* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: (f75375s) Remove unnecessary and confusing initialization
  hwmon: (it87) Properly decode -128 degrees C temperature
  hwmon: (lm90) Document support for the MAX6648/6692 chips
  hwmon: (abituguru3) Fix I/O error handling

Trivial patch to fix bad links in the ext2 and ext3 documentation.
Signed-off-by: NJody McIntyre <scjody@sun.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'fixes-20090312' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/pci:
  PCIe: portdrv: call pci_disable_device during remove
  pci: Fix typo in message while disabling HT MSI mapping
  pci: don't disable too many HT MSI mapping
  powerpc/pseries: The RPA PCI hotplug driver depends on EEH
  PCIe: AER: during disable, check subordinate before walking
  PCI: Add PCI quirk to disable L0s ASPM state for 82575 and 82598

STag zero is a special STag that allows consumers to access any bus
address without registering memory.  The nes driver unfortunately
allows STag zero to be used even with QPs created by unprivileged
userspace consumers, which means that any process with direct verbs
access to the nes device can read and write any memory accessible to
the underlying PCI device (usually any memory in the system).  Such
access is usually given for cluster software such as MPI to use, so
this is a local privilege escalation bug on most systems running this
driver.

The driver was using STag zero to receive the last streaming mode
data; to allow STag zero to be disabled for unprivileged QPs, the
driver now registers a special MR for this data.

Cc: <stable@kernel.org>
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There was a report of a data corruption
http://lkml.org/lkml/2008/11/14/121.  There is a script included to
reproduce the problem.

During testing, I encountered a number of strange things with ext3, so I
tried ext2 to attempt to reduce complexity of the problem.  I found that
fsstress would quickly hang in wait_on_inode, waiting for I_LOCK to be
cleared, even though instrumentation showed that unlock_new_inode had
already been called for that inode.  This points to memory scribble, or
synchronisation problme.

i_state of I_NEW inodes is not protected by inode_lock because other
processes are not supposed to touch them until I_LOCK (and I_NEW) is
cleared.  Adding WARN_ON(inode->i_state & I_NEW) to sites where we modify
i_state revealed that generic_sync_sb_inodes is picking up new inodes from
the inode lists and passing them to __writeback_single_inode without
waiting for I_NEW.  Subsequently modifying i_state causes corruption.  In
my case it would look like this:

CPU0                            CPU1
unlock_new_inode()              __sync_single_inode()
 reg <- inode->i_state
 reg -> reg & ~(I_LOCK|I_NEW)   reg <- inode->i_state
 reg -> inode->i_state          reg -> reg | I_SYNC
                                reg -> inode->i_state

Non-atomic RMW on CPU1 overwrites CPU0 store and sets I_LOCK|I_NEW again.

Fix for this is rather than wait for I_NEW inodes, just skip over them:
inodes concurrently being created are not subject to data integrity
operations, and should not significantly contribute to dirty memory
either.

After this change, I'm unable to reproduce any of the added warnings or
hangs after ~1hour of running.  Previously, the new warnings would start
immediately and hang would happen in under 5 minutes.

I'm also testing on ext3 now, and so far no problems there either.  I
don't know whether this fixes the problem reported above, but it fixes a
real problem for me.

Cc: "Jorge Boncompte [DTI2]" <jorge@dti2.net>
Reported-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Even when page reclaim is under mem_cgroup, # of scan page is determined by
status of global LRU. Fix that.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No software visible difference from revision A.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently we disable the Acer WMI backlight device if there is no ACPI
backlight device.  As a result, we end up with no backlight device at all.
 We should instead disable it if there is an ACPI device, as the other
laptop drivers do.  This regression was introduced in febf2d95 ("Acer-WMI:
fingers off backlight if video.ko is serving this functionality").

Each laptop driver with backlight support got a similar change around
febf2d95.  The changes to the other drivers look correct; see e.g.
a598c82f for a similar but correct change.  The regression is also in
2.6.28.
Signed-off-by: NMichael Spang <mspang@csclub.uwaterloo.ca>
Acked-by: NThomas Renninger <trenn@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>		[2.6.28.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The s3cmci driver is calling s3c2410_dma_config with incorrect data for
the DCON register.  The S3C2410_DCON_HWTRIG is implicit in the channel
configuration and the device selection of S3C2410_DCON_CH0_SDI is
incorrect as the DMA system may not select channel 0.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Acked-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Unfortunately, Linux Foundation funding for my work on
man-pages/testing/doc under the auspices of the LF documentation
fellowship unfortunately ran out a short while ago (after earlier attempts
to seek funding, only Google stepped forward with a bit of further funding
for the position), so the patch below acknowledges something closer to
reality.

