Hardware always provides compliment of IP pseudo checksum. Stack expects
whole packet checksum without pseudo checksum if CHECKSUM_COMPLETE is set.

This causes checksum error in nf & ovs.

kernel: qg-19546f09-f2: hw csum failure
kernel: CPU: 9 PID: 0 Comm: swapper/9 Tainted: GF          O--------------   3.10.0-123.8.1.el7.x86_64 #1
kernel: Hardware name: Cisco Systems Inc UCSB-B200-M3/UCSB-B200-M3, BIOS B200M3.2.2.3.0.080820141339 08/08/2014
kernel: ffff881218f40000 df68243feb35e3a8 ffff881237a43ab8 ffffffff815e237b
kernel: ffff881237a43ad0 ffffffff814cd4ca ffff8829ec71eb00 ffff881237a43af0
kernel: ffffffff814c6232 0000000000000286 ffff8829ec71eb00 ffff881237a43b00
kernel: Call Trace:
kernel: <IRQ>  [<ffffffff815e237b>] dump_stack+0x19/0x1b
kernel: [<ffffffff814cd4ca>] netdev_rx_csum_fault+0x3a/0x40
kernel: [<ffffffff814c6232>] __skb_checksum_complete_head+0x62/0x70
kernel: [<ffffffff814c6251>] __skb_checksum_complete+0x11/0x20
kernel: [<ffffffff8155a20c>] nf_ip_checksum+0xcc/0x100
kernel: [<ffffffffa049edc7>] icmp_error+0x1f7/0x35c [nf_conntrack_ipv4]
kernel: [<ffffffff814cf419>] ? netif_rx+0xb9/0x1d0
kernel: [<ffffffffa040eb7b>] ? internal_dev_recv+0xdb/0x130 [openvswitch]
kernel: [<ffffffffa04c8330>] nf_conntrack_in+0xf0/0xa80 [nf_conntrack]
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffffa049e302>] ipv4_conntrack_in+0x22/0x30 [nf_conntrack_ipv4]
kernel: [<ffffffff815005ca>] nf_iterate+0xaa/0xc0
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffff81500664>] nf_hook_slow+0x84/0x140
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffff81509dd4>] ip_rcv+0x344/0x380

Hardware verifies IP & tcp/udp header checksum but does not provide payload
checksum, use CHECKSUM_UNNECESSARY. Set it only if its valid IP tcp/udp packet.

Cc: Jiri Benc <jbenc@redhat.com>
Cc: Stefan Assmann <sassmann@redhat.com>
Reported-by: NSunil Choudhary <schoudha@redhat.com>
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Reviewed-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for setting/getting rss hash key using ethtool.

v2:
respin patch to support RSS hash function changes.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use of well known RSS key might increase attack surface.

Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Govindarajulu Varadarajan <_govind@gmx.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the access to wq has been moved out of hardirq context. We no longer need to
use spin_lock_irqsave.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

enic_isr_legacy(), enic_isr_msix() & enic_isr_msi() run from hard
interrupt context.

They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check and update posted_index only when skb->xmit_more is 0 or tx queue is full.

v2:
use txq_map instead of skb_get_queue_mapping(skb)
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the commit d75b1ade ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. In tx napi poll we always return 0.
So tx napi is not called again and we do not clean up the tx ring.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we reuse the rx buffer, we need to update the desc. If not hardware sees
stale value.

In the following crash, when mtu is changed, hardware sees old rx buffer value
and crashes on skb_put.

Fix this by using enic_queue_rq_desc helper function which updates the necessary
desc.

