- 13 5月, 2010 8 次提交
-
-
由 Bruce Allan 提交于
In MSI-X mode when an IMPI SoL session was active (i.e. the PHY reset was blocked), the LSC interrupt generated by s/w to start the watchdog which started the transmitter was not getting fired by the hardware because bit 24 (the 'other' cause bit) also needed to be set. Without an active SoL session, the PHY was reset which caused the h/w to fire the LSC interrupt. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
82574/82583 uses different registers/bits to setup manageability filters than all other parts supported by e1000e; set them accordingly for IPMI pass-through. Rename the function to better reflect what it does. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
When running ethtool online diagnostics with no open interface, there is a short period of time where the driver relinquishes control of the adapter during which time AMT (manageability firmware) can put the adapter into an unknown state resulting in such things as link test failure, hardware hang, reporting an incorrect link speed, etc. Resetting the adapter during an open() resolves this by putting the adapter into a quiescent state. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
A couple stack cleanups missed in an earlier patch from Jesse. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Amit Kumar Salecha 提交于
Check the access by tools for hardware queue engine and handle it separately than other block registers, otherwise incorrect data is returned. Support for only NX3031 based cards. Acked-by: NDhananjay Phadke <dhananjay.phadke@qlogic.com> Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sucheta Chakraborty 提交于
Remove unnecessary remap of the region in bar 0 to access onhip memory for NX3031. Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sucheta Chakraborty 提交于
NX3031 have 64bit on card memory. Fix the limit check to 64MB and remove unnecessary 128bit read/write check. Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Amit Kumar Salecha 提交于
o For NX3031, MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers are obsolete. These register addresses can be used for different purpose. Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 5月, 2010 10 次提交
-
-
由 Andrew Morton 提交于
i915_error_object_create() is called from the timer interrupt and hence can corrupt the KM_USER0 slot. Use KM_IRQ0 instead. Reported-by: NJaswinder Singh Rajput <jaswinderlinux@gmail.com> Tested-by: NJaswinder Singh Rajput <jaswinderlinux@gmail.com> Acked-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Dave Airlie <airlied@linux.ie> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Oliver Neukum 提交于
The work queue has to be flushed after the device has been made inaccessible. The patch closes a window during which a work queue might remain active after the device is removed and would then lead to ACPI calls with undefined behavior. Signed-off-by: NOliver Neukum <oneukum@suse.de> Acked-by: NEric Piel <eric.piel@tremplin-utc.net> Acked-by: NPavel Machek <pavel@ucw.cz> Cc: Pavel Herrmann <morpheus.ibis@gmail.com> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Michael Hennerich 提交于
The current allocation does not include the memory required for blanking lines. So avoid memory corruption when multiple devices are using the DMA memory near each other. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Nicolas Ferre 提交于
In debugfs, printing of command response reports resp[2] twice: fix it to resp[3]. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Nicolas Ferre 提交于
Disable data error interrupts while we are actually recording that there is not such errors. This will prevent, in some cases, the warning message printed at new request queuing (in atmci_start_request()). Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Nicolas Ferre 提交于
The removing of an SD card in certain circumstances can lead to a kernel oops if we do not make sure that the "data" field of the host structure is valid. This patch adds a test in atmci_dma_cleanup() function and also calls atmci_stop_dma() before throwing away the reference to data. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Nicolas Ferre 提交于
Two parameters were swapped in the calls to atmci_init_slot(). Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Reported-by: NAnders Grahn <anders.grahn@hd-wireless.se> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Denis Turischev 提交于
The SIO chip contains 16 possible gpio lines, not 14. The schematic was not read carefully. Signed-off-by: NDenis Turischev <denis@compulab.co.il> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Stephen Rothwell 提交于
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alex Chiang 提交于
Duplicate entries ended up acpisleep_dmi_table[] by accident. They don't hurt functionality, but they are ugly, so let's get rid of them. Cc: stable@kernel.org Signed-off-by: NAlex Chiang <achiang@canonical.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 11 5月, 2010 20 次提交
-
-
由 Henrik Rydberg 提交于
