If ARM_MT8173_CPUFREQ is configured, and THERMAL is configured as module,
the following build error is seen for arm:allmodconfig and
arm64:allmodconfig.

drivers/built-in.o: In function `mtk_cpufreq_ready':
:(.text+0x32a20c): undefined reference to `of_cpufreq_cooling_register'
drivers/built-in.o: In function `mtk_cpufreq_exit':
:(.text+0x32a420): undefined reference to `cpufreq_cooling_unregister'

The fix is similar to CPUFREQ_DT, but more restrictive since
ARM_MT8173_CPUFREQ can not be built as module.

Fixes: 1453863f ("cpufreq: mediatek: Add MT8173 cpufreq driver")
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Tolerance applies on both sides of the target voltage, i.e. both min and
max sides. But while checking if a voltage is supported by the regulator
or not, we haven't taken care of tolerance on the lower side. Fix that.

Cc: Lucas Stach <l.stach@pengutronix.de>
Fixes: 045ee45c ("cpufreq: cpufreq-dt: disable unsupported OPPs")
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

We need to explicitly mark OPPs as shared, when they are not defined
with OPP-v2 bindings. This operation can potentially fail, and in that
case we should at least print an error message.

Fixes: 2e02d872 ("cpufreq: dt: Add support for operating-points-v2 bindings")
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

We need to explicitly mark OPPs as shared, when they are not defined
with OPP-v2 bindings. But this isn't required to be done if we failed to
initialize OPP table.

Reorder code to verify OPP count before marking them shared.

Fixes: 2e02d872 ("cpufreq: dt: Add support for operating-points-v2 bindings")
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Wall time obtained from do_gettimeofday is susceptible to sudden jumps due to
user setting the time or due to NTP.

Monotonic time is constantly increasing time better suited for comparing two
timestamps.
Signed-off-by: NAbhilash Jindal <klock.android@gmail.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Modify the OCC reset/load/active event message to make it clearer for
the user to understand the event and effect of the event.
Suggested-by: NStewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: NShilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Driver is guaranteed to be present on a call to cpufreq_parse_governor()
and there is no need to check for !cpufreq_driver. Drop it.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Its all about caching min/max freq requested by userspace, and
the name 'cpufreq_real_policy' doesn't fit that well. Rename it to
cpufreq_user_policy.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Its always same as policy->policy, and there is no need to keep another
copy of it. Remove it.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Its always same as policy->governor, and there is no need to keep
another copy of it. Remove it.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

'user_policy' caches properties of a policy that are set by userspace.
And these must be updated only if cpufreq core was successful in
updating them based on request from user space.

In store_scaling_governor(), we are updating user_policy.policy and
user_policy.governor even if cpufreq_set_policy() failed. That's
incorrect.

Fix this by updating user_policy.* only if we were successful in
updating the properties.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

cpufreq_get_policy() is useful if the pointer to policy isn't available
in advance. But if it is available, then there is no need to call
cpufreq_get_policy(). Directly use memcpy() to copy the policy.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

What's being done from CPUFREQ_INCOMPATIBLE, can also be done with
CPUFREQ_ADJUST. There is nothing special with CPUFREQ_INCOMPATIBLE
notifier.

Kill CPUFREQ_INCOMPATIBLE and fix its usage sites.

This also updates the numbering of notifier events to remove holes.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Mediatek MT8173 is an ARMv8 based quad-core (2*Cortex-A53 and
2*Cortex-A72) SoC with duall clusters. For each cluster, two voltage
inputs, Vproc and Vsram are supplied by two regulators. For the big
cluster, two regulators come from different PMICs. In this case, when
scaling voltage inputs of the cluster, the voltages of two regulator
inputs need to be controlled by software explicitly under the SoC
specific limitation:

	100mV < Vsram - Vproc < 200mV

which is called 'voltage tracking' mechanism. And when scaling the
frequency of cluster clock input, the input MUX need to be parented to
another "intermediate" stable PLL first and reparented to the original
PLL once the original PLL is stable at the target frequency. This patch
implements those mechanisms to enable CPU DVFS support for Mediatek
MT8173 SoC.
Signed-off-by: NPi-Cheng Chen <pi-cheng.chen@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch adds the clock and regulator consumer properties part of
document for CPU DVFS clocks on Mediatek MT8173 SoC.
Signed-off-by: NPi-Cheng Chen <pi-cheng.chen@linaro.org>
Acked-by: NMichael Turquette <mturquette@baylibre.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

IS_ERR(_OR_NULL) already contain an 'unlikely' compiler flag and there
is no need to do that again from its callers. Drop it.
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Dan Carpenter reported (generated with static checker):

drivers/base/power/opp.c:949 _opp_add_static_v2()
warn: passing casted pointer '&new_opp->clock_latency_ns' to
'of_property_read_u32()' 64 vs 32.

This code will break on 64 bit, big endian machines.

Fix this by reading the value in a u32 type variable first and then
assigning it to the unsigned long variable.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Suggested-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

_of_init_opp_table_v2() isn't freeing up resources on some errors and
the error values returned are also not correct always.