[   64.657376] skbuff: skb_over_panic: text:ffffffffa041f55d len:9010 put:9010 head:ffff8800d3ca9fc0 data:ffff8800d3caa000 tail:0x2372 end:0x640 dev:enp0s3
[   64.659965] ------------[ cut here ]------------
[   64.661322] kernel BUG at net/core/skbuff.c:100!
[   64.662644] invalid opcode: 0000 [#1] PREEMPT SMP
[   64.664001] Modules linked in: rpcsec_gss_krb5 auth_rpcgss oid_registry nfsv4 cirrus ttm drm_kms_helper drm enic psmouse microcode evdev serio_raw syscopyarea sysfillrect sysimgblt i2c_piix4 i2c_core pcspkr nfs lockd grace sunrpc fscache ext4 crc16 mbcache jbd2 sd_mod ata_generic virtio_balloon ata_piix libata uhci_hcd virtio_pci virtio_ring usbcore usb_common virtio scsi_mod
[   64.664834] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W      3.17.0-netnext-10335-g942396b0-dirty #273
[   64.664834] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[   64.664834] task: ffffffff81a1d580 ti: ffffffff81a00000 task.ti: ffffffff81a00000
[   64.664834] RIP: 0010:[<ffffffff81392cf1>]  [<ffffffff81392cf1>] skb_panic+0x61/0x70
[   64.664834] RSP: 0018:ffff880210603d48  EFLAGS: 00010292
[   64.664834] RAX: 000000000000008c RBX: ffff88020b0f6930 RCX: 0000000000000000
[   64.664834] RDX: 000000000000008c RSI: ffffffff8178b288 RDI: 00000000ffffffff
[   64.664834] RBP: ffff880210603d68 R08: 0000000000000001 R09: 0000000000000001
[   64.664834] R10: 00000000000005ce R11: 0000000000000001 R12: ffff88020b1f0b40
[   64.664834] R13: 000000000000a332 R14: ffff880209a1a000 R15: 0000000000000001
[   64.664834] FS:  0000000000000000(0000) GS:ffff880210600000(0000) knlGS:0000000000000000
[   64.664834] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   64.664834] CR2: 00007f6752935e48 CR3: 0000000035743000 CR4: 00000000000006f0
[   64.664834] Stack:
[   64.664834]  ffff8800d3caa000 0000000000002372 0000000000000640 ffff88020b1f0000
[   64.664834]  ffff880210603d78 ffffffff81392d54 ffff880210603e08 ffffffffa041f55d
[   64.664834]  0000000000000296 ffffffff00000000 00008e7e00008e7e ffff880200002332
[   64.664834] Call Trace:
[   64.664834]  <IRQ>
[   64.664834]
[   64.664834]  [<ffffffff81392d54>] skb_put+0x54/0x60
[   64.664834]  [<ffffffffa041f55d>] enic_rq_service.constprop.47+0x3ad/0x730 [enic]
[   64.664834]  [<ffffffffa041fa79>] enic_poll_msix_rq+0x199/0x370 [enic]
[   64.664834]  [<ffffffff813a5499>] net_rx_action+0x139/0x210
[   64.664834]  [<ffffffff81290db3>] ? __this_cpu_preempt_check+0x13/0x20
[   64.664834]  [<ffffffff8106110e>] __do_softirq+0x14e/0x280
[   64.664834]  [<ffffffff8106152e>] irq_exit+0x8e/0xb0
[   64.664834]  [<ffffffff8100fd21>] do_IRQ+0x61/0x100
[   64.664834]  [<ffffffff814a2bf2>] common_interrupt+0x72/0x72

fixes: a03bb56e ("enic: implement rx_copybreak")
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error in rx path, we free the buf->os_buf but we do not make it NULL.
In next iteration we use the skb which is already freed. This causes the
following crash.

