caller() will not be called, which is not
desired.

Further if we execute the following after this:
  # echo nop > /sys/kernel/debug/tracing/current_tracer

Now since ftrace_enabled is set it will call
ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on
the ARM platform.

On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called,
it checks whether the old instruction is a nop or not. If it's not a nop,
then it returns an error. If it is a nop then it replaces instruction at
that address with a branch to ftrace_graph_caller.
ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore,
if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller()
or ftrace_disable_ftrace_graph_caller() consecutively two times in a row,
then it will return an error, which will cause the generic ftrace code to
raise a warning.

Note, x86 does not have an issue with this because the architecture
specific code for ftrace_enable_ftrace_graph_caller() and
ftrace_disable_ftrace_graph_caller() does not check the previous state,
and calling either of these functions twice in a row has no ill effect.

Link: http://lkml.kernel.org/r/e4fbe64cdac0dd0e86a3bf914b0f83c0b419f146.1425666454.git.panand@redhat.com

Cc: stable@vger.kernel.org # 2.6.31+
Signed-off-by: NPratyush Anand <panand@redhat.com>
[
  removed extra if (ftrace_start_up) and defined ftrace_graph_active as 0
  if CONFIG_FUNCTION_GRAPH_TRACER is not set.
]
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When /proc/sys/kernel/ftrace_enabled is set to zero, all function
tracing is disabled. But the records that represent the functions
still hold information about the ftrace_ops that are hooked to them.

ftrace_ops may request "REGS" (have a full set of pt_regs passed to
the callback), or "TRAMP" (the ops has its own trampoline to use).
When the record is updated to represent the state of the ops hooked
to it, it sets "REGS_EN" and/or "TRAMP_EN" to state that the callback
points to the correct trampoline (REGS has its own trampoline).

When ftrace_enabled is set to zero, all ftrace locations are a nop,
so they do not point to any trampoline. But the _EN flags are still
set. This can cause the accounting to go wrong when ftrace_enabled
is cleared and an ops that has a trampoline is registered or unregistered.

For example, the following will cause ftrace to crash:

 # echo function_graph > /sys/kernel/debug/tracing/current_tracer
 # echo 0 > /proc/sys/kernel/ftrace_enabled
 # echo nop > /sys/kernel/debug/tracing/current_tracer
 # echo 1 > /proc/sys/kernel/ftrace_enabled
 # echo function_graph > /sys/kernel/debug/tracing/current_tracer

As function_graph uses a trampoline, when ftrace_enabled is set to zero
the updates to the record are not done. When enabling function_graph
again, the record will still have the TRAMP_EN flag set, and it will
look for an op that has a trampoline other than the function_graph
ops, and fail to find one.

Cc: stable@vger.kernel.org # 3.17+
Reported-by: NPratyush Anand <panand@redhat.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

This patch adds Marc Kleine-Budde as a co maintainer for the CAN networking
layer.
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

As gitorious will shut down at the end of May 2015, the linux-can website moved
to github. This patch reflects this change.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.

The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.

Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: NAhmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself.  Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.

Remove two of such invalid manual free().
Signed-off-by: NAhmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Fixes a missing initialization of ctrlmode and ctrlmode_supported fields,
for all other CAN devices than the first one. This fix only concerns
the PCAN-USB Pro FD dual-channels CAN-FD device made by PEAK-System.
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.

Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: NAustin Schuh <austin@peloton-tech.com>
Reported-by: NDaniel Steer <daniel.steer@mclaren.com>
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

When reading from the error queue, msg_name and msg_control are only
populated for some errors. A new exception for empty timestamp skbs
added a false positive on icmp errors without payload.

`traceroute -M udpconn` only displayed gateways that return payload
with the icmp error: the embedded network headers are pulled before
sock_queue_err_skb, leaving an skb with skb->len == 0 otherwise.

Fix this regression by refining when msg_name and msg_control
branches are taken. The solutions for the two fields are independent.

msg_name only makes sense for errors that configure serr->port and
serr->addr_offset. Test the first instead of skb->len. This also fixes
another issue. saddr could hold the wrong data, as serr->addr_offset
is not initialized  in some code paths, pointing to the start of the
network header. It is only valid when serr->port is set (non-zero).

msg_control support differs between IPv4 and IPv6. IPv4 only honors
requests for ICMP and timestamps with SOF_TIMESTAMPING_OPT_CMSG. The
skb->len test can simply be removed, because skb->dev is also tested
and never true for empty skbs. IPv6 honors requests for all errors
aside from local errors and timestamps on empty skbs.

In both cases, make the policy more explicit by moving this logic to
a new function that decides whether to process msg_control and that
optionally prepares the necessary fields in skb->cb[]. After this
change, the IPv4 and IPv6 paths are more similar.

The last case is rxrpc. Here, simply refine to only match timestamps.

Fixes: 49ca0d8b ("net-timestamp: no-payload option")
Reported-by: NJan Niehusmann <jan@gondor.com>
Signed-off-by: NWillem de Bruijn <willemb@google.com>

----

Changes
  v1->v2
  - fix local origin test inversion in ip6_datagram_support_cmsg
  - make v4 and v6 code paths more similar by introducing analogous
    ipv4_datagram_support_cmsg
  - fix compile bug in rxrpc
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

POLL_OUT isn't what callers of ->poll() are expecting to see; it's
actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap
bit...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Cc: Bruce Fields <bfields@fieldses.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull USB fixes from Greg KH:
 "Here's a round of USB fixes for 4.0-rc3.