Unfortunately, there will (probably very) soon be a further downgrade from
"Maintained" to "Odd Fixes" or "Orphan", unless some funding miracle
occurs.  So, if anyone is looking to become man-pages maintainer, there
may soon be an opening (okay, don't trample me in the rush ;-).)
Signed-off-by: NMichael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The 'battery remaining capacity' calculation in
drivers/power/ds2760_battery.c lacks a parameter check to a division
operation which causes the kernel to oops on my board.

[   21.233750] Division by zero in kernel.
[   21.237646] [<c002955c>] (__div0+0x0/0x20) from [<c012561c>] (Ldiv0+0x8/0x10)
[   21.244816] [<c01bef34>] (ds2760_battery_read_status+0x0/0x2a4) from [<c01bf3a4>] (ds2760_battery_get_property+0x30/0xdc)
[   21.255803]  r8:c03a22c0 r7:c7886100 r6:00000009 r5:c782fe7c r4:c7886084
[   21.262518] [<c01bf374>] (ds2760_battery_get_property+0x0/0xdc) from [<c01bde98>] (power_supply_show_property+0x48/0x114)
[   21.273480]  r6:c7996000 r5:00000009 r4:00000000
[   21.278111] [<c01bde50>] (power_supply_show_property+0x0/0x114) from [<c01be158>] (power_supply_uevent+0x188/0x280)
[   21.288537]  r8:00000001 r7:c7886100 r6:c7996000 r5:000000b4 r4:00000000
[   21.295222] [<c01bdfd0>] (power_supply_uevent+0x0/0x280) from [<c015c664>] (dev_uevent+0xd4/0x10c)
[   21.304199] [<c015c590>] (dev_uevent+0x0/0x10c) from [<c0128440>] (kobject_uevent_env+0x180/0x390)
[   21.313170]  r5:00000000 r4:c78860ac
[   21.316725] [<c01282c0>] (kobject_uevent_env+0x0/0x390) from [<c0128664>] (kobject_uevent+0x14/0x18)
[   21.325850] [<c0128650>] (kobject_uevent+0x0/0x18) from [<c01bdc34>] (power_supply_changed_work+0x5c/0x70)
[   21.335506] [<c01bdbd8>] (power_supply_changed_work+0x0/0x70) from [<c004d290>] (run_workqueue+0xbc/0x144)
[   21.345167]  r4:c7812040
[   21.347716] [<c004d1d4>] (run_workqueue+0x0/0x144) from [<c004d94c>] (worker_thread+0xa8/0xbc)
[   21.356296]  r7:c7812040 r6:c7820b00 r5:c782ffa4 r4:c7812048
[   21.361957] [<c004d8a4>] (worker_thread+0x0/0xbc) from [<c0051008>] (kthread+0x5c/0x94)
[   21.369971]  r7:00000000 r6:c004d8a4 r5:c7812040 r4:c782e000
[   21.375612] [<c0050fac>] (kthread+0x0/0x94) from [<c00403d0>] (do_exit+0x0/0x688)
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: NMatt Reimer <mreimer@vpop.net>
Acked-by: NAnton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In sget(), destroy_super(s) is called with s->s_umount held, which makes
lockdep unhappy.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Menage <menage@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the second fasync_helper() fails, pipe_rdwr_fasync() returns the error
but leaves the file on ->fasync_readers.

This was always wrong, but since 233e70f4
"saner FASYNC handling on file close" we have the new problem.  Because in
this case setfl() doesn't set FASYNC bit, __fput() will not do
->fasync(0), and we leak fasync_struct with ->fa_file pointing to the
freed file.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

W1 master implementations are expected to return 0 or 1 from their
read_bit() function.  However, not all platforms do return these values
from gpio_get_value() - namely PXAs won't.  Hence the w1 gpio-master needs
to break the result down to 0 or 1 itself.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following warning on x86_64:

LD vmlinux.o
MODPOST vmlinux.o
WARNING: vmlinux: 'memcpy' exported twice. Previous export was in vmlinux

For x86_64, this symbol is already exported from arch/um/sys-x86_64/ksyms.c.
Reported-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com>
Tested-by: NBoaz Harrosh <bharrosh@panasas.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It is currently impossible to run a user-mode linux machine inside another
user-mode linux (UML on UML).  It breaks after a few instructions.  When
it tries to check whether SYSEMU is installed (the inner) UML receives an
inconsistent result (from the outer UML).