[  886.154772] general protection fault: 0000 [#1] PREEMPT SMP
[  886.154851] Modules linked in: rpcsec_gss_krb5 auth_rpcgss oid_registry nfsv4 microcode evdev cirrus ttm drm_kms_helper drm enic syscopyarea sysfillrect sysimgblt psmouse i2c_piix4 serio_raw pcspkr i2c_core nfs lockd grace sunrpc fscache ext4 crc16 mbcache jbd2 sd_mod crc_t10dif crct10dif_common ata_generic ata_piix virtio_balloon libata scsi_mod uhci_hcd usbcore virtio_pci virtio_ring virtio usb_common
[  886.155199] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W      3.17.0-netnext-05668-g876bc7f #272
[  886.155263] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[  886.155304] task: ffffffff81a1d580 ti: ffffffff81a00000 task.ti: ffffffff81a00000
[  886.155356] RIP: 0010:[<ffffffff81384030>]  [<ffffffff81384030>] kfree_skb_list+0x10/0x30
[  886.155418] RSP: 0018:ffff880210603d48  EFLAGS: 00010206
[  886.155456] RAX: 0000000000000020 RBX: 0000000000000000 RCX: 0000000000000000
[  886.155504] RDX: 0000000000000000 RSI: 0000000000000001 RDI: 004500084e000017
[  886.155553] RBP: ffff880210603d50 R08: 00000000fe13d1b6 R09: 0000000000000001
[  886.155601] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880209ff2f00
[  886.155650] R13: ffff88020ac0fe40 R14: ffff880209ff2f00 R15: ffff8800da8e3a80
[  886.155699] FS:  0000000000000000(0000) GS:ffff880210600000(0000) knlGS:0000000000000000
[  886.155774] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[  886.155814] CR2: 00007f0e0c925000 CR3: 0000000035e8b000 CR4: 00000000000006f0
[  886.155865] Stack:
[  886.155882]  0000000000000000 ffff880210603d78 ffffffff81383f79 ffff880209ff2f00
[  886.155942]  ffff88020b0c0b40 000000000000c000 ffff880210603d90 ffffffff81383faf
[  886.156001]  ffff880209ff2f00 ffff880210603da8 ffffffff8138406d ffff88020b1b08c0
[  886.156061] Call Trace:
[  886.156080]  <IRQ>
[  886.156095]
[  886.156112]  [<ffffffff81383f79>] skb_release_data+0xa9/0xc0
[  886.157656]  [<ffffffff81383faf>] skb_release_all+0x1f/0x30
[  886.159195]  [<ffffffff8138406d>] consume_skb+0x1d/0x40
[  886.160719]  [<ffffffff813942e5>] __dev_kfree_skb_any+0x35/0x40
[  886.162224]  [<ffffffffa02dc1d5>] enic_rq_service.constprop.47+0xe5/0x5a0 [enic]
[  886.163756]  [<ffffffffa02dc829>] enic_poll_msix_rq+0x199/0x370 [enic]
[  886.164730]  [<ffffffff81397e29>] net_rx_action+0x139/0x210
[  886.164730]  [<ffffffff8105fb2e>] __do_softirq+0x14e/0x280
[  886.164730]  [<ffffffff8105ff2e>] irq_exit+0x8e/0xb0
[  886.164730]  [<ffffffff8100fc1d>] do_IRQ+0x5d/0x100
[  886.164730]  [<ffffffff81496832>] common_interrupt+0x72/0x72

fixes: a03bb56e ("enic: implement rx_copybreak")
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In enic_stop, we disable preemption using local_bh_disable(). We disable
preemption to wait for busy_poll to finish.

napi_disable should not be called here as it might sleep.

Moving napi_disable() call out side of local_bh_disable.

BUG: sleeping function called from invalid context at include/linux/netdevice.h:477
in_atomic(): 1, irqs_disabled(): 0, pid: 443, name: ifconfig
INFO: lockdep is turned off.
Preemption disabled at:[<ffffffffa029c5c4>] enic_rfs_flw_tbl_free+0x34/0xd0 [enic]