This fixes following problems:
- Return -ENOENT, if no entries are found in the table.
- Use IS_ERR() to properly check return value of _find_device_opp().
- Return error value with PTR_ERR() in above case.
- Free table if _find_device_opp() fails.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Make scaling_boost_freqs sysfs attribute is available when
cpufreq-dt driver is used and boost support is enabled.
Suggested-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Append more Oracle X86 servers that have their own power management,

SUN FIRE X4275 M3
SUN FIRE X4170 M3
and
SUN FIRE X6-2
Signed-off-by: NEthan Zhao <ethan.zhao@oracle.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Whitelist the SKL-S processor
Signed-off-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

With opp-v2 DT bindings, few OPPs can be used only for the boost mode.
But using such OPPs require the boost mode to be supported by cpufreq
driver.

We will parse DT bindings only during ->init() and so can enable boost
support only after registering cpufreq driver.

This enables boost support as soon as any policy has boost/turbo OPPs
for its CPUs.

We don't need to disable boost support as that is done by the core, when
the driver is unregistered.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Support for parsing operating-points-v2 bindings is in place now, lets
modify cpufreq-dt driver to use them.

For backward compatibility we will continue to support earlier bindings.
Special handling for that is required, to make sure OPPs are initialized
for all the CPUs.
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

In some cases it wouldn't be known at time of driver registration, if
the driver needs to support boost frequencies.

For example, while getting boost information from DT with opp-v2
bindings, we need to parse the bindings for all the CPUs to know if
turbo/boost OPPs are supported or not.

One way out to do that efficiently is to delay supporting boost mode
(i.e. creating /sys/devices/system/cpu/cpufreq/boost file), until the
time OPP bindings are parsed.

At that point, the driver can enable boost support. This can be done at
->init(), where the frequency table is created.

To do that, the driver requires few APIs from cpufreq core that let him
do this. This patch provides these APIs.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

cpufreq table entries for OPPs with turbo modes enabled, should be
marked with CPUFREQ_BOOST_FREQ flag. This ensures that these states are
only used while operating in boost or turbo mode.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Add dev_pm_opp_is_turbo() helper to verify if an opp is to be used only
for turbo mode or not.
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

With "operating-points-v2" its possible to tell which devices share
OPPs. We already have infrastructure to decode that information.

This patch adds following APIs:
 - of_get_cpus_sharing_opps: Returns cpumask of CPUs sharing OPPs (only
   valid with v2 bindings).
 - of_cpumask_init_opp_table: Initializes OPPs for all CPUs present in
   cpumask.
 - of_cpumask_free_opp_table: Frees OPPs for all CPUs present in cpumask.

 - set_cpus_sharing_opps: Sets which CPUs share OPPs (only valid with old
   OPP bindings, as this information isn't present in DT).
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

With "operating-points-v2" bindings, it's possible to specify the OPP to
which the device must be switched, before suspending.

This patch adds support for getting that information.
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

An opp can be shared by multiple devices, for example its very common
for CPUs to share the OPPs, i.e. when they share clock/voltage rails.

This patch adds support of shared OPPs to the OPP library.

Instead of a single device, dev_opp will now contain a list of devices
that use it. It also senses if the device (we are trying to initialize
OPPs for) shares OPPs with a device added earlier and in that case we
update the list of devices managed by OPPs instead of duplicating OPPs
again.

The same infrastructure will be used for the old OPP bindings, with
later patches.
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

With "operating-points-v2" bindings, clock-latency is defined per OPP.
Users of this value expect a single value which defines the latency to
switch to any clock rate. Find maximum clock-latency-ns from the OPP
table to service requests from such users.
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This adds support in OPP library to parse and create list of OPPs from
operating-points-v2 bindings. It takes care of most of the properties of
new bindings (except shared-opp, which will be handled separately).

For backward compatibility, we keep supporting earlier bindings. We try
to search for the new bindings first, in case they aren't present we
look for the old deprecated ones.

There are few things marked as TODO:
- Support for multiple OPP tables
- Support for multiple regulators

They should be fixed separately.
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Later commits would add support for new OPP bindings and this would be
required then. So, lets do it in a separate patch to make it easily
reviewable.

Another change worth noticing is INIT_LIST_HEAD(&opp->node). We weren't
doing it earlier as we never tried to delete a list node before it is
added to list. But this wouldn't be the case anymore. We might try to
delete a node (just to reuse the same code paths), without it being
getting added to the list.
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

There is no need to complicate _opp_add_dynamic() with allocation of
dev_opp as well. Allocate it from _add_device_opp() instead.
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This will be used from multiple places later. Lets create a separate
routine for that.
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

In order to prepare for the later commits, this relocates few routines
towards the top as they will be used earlier in the code.
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

More platform specific extended opp bindings will follow and it would be
easy to manage them with a directory for opp. Lets create that and move
the existing opp bindings into it.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

With a 32 bit value, the maximum frequency that the bindings can
support is ~ 4 GHz. And that might fall short of what newer systems may
have.

Allow opp-hz to be a 64 bit big-endian value.
Suggested-by: NStephen Boyd <sboyd@codeaurora.org>
Suggested-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>