Enable gcov support for ARM based on original patches by David
Singleton and George G. Davis

Riku - updated to patch to current mainline kernel. The patch
has been submitted in 2010, 2012 - for symmetry, now in 2014 too.

https://lwn.net/Articles/390419/
http://marc.info/?l=linux-arm-kernel&m=133823081813044

v2: remove arch/arm/kernel from gcov disabled files

Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRiku Voipio <riku.voipio@linaro.org>
Signed-off-by: NVincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix incorrect clock names for usb1, pcie1 and domain register
offset for pcie1 clock nodes on K2E EVM
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

using LVDS channel 1 on an i.MX53 leads to following error:

imx-ldb 53fa8008.ldb: unable to set di0 parent clock to ldb_di1

This comes from imx_ldb_set_clock with mux = 0. Mux parameter must be "1" for
reparenting di1 clock to ldb_di1. The value of the mux param comes from device
tree port settings.

On i.MX5, the internal two-input-multiplexer is used. Due to hardware limitations,
only one port (port@[0,1]) can be used for each channel (lvds-channel@[0,1],
respectively)

Documentation update suggested by Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMarkus Niebel <Markus.Niebel@tq-group.com>
Fixes: e05c8c9a ("ARM: dts: imx53: Add IPU DI ports and endpoints, move imx-drm node to dtsi")
Cc: <stable@vger.kernel.org>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

LDO8 regulator is used for act led and serial cosole power supply.

Its DT status is declared as "disabled", however the serial console was
functional until Commit 318dbb02 ("regulator: palmas: Fix SMPS
enable/disable/is_enabled") wich properly turns off LDO8 on boot.

Fix serial cosole power supply (and act led) on boot by turning LDO8 on.

Fixes: 318dbb02 ("regulator: palmas: Fix SMPS enable/disable/is_enabled")
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Tested-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The nand timings were scaled down by 2 to account for
the 2x rate returned by clk_get_rate(gpmc_fclk).

As the clock data got fixed by [1], revert back to actual
timings (i.e. scale them up by 2).

Without this NAND doesn't work on dra7-evm.

[1] - commit dd94324b
    ARM: dts: dra7xx-clocks: Fix the l3 and l4 clock rates

Fixes: ff66a3c8 ("ARM: dts: dra7: add support for parallel NAND flash")
Cc: <stable@vger.kernel.org>        [3.16]
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The atmel,clk-divisors property is taking 4 divisors, if less are
provided, the clock registration will fail.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The at91sam9g20 SOC uses its own pllb implementation which is different
from the one inherited from at91sam9260 SOC.
Signed-off-by: NGaël PORTAY <gael.portay@gmail.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

DRA7 evm REV G and later boards uses a vtt regulator for DDR3
termination and this is controlled by gpio7_11. This gpio is
configured in boot loader. gpio7_11, which is only available only on
Pad A22, in previous boards, is connected only to an unused pad on
expansion connector EXP_P3 and is safe to be muxed as GPIO on all
DRA7-evm versions (without a need to spin off another dts file).

Since gpio7_11 is used to control VTT and should not be reset or kept
in idle state during boot up else VTT will be disconnected and DDR
gets corrupted. So, as part of this change, mark gpio7 as no-reset and
no-idle on init.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

While auditing the various pin ctrl configurations using the following
command:
grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line;
do
	v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 |
		cut -d 'x' -f2|tr [a-z] [A-Z]`;
	HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`;
	echo "$HEX ===> $line";
done)
against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014),
documentation errors were found for spi1 pinctrl. Fix the same.

Fixes: 6e58b8f1 ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.

Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.

CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NPekon Gupta <pekon@pek-sem.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.

Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NPekon Gupta <pekon@pek-sem.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.

This patch also gets rid of the below warning when NAND is
accessed for the first time.

omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NPekon Gupta <pekon@pek-sem.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.

For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NPekon Gupta <pekon@pek-sem.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.