CPU: 31 PID: 443 Comm: ifconfig Not tainted 3.17.0-netnext-05504-g59f35b81 #268
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
 ffff8800dac10000 ffff88020b8dfcb8 ffffffff8148a57c 0000000000000000
 ffff88020b8dfcd0 ffffffff8107e253 ffff8800dac12a40 ffff88020b8dfd10
 ffffffffa029305b ffff88020b8dfd48 ffff8800dac10000 ffff88020b8dfd48
Call Trace:
 [<ffffffff8148a57c>] dump_stack+0x4e/0x7a
 [<ffffffff8107e253>] __might_sleep+0x123/0x1a0
 [<ffffffffa029305b>] enic_stop+0xdb/0x4d0 [enic]
 [<ffffffff8138ed7d>] __dev_close_many+0x9d/0xf0
 [<ffffffff8138ef81>] __dev_close+0x31/0x50
 [<ffffffff813974a8>] __dev_change_flags+0x98/0x160
 [<ffffffff81397594>] dev_change_flags+0x24/0x60
 [<ffffffff814085fd>] devinet_ioctl+0x63d/0x710
 [<ffffffff81139c16>] ? might_fault+0x56/0xc0
 [<ffffffff81409ef5>] inet_ioctl+0x65/0x90
 [<ffffffff813768e0>] sock_do_ioctl+0x20/0x50
 [<ffffffff81376ebb>] sock_ioctl+0x20b/0x2e0
 [<ffffffff81197250>] do_vfs_ioctl+0x2e0/0x500
 [<ffffffff81492619>] ? sysret_check+0x22/0x5d
 [<ffffffff81285f23>] ? __this_cpu_preempt_check+0x13/0x20
 [<ffffffff8109fe19>] ? trace_hardirqs_on_caller+0x119/0x270
 [<ffffffff811974ac>] SyS_ioctl+0x3c/0x80
 [<ffffffff814925ed>] system_call_fastpath+0x1a/0x1f
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following warning is shown when spinlock debug is enabled.

This occurs when enic_flow_may_expire timer function is running and
enic_stop is called on same CPU.

Fix this by using spink_lock_bh().

=================================
[ INFO: inconsistent lock state ]
3.17.0-netnext-05504-g59f35b81 #268 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
ifconfig/443 [HC0[0]:SC0[0]:HE1:SE1] takes:
 (&(&enic->rfs_h.lock)->rlock){+.?...}, at:
enic_rfs_flw_tbl_free+0x34/0xd0 [enic]
{IN-SOFTIRQ-W} state was registered at:
  [<ffffffff810a25af>] __lock_acquire+0x83f/0x21c0
  [<ffffffff810a45f2>] lock_acquire+0xa2/0xd0
  [<ffffffff814913fc>] _raw_spin_lock+0x3c/0x80
  [<ffffffffa029c3d5>] enic_flow_may_expire+0x25/0x130[enic]
  [<ffffffff810bcd07>] call_timer_fn+0x77/0x100
  [<ffffffff810bd8e3>] run_timer_softirq+0x1e3/0x270
  [<ffffffff8105f9ae>] __do_softirq+0x14e/0x280
  [<ffffffff8105fdae>] irq_exit+0x8e/0xb0
  [<ffffffff8103da0f>] smp_apic_timer_interrupt+0x3f/0x50
  [<ffffffff81493742>] apic_timer_interrupt+0x72/0x80
  [<ffffffff81018143>] default_idle+0x13/0x20
  [<ffffffff81018a6a>] arch_cpu_idle+0xa/0x10
  [<ffffffff81097676>] cpu_startup_entry+0x2c6/0x330
  [<ffffffff8103b7ad>] start_secondary+0x21d/0x290
irq event stamp: 2997
hardirqs last  enabled at (2997): [<ffffffff81491865>] _raw_spin_unlock_irqrestore+0x65/0x90
hardirqs last disabled at (2996): [<ffffffff814915e6>] _raw_spin_lock_irqsave+0x26/0x90
softirqs last  enabled at (2968): [<ffffffff813b57a3>] dev_deactivate_many+0x213/0x260
softirqs last disabled at (2966): [<ffffffff813b5783>] dev_deactivate_many+0x1f3/0x260

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&enic->rfs_h.lock)->rlock);
  <Interrupt>
    lock(&(&enic->rfs_h.lock)->rlock);

 *** DEADLOCK ***
Reported-by: NJan Stancek <jstancek@redhat.com>
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the much more common pr_warn instead of pr_warning.