  Nothing major, the usual gadget, xhci and usb-serial fixes and a few
  new device ids as well.

  All have been in linux-next successfully"

* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
  xhci: Workaround for PME stuck issues in Intel xhci
  xhci: fix reporting of 0-sized URBs in control endpoint
  usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
  USB: ch341: set tty baud speed according to tty struct
  USB: serial: cp210x: Adding Seletek device id's
  USB: pl2303: disable break on shutdown
  USB: mxuport: fix null deref when used as a console
  USB: serial: clean up bus probe error handling
  USB: serial: fix port attribute-creation race
  USB: serial: fix tty-device error handling at probe
  USB: serial: fix potential use-after-free after failed probe
  USB: console: add dummy __module_get
  USB: ftdi_sio: add PIDs for Actisense USB devices
  Revert "USB: serial: make bulk_out_size a lower limit"
  cdc-acm: Add support for Denso cradle CU-321
  usb-storage: support for more than 8 LUNs
  uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
  USB: usbfs: don't leak kernel data in siginfo
  xhci: Clear the host side toggle manually when endpoint is 'soft reset'
  xhci: Allocate correct amount of scratchpad buffers
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some tty and serial driver fixes for 4.0-rc3.

  Along with the atime fix that you know about, here are some other
  serial driver bugfixes as well.  Most notable is a wait_until_sent
  bugfix that was traced back to being around since before 2.6.12 that
  Johan has fixed up.

  All have been in linux-next successfully"

* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  TTY: fix tty_wait_until_sent maximum timeout
  TTY: fix tty_wait_until_sent on 64-bit machines
  USB: serial: fix infinite wait_until_sent timeout
  TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
  net: irda: fix wait_until_sent poll timeout
  serial: uapi: Declare all userspace-visible io types
  serial: core: Fix iotype userspace breakage
  serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
  console: Fix console name size mismatch
  tty: fix up atime/mtime mess, take four
  serial: 8250_dw: Fix get_mctrl behaviour
  serial:8250:8250_pci: delete unneeded quirk entries
  serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
  Change email address for 8250_pci
  serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
  Revert "tty/serial: of_serial: add DT alias ID handling"

Pull staging driver fixes from Greg KH:
 "Here are some IIO and staging driver fixes for 4.0-rc3.

  Details are in the shortlog, nothing major, mostly IIO fixes for
  reported issues.

  All have been in linux-next successfully"

* tag 'staging-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
  staging: comedi: adv_pci1710: fix AI INSN_READ for non-zero channel
  staging: comedi: vmk80xx: remove "firmware version" kernel messages
  staging: comedi: comedi_isadma: fix "stalled" detect in comedi_isadma_disable_on_sample()
  iio: ak8975: fix AK09911 dependencies
  iio: common: ssp_sensors: Protect PM-only functions to kill warning
  IIO: si7020: Allocate correct amount of memory in devm_iio_device_alloc
  Revert "iio:humidity:si7020: fix pointer to i2c client"
  iio: light: gp2ap020a00f: Select REGMAP_I2C
  iio: light: jsa1212: Select REGMAP_I2C
  iio: ad5686: fix optional reference voltage declaration
  iio:adc:mcp3422 Fix incorrect scales table
  iio: mxs-lradc: fix iio channel map regression
  iio: imu: adis16400: Fix sign extension
  staging: iio: ad2s1200: Fix sign extension
  iio: mxs-lradc: only update the buffer when its conversions have finished
  iio: mxs-lradc: make ADC reads not unschedule touchscreen conversions
  iio: mxs-lradc: make ADC reads not disable touchscreen interrupts
  iio: mxs-lradc: separate touchscreen and buffer virtual channels
  iio: imu: inv_mpu6050: Prevent dereferencing NULL
  iio: iadc: wait_for_completion_timeout time in jiffies
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are two char/misc fixes for 4.0-rc3.

  One is a reported binder driver fix needed due to a change in the mm
  core that happened in 4.0-rc1.  Another is a mei driver fix that
  resolves a reported issue in that driver.

  Both have been in linux-next for a while"

* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: make device disabled on stop unconditionally
  android: binder: fix binder mmap failures

Pull "code of conflict" from Greg KH:
 "This file tries to set the rational basis for our code reviews, gives
  some advice on how to conduct them, and provides an excalation channel
  for any kernel developers if they so desire it"

[ Let's see how this works ]

* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Code of Conflict

Apparently, the threshold for large contact area seems to be rather low on
some devices, causing the touchpad to frequently freeze during normal
usage. Because we do now know how we are supposed to use the value in
question, this commit just drops the related code completely.
Signed-off-by: NMathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

These PS/2 commands make some touchpads stop responding, so this commit
adds some dummy functions to replace the generic implementation. Because
scale changes were not encapsulated in a method of struct psmouse yet, this
commit adds a method set_scale to psmouse.
Signed-off-by: NMathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>