For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NPekon Gupta <pekon@pek-sem.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Size should be 64KiB instead of 92KiB.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On the GP EVM, the ambient light sensor is limited to 100KHz on the
I2C bus.

So use 100kHz for I2C on the GP EVM due to this limitation on the
ambient light sensor.
Reported-by: NAparna Balasubramanian <aparnab@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.

CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.

Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.

CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The quite-recently-added analog-tv-connector bindings say that the
compatible string for composite video connector is
"composite-connector". That string is also used in the omap3-n900.dts
file. However, the connector driver uses "composite-video-connector", so
this has never worked.

While changing the driver's compatible string to "composite-connector"
would be safer, as published DT bindings should not be changed, I'd
rather fix the bindings in this case for two reasons:

* composite-connector is a bit too generic name, as it doesn't even hint
  at video.
* it's clear that this has never worked, which means no one has used
  those bindings, which should make it safe to change this.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Analogous to commit 8858d88a
that fixed commit 70b41abc
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.

For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

Commit 43fef47f (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.

This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678a (ARM: dts:
Revert enabling of twl configuration for n900).

Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.

This allows us to enable the PMIC configuration for n900.

Fixes: 43fef47f (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)

Cc: stable@vger.kernel.org # v3.16
Signed-off-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch is important for the MicroSOM implementation due to the
following details -

1. VIH of the Atheros phy is 1.7V.
2. NVCC_ENET which is the power domain of the MDIO pad is driven by the
   PHY's LDO (i.e. either 1.8v or 2.5v).
3. The MicroSOM implements an onbouard 1.6kohm pull up to 3.3v (R3000).

In the case the PHY's LDO was 1.8v then there would be only a 100mV
margin for the signal to be acknowledged as high (1.8v-1.7v).
Due to that setting the pad as an open drain will let the 1.6kohm pull
that signal high to 3.3 that assures enough margins to the PHY to be
acked as '1' logic.
Signed-off-by: NRabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Similarly to DRA7, OMAP5 has l3 and l4 clock rates incorrectly calculated.
Fixed by using proper divider clock types for the clock nodes.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Reported-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For device tree based booting, we need to use wake-up
interrupts like we already do for some omaps. This fixes
a PM regression on beagleboard compared to legacy booting.
Tested-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The kernel has never supported clk32g as a regulator since it is a clock
and not a regulator. Fortunately nothing actually references this node so
we can just remove it.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO modules are also interrupt sources. However, they require both the
GPIO number and IRQ type to function properly.

By declaring that GPIO uses interrupt-cells=<1>, we essentially do not
allow users of the nodes to use the interrupt property appropritely.

With this change, the following now works:

interrupt-parent = <&gpio6>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;

Fixes: 6e58b8f1 ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board')
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For v3.14 and prior, 1-bit Hamming code ECC via software was used
for NAND on this board.
Commit c06c5270 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.

This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So revert back to
using software ECC scheme.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Hummingboard has no over current hardware, so disable the over current
detection for both ports.

Cubox-i has over current hardware, so appropriately configure this.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:

pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table

Remove it to fix this.

Fixes: commit 1d41f36a ("ARM: shmobile:
       koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.

(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)

Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.

This of course renders them unusable, so readd the necessary pinctrl
properties.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Set 'ti,set-rate-parent' property for the dpll4_m5x2_ck clock, which
is used for the ISP functional clock. This fixes the OMAP3 ISP driver's
clock rate configuration on OMAP34xx, which needs the rate to be
propagated properly to the divider node (dpll4_m5_ck).
Signed-off-by: NStefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: <linux-media@vger.kernel.org>
Cc: <linux-omap@vger.kernel.org>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Increase max i2c bus frequency beyond the default for faster
data transfers. According to the manual, these faster speeds are
only available when the board is wired up the right way. In this case,
the vendor kernel has run at this speed for a long time.

sda-delay is needed for talking to RTC on PMIC, otherwise the i2c
controller never sees an ACK. Strangely the other PMIC i2c slave (the
main one) works fine even without this delay. I Chose value 100 to
match the vendor kernel.
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Tested-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The ODROID kernel shows that the PMIC interrupt line is hooked up
to pin GPX3-2.