The current code will not remove the sysfs files for fan numbers three and up. Also, upon exit, fans one and two are removed regardless of their existence. This patch cleans up the sysfs error handling for the fans. Signed-off-by: NHenrik Rydberg <rydberg@euromail.se> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Ken Milmore 提交于
* Allow fan minimum RPM to be set to zero without triggering alarms. * Fix voltage scaling arithmetic and correct scale factors. * Correct fan1-fan4 alarm bit shifts. * Correct register address for temp3_smoothing_enable. * Read the alarm registers with high priority. Signed-off-by: NKen Milmore <ken.milmore@googlemail.com> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Jean Delvare 提交于
Commit b4fe9454 introduced 3 bugs, fix them: * Use the right command dword for second packet offset in RADEON_CNTL_PAINT/BITBLT_MULTI. * Don't leak memory if drm_buffer_copy_from_user() fails. * Don't call drm_buffer_unprocessed() unless drm_buffer_alloc() and drm_buffer_copy_from_user() have been called successfully first. Signed-off-by: NJean Delvare <khali@linux-fr.org> Cc: Pauli Nieminen <suokkos@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Randy Dunlap 提交于
When CONFIG_NET is disabled, the attempt to build wext-priv.c fails with: net/wireless/wext-priv.c: In function 'ioctl_private_call': net/wireless/wext-priv.c:207: error: implicit declaration of function 'call_commit_handler' Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Xose Vazquez Perez 提交于
s/X/x Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
With a little bit of restructuring it isn't necessary to have special cases in rt2x00queue_write_tx_descriptor for writing the descriptor for beacons. Simply split off the kicking of the TX queue to a separate function with is only called for non-beacons. Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
According to the Ralink vendor driver for rt2800 we don't need a full TXD for a beacon but just a TXWI in front of the actual beacon. Fix the rt2800pci and rt2800usb beaconing code accordingly. Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
Preparation to fix rt2800 beaconing. Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
All of the driver's kick_tx_queue callback functions treat the TX queue for beacons in a special manner. Clean this up by integrating the kicking of the beacon queue into the write_beacon callback function, and let the generic code no longer call the kick_tx_queue callback function when updating the beacon. Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
RXWI processing is exactly the same for rt2800pci and rt2800usb, so make it common code. Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
TXWI writing is exactly the same for rt2800pci and rt2800usb, so make it common code. Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
We should simply follow what the hardware told us it has done. Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
Remove unused RXD_DESC_SIZE define and remove duplicated RXWI definitions from rt2800.h. Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gertjan van Wingerde 提交于
We should take the stripping of the IV into account for the txdesc->length field. Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Tested-by: NPavel Roskin <proski@gnu.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
There are several places that use > ARRAY_SIZE() instead of >= ARRAY_SIZE(). Signed-off-by: NDan Carpenter <error27@gmail.com> Acked-by: NBob Copeland <me@bobcopeland.com> Acked-by: NBruno Randolf <br1@einfach.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
I changed "> ATH9K_HTC_MAX_TID" to ">= ATH9K_HTC_MAX_TID" to avoid a potential overflow. Signed-off-by: NDan Carpenter <error27@gmail.com> Acked-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
This is a stray null dereference. We initialize "ista" properly later on. Signed-off-by: NDan Carpenter <error27@gmail.com> Acked-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
This mutex_unlock() has been here from the initial commit, but as nearly as I can tell, there isn't a reason for it. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
Cc: Paul Shaw <paul.shaw@atheros.com> Cc: Don Breslin <don.breslin@atheros.com> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
From the original report: "I had problems to get my rtl8185 PCI card running on Sparc64: I always got an error about "No suitable DMA available" followed by an error that no device could be detected. When comparing the rtl8180 driver to others I noticed that others are mostly using DMA_BIT_MASK so I changed the custom mask to DMA_BIT_MASK(32) which fixed my issue." Reported-by: NTiziano Müller <tm@dev-zero.ch> Acked-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 10 5月, 2010 2 次提交
-
-
由 Eric Dumazet 提交于
Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bing Zhao 提交于
Get the device type from MODULE_BRINGUP_REQ command response. Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-