wm5110 rev D is the first chip to use headphone detection IP 2, specify
such and make a small correction as the impedance value is actually read
in 0.5 ohm increments now.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

No point in revisiting ranges the detection will be no more accurate
the second time simply report that the resistance is right on the
range boundry.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

The microphone detection code is run as delayed work to provide
additional debounce, it is possible that the jack could have been
removed by the time we process the microphone detection. Turn this
case into a no op.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

We need to make sure we reset back to our starting state, especially
making sure that we have disabled poll in the register cache.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Improve readability by creating a define for each microphone detection
level.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

In the case of a device tree system there will be no pdata attached to
the device, causing us to deference a NULL pointer. Better to take the
pdata from the Arizona structure as this will always exist and we know
will have been populated since it is populated by the MFD device which
binds in the extcon driver.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

This patch remove extcon_dev_register()'s second parameter which means
the pointer of parent device to simplify prototype of this function.
So, if extcon device has the parent device, it should set the pointer of
parent device to edev.dev.parent in extcon device driver instead of in
extcon_dev_register().

Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

Every other pdata field is specified unshifted the patch handles
shifting for the MICBIAS from the microphone detection polarity
configurations in the extcon driver rather than demanding it in
pdata to match other fields.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

We should move range when the measured value is greater than or equal to
the max value not when greater than.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

Fixes an incomplete comment introduced by commit 9c2ba270
("extcon: arizona: Simplify HPDET based identification").
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

We want the trig_sts bits to be cleared in all cases where we consider
the jack detection interrupt to have been handled. Specifically, if a
duplicate detection event was suppressed these bits were not cleared
causing the CODEC to not enter a low power state. This patch clears the
bits on the duplicate detection code path.
Reported-by: NRyo Tsutsui <ryo.tsutsui@wolfsonmicro.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

This fixes up braces coding style issue by using checkpatch script.

Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fix 80 column coding sytle issues by using checkpatch script.

Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

None of the delayed work the driver schedules has particularly short delays
and it is not performance sensitive so let the scheduler run it wherever
is most efficient rather than in a per CPU workqueue by using the system
power efficient workqueue.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Help mitigate against mechanical bounce during the initial detection by
allowing the configuration of an additional debounce on top of that the
hardware does during the initial phase of microphone detection operation.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If the user moves directly from one button to another then we won't get a
no buttons pressed event and will therefore end up reporting that two
buttons are simultaneously pressed which isn't supported by the hardware.
Make sure we clear any existing button reports before reporting any new
ones.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In pathological cases the microphone detection may fail to report, for
example due to a failure to get a stable measurement. Provide a timeout
to cover such cases.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Rather than measuring both HP channels we can simply directly measure the
microphone impedance and then rely on MICDET for final confirmation of the
presence of a suitable microphone. This improves the overall performance
of the identification process.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This extra check makes the procedure take longer and is of marginal use
in identification so do not execute it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Sometimes we can trigger measurements early if contacts are shorted during
a slow insertion. As well as debouncing add further robustness by retrying
if we get a high impedance measurement for headphones as this can indicate
that the headphones were not yet connected.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Occasionally we can trigger an interrupt before we have completed
impedance measurement, although the valid bit will still be set. This
patch spins reading the impedance value until a valid value is seen.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In cases where we see a brief (dis)connection of the jack detection signals
we may see a noop jack insertion or removal where the jack has returned to
the original state by the time the interrupt is serviced. Suppress these
events in order to save work and avoid confusing the rest of the code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure greater reliability by increasing the minimum threashold for
identifying a microphone.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In some designs an external pull won't be needed.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is no need to do this as HPDET identification will cause MICBIAS to
be powered down again.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The Arizona button detection circuit is configurable, allowing the system
integrator to program a range of thresholds for the buttons supported on
the accessory but currently the driver uses the default button ranges and
does not provide any flexibility in how this is exposed to the application
layer.

Provide platform data allowing the user to control this and to map
the buttons to keys in the input subsystem.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In some pathological use cases users may insert an accessory very slowly
causing multiple indeterminate measurements. Handle this by retrying many
measurements before we give up and declare a headphone.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.

For extcon instead of checking if the headphone output is enabled when
doing magic application unconditionally disable the output and restore
the state which ASoC wants set when undoing the magic.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We have a very similar sequence doing magic writes in several places
(one of which missed an update to interlock with the CODEC driver) so
factor it out into a function.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When using HPDET to identify the accessory still run MICDET before we
report a microphone in order to ensure that the accessory identified is
compatible with the MICDET detection ranges after having confirmed that
the device is not using a headphone.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This should always be the most accurate reading for supported accessory
configurations.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It is important to clear the wake trigger status bits otherwise DCVDD
will be held high independent of the state of the LDOENA line.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The magic is already done as part of enabling the headphone output so
does not need to be done when the headphone outputs are enabled. We hold
the DAPM lock so the headphone status can't be changed underneath us.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The HPDET identification method does not have the same natural debounce
built into it that the standard MICDET method does so add some extra on
top of what the jack detection does in hardware to make sure we get a
robust result.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When starting microphone detection some headsets should be exposed to
the fully regulated microphone bias in order to ensure that they behave
in an optimal fashion.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow systems to tune detection rate and debounce suitably for their
mechanical parameters.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>