This is needed for the max77686-irq driver to create the PMIC IRQ
domain, which is needed by max77686-rtc.
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Tested-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The following error is seen after a suspend/resume cycle on a mx53qsb with a
MC34708 PMIC:

root@freescale /$ echo mem > /sys/power/state
[   32.630592] PM: Syncing filesystems ... done.
[   32.643924] Freezing user space processes ... (elapsed 0.001 seconds) done.
[   32.652384] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[   32.679156] PM: suspend of devices complete after 13.113 msecs
[   32.685128] PM: suspend devices took 0.030 seconds
[   32.696109] PM: late suspend of devices complete after 6.133 msecs
[   33.313032] mc13xxx 0-0008: Failed to read IRQ status: -110
[   33.322009] PM: noirq suspend of devices complete after 619.667 msecs
[   33.328544] Disabling non-boot CPUs ...
[   33.335031] PM: noirq resume of devices complete after 2.352 msecs
[   33.842940] mc13xxx 0-0008: Failed to read IRQ status: -110
[   33.976095] [sched_delayed] sched: RT throttling activated
[   33.984804] PM: early resume of devices complete after 642.642 msecs
[   34.352954] mc13xxx 0-0008: Failed to read IRQ status: -110
[   34.862910] mc13xxx 0-0008: Failed to read IRQ status: -110
[   34.996595] PM: resume of devices complete after 1005.367 msecs
[   35.372925] mc13xxx 0-0008: Failed to read IRQ status: -110
[   35.882911] mc13xxx 0-0008: Failed to read IRQ status: -110
[   35.955707] PM: resume devices took 1.970 seconds
[   35.960445] Restarting tasks ... done.
[   35.993386] fec 63fec000.ethernet eth0: Link is Down
[   36.392980] mc13xxx 0-0008: Failed to read IRQ status: -110
[   36.902908] mc13xxx 0-0008: Failed to read IRQ status: -110
[   36.953036] ata1: SATA link down (SStatus 0 SControl 300)
[   37.412922] mc13xxx 0-0008: Failed to read IRQ status: -110
[   37.922906] mc13xxx 0-0008: Failed to read IRQ status: -110
[   37.993379] fec 63fec000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[   38.432938] mc13xxx 0-0008: Failed to read IRQ status: -110
[   38.942920] mc13xxx 0-0008: Failed to read IRQ status: -110
[   39.452933] mc13xxx 0-0008: Failed to read IRQ status: -110

(flood of this error message continues forever)

Commit 5169df8b ("ARM: dts: i.MX53: add support for MCIMX53-START-R")
missed to configure the IOMUX for the PMIC IRQ pin.

Configure the PMIC IRQ pin so that the suspend/resume sequence behaves cleanly
as expected.

Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The current pinfunc define all uart CTS_B IO port for DCE uart 'CTS_B'
IP port. Since uart IP port 'CTS_B' is output, and it don't need to
set 'SELECT_INPUT' bit.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The VPU on i.MX53 has two distinct clocks for register access and
internal function.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Fixes: fbf970f6 ("ARM: dts: mx53qsb: Enable VPU support")
Cc: <stable@vger.kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NSilvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Previous version had an extra 'fsl' which made the pins not match
any entry.  The console message,

 vf610-pinctrl 40048000.iomuxc: no fsl,pins property in node \
    /soc/aips-bus@40000000/iomuxc@40048000/vf610-twr/esdhc1grp

is displayed without the fix.  The prior version would generally
work as u-boot sets the pins properly for sdhc.  This change allows
Linux sdhc use even if u-boot is built without sdhc support.
Signed-off-by: NBill Pringlemeir <bpringlemeir@nbsps.com>
Acked-by: NStefan Agner <stefan@agner.ch>
Fixes: 0517fe6a ("ARM: dts: vf610-twr: Add support for sdhc1")
Cc: <stable@vger.kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>