Other miscellanea:

o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for setting/getting rx_copybreak using
generic ethtool tunable.

Defines enic_get_tunable() & enic_set_tunable() to get/set rx_copybreak.
As of now, these two function supports only rx_copybreak.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: NBenoit Taine <benoit.taine@lip6.fr>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Remove the now unnecessary memset too.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Govindarajulu Varadarajan <_govind@gmx.com>
Cc: Neel Patel <neepatel@cisco.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch impliments ethtool_ops->get_rxnfc() to display the classifier
filter added by the driver.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the #ifdef CONFIG_RFS_ACCEL around the classifier filter
structures. This makes the filter structures available when CONFIG_RFS_ACCEL = n.

Introduce enic_rfs_timer_start() & enic_rfs_timer_stop() to start/stop the
timer. These two functions are nop when CONFIG_RFS_ACCEL = n.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

enic_set_coalesce() has two problems.

* It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values.

* In case of MSIX, enic_set_coalesce return error after applying requested
  coalescing setting partially. We should either apply all the setting requeste
  and return success or apply non and return error.

* This patch also simplifies the algo.

This was introduced by
'7c2ce6e6 enic: Add support for adaptive interrupt coalescing'

These changes were suggested by Ben Hutchings here
http://www.spinics.net/lists/netdev/msg283972.html

Also change enic driver version.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_RFS_ACCEL=n:

drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_open':
drivers/net/ethernet/cisco/enic/enic_main.c:1603:2: error: implicit declaration of function 'enic_rfs_flw_tbl_init' [-Werror=implicit-function-declaration]
drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_stop':
drivers/net/ethernet/cisco/enic/enic_main.c:1630:2: error: implicit declaration of function 'enic_rfs_flw_tbl_free' [-Werror=implicit-function-declaration]

Introduced in commit a145df23 ("enic: Add
Accelerated RFS support").

Dummy functions are provided, but their prototypes are missing, causing the
build failure.  Provide dummy static inline functions instead to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Till now enic had been doing tx clean in isr.

Using napi infrastructure to move the tx clean up out of isr to softirq.
Now, wq isr schedules napi poll. In enic_poll_msix_wq we clean up the tx queus.

This is applicable only on MSIX. In INTx and MSI we use single napi to clean
both rx & tx queues.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for low latency busy_poll.

* Introduce drivers ndo_busy_poll function enic_busy_poll, which is called by
socket waiting for data.

* Introduce locking between napi_poll nad busy_poll

* enic_busy_poll cleans up all the rx pkts possible. While in busy_poll, rq
holds the state ENIC_POLL_STATE_POLL. While in napi_poll, rq holds the state
ENIC_POLL_STATE_NAPI.

* in napi_poll we return if we are in busy_poll. Incase of INTx & msix, we just
service wq and return if busy_poll is going on.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were experiencing occasional "BUG: scheduling while atomic" splats
in our testing. Enabling DEBUG_SPINLOCK and DEBUG_LOCKDEP in the kernel
exposed a lockdep in the enic driver.

enic 0000:0b:00.0 eth2: Link UP

======================================================
[ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
3.12.0-rc1.x86_64-dbg+ #2 Tainted: GF       W
------------------------------------------------------
NetworkManager/4209 [HC0[0]:SC0[2]:HE1:SE0] is trying to acquire:
(&(&enic->devcmd_lock)->rlock){+.+...}, at: [<ffffffffa026b7e4>] enic_dev_packet_filter+0x44/0x90 [enic]

The fix was to replace spin_lock with spin_lock_bh for the enic
devcmd_lock, so that soft irqs would be disabled while the lock
is held.
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NTony Camuso <tcamuso@redhat.com>
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds supports for Accelerated Receive Flow Steering.

When the desired rx is different from current rq, for a flow, kernel calls the
driver function enic_rx_flow_steer(). enic_rx_flow_steer adds a IP-TCP/UDP
hardware filter.

Driver registers a timer function enic_flow_may_expire. This function is called
every HZ/4 seconds. In this function we check if the added filter has expired
by calling rps_may_expire_flow(). If the flow has expired, it removes the hw
filter.

As of now adaptor supports only IPv4 - TCP/UDP filters.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rx_cpu_rmap provides the reverse irq cpu affinity. This patch allocates and
sets drivers netdev->rx_cpu_rmap accordingly.

rx_cpu_rmap is set in enic_request_intr() which is called by enic_open and
rx_cpu_rmap is freed in enic_free_intr() which is called by enic_stop.

This is used by Accelerated RFS.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds interface to add and delete IP 5 tuple filter. This interface
is used by Accelerated RFS code to steer a flow to corresponding receive
queue.

As of now adaptor supports only ipv4 + tcp/udp packet steering.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware (in readq(&devcmd->args[0])) returns positive number in case of error.
But _vnic_dev_cmd should return a negative value in case of error.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change updates the enic driver to make use of __dev_uc_sync and
__dev_mc_sync calls.  Previously the driver was doing its own list
management by storing the mc_addr and uc_addr list in a 32 address array.
With this change the sync data is stored in the netdev_addr_list structures
and instead we just track how many addresses we have written to the device.
When we encounter 32 we stop and print a message as occurred previously with
the old approach.

Other than the core change the only other bit needed was to propagate the
constant attribute with the MAC address as there were several spots where
is twas only passed as a u8 * instead of a const u8 *.

This patch is meant to maintain the original functionality without the use
of the mc_addr and uc_addr arrays.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Division of a 32 bit number by a 64 bit number causes the following link
error introduced by
7c2ce6e6 "enic: Add support for adaptive interrupt coalescing"

drivers/built-in.o: In function `enic_poll_msix':
enic_main.c:(.text+0x48710a): undefined reference to `__udivdi3'
make: *** [vmlinux] Error 1

Since numerator is 32 bit, convert denominator to 32 bit accordingly.

Fixes: 7c2ce6e6 ("enic: Add support for adaptive interrupt coalescing")
Reported-by: NJim Davis <jim.epost@gmail.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for adaptive interrupt coalescing.

For small pkts with low pkt rate, we can decrease the coalescing interrupt
dynamically which decreases the latency. This however increases the cpu
utilization. Based on testing with different coal intr and pkt rate we came up
with a table(mod_table) with rx_rate and coalescing interrupt value where we
get low latency without significant increase in cpu. mod_table table stores
the coalescing timer percentage value for different throughputs.

Function enic_calc_int_moderation() calculates the desired coalescing intr timer
value. This function is called in driver rx napi_poll. The actual value is set
by enic_set_int_moderation() which is called when napi_poll is complete. i.e
when we unmask the rx intr.

Adaptive coal intr is support only when driver is using msix intr. Because
intr is not shared.

Struct mod_range is used to store only the default adaptive coalescing intr
value.

Adaptive coal intr calue is calculated by

timer = range_start + ((rx_coal->range_end - range_start) *
		       mod_table[index].range_percent / 100);

rx_coal->range_end is the rx-usecs-high value set using ethtool.
range_start is rx-usecs-low, set using ethtool, if rx_small_pkt_bytes_cnt is
greater than 2 * rx_large_pkt_bytes_cnt. i.e small pkts are dominant. Else its
rx-usecs-low + 3.

Cc: Christian Benvenuti <benve@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The enic driver fails to build on ARM with:

In file included from drivers/net/ethernet/cisco/enic/enic_res.c:40:0:
drivers/net/ethernet/cisco/enic/enic.h:48:2: error: expected specifier-qualifier-list before 'irqreturn_t'
  irqreturn_t (*isr)(int, void *);
  ^

Nothing in the driver is explicitly including the irq definitions, so we add
an include of linux/irq.h to pick them up.
Signed-off-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in enic_hard_start_xmit
that can be called in hard irq and other contexts.

enic_hard_start_xmit only frees the skb when dropping it.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: NGovindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Acked-by: NGovindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>