This is the output of a broken attempt:
$ ./linux mem=256m ubd0=cow
Locating the bottom of the address space ... 0x0
Locating the top of the address space ... 0xc0000000
Core dump limits :
        soft - 0
        hard - NONE
Checking that ptrace can change system call numbers...OK
Checking ptrace new tags for syscall emulation...unsupported
Checking syscall emulation patch for ptrace...check_sysemu : expected SIGTRAP, got status = 256
$

The problem is the following:

PTRACE_SYSCALL/SINGLESTEP is currently managed inside arch_ptrace for ARCH=um.

PTRACE_SYSEMU/SUSEMU_SINGLESTEP is not captured in arch_ptrace's switch,
therefore it is erroneously passed back to ptrace_request (in
kernel/ptrace).

This simple patch simply forces ptrace to return an error on
PTRACE_SYSEMU/SUSEMU_SINGLESTEP as it is unsupported on ARCH=um, and fixes
the problem.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NRenzo Davoli <renzo@cs.unibo.it>
Reviewed-by: NWANG Cong <xiyou.wangcong@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The PCIe port driver calls pci_enable_device() during probe but
never calls pci_disable_device() during remove.

Cc: stable@kernel.org
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

"Enabling" should read "Disabling"
Signed-off-by: NPrakash Punnoor <prakash@punnoor.de>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

Prakash's system needs MSI disabled on some bridges, but not all.
This seems to be the minimal fix for 2.6.29, but should be replaced
during 2.6.30.
Signed-off-by: NPrakash Punnoor <prakash@punnoor.de>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

The RPA PCI hotplug driver calls EEH routines, so should depend on
EEH. Also PPC_PSERIES implies PPC64, so remove that.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

Commit 47a8b0cc (Enable PCIe AER only after checking firmware
support) wants to walk the PCI bus in the remove path to disable
AER, and calls pci_walk_bus for downstream bridges.

Unfortunately, in the remove path, we remove devices and bridges
in a depth-first manner, starting with the furthest downstream
bridge and working our way backwards.

The furthest downstream bridges will not have a dev->subordinate,
and we hit a NULL deref in pci_walk_bus.

Check for dev->subordinate first before attempting to walk the
PCI hierarchy below us.
Acked-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

This patch is intended to disable L0s ASPM link state for 82598 (ixgbe)
parts due to the fact that it is possible to corrupt TX data when coming
back out of L0s on some systems.  The workaround had been added for 82575
(igb) previously, but did not use the ASPM api.  This quirk uses the ASPM
api to prevent the ASPM subsystem from re-enabling the L0s state.

Instead of adding the fix in igb to the ixgbe driver as well it was
decided to move it into a pci quirk.  It is necessary to move the fix out
of the driver and into a pci quirk in order to prevent the issue from
occuring prior to driver load to handle the possibility of the device being
passed to a VM via direct assignment.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sunhme: Fix qfe parent detection.
  sparc64: Fix lost interrupts on sun4u.
  sparc64: wait_event_interruptible_timeout may return -ERESTARTSYS
  jsflash: stop defining MAJOR_NR

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: IP27: Enable RAID5 module
  MIPS: TXx9: update defconfigs
  MIPS: NEC VR5500 processor support fixup
  MIPS: Fix build of non-CONFIG_SYSVIPC version of sys_32_ipc

f75375_probe calls i2c_get_clientdata to initialize the data pointer,
but there isn't yet any client data to get, and the value is never
used before the variable is assigned a new value seven lines later.

The call doesn't hurt anything and wastes only a couple of cycles.
The reason to fix it is because this module serves as an example to
hackers writing new hwmon drivers, and this part of the example is
confusing.
Signed-off-by: NAndrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The it87 driver is reporting -128 degrees C as +128 degrees C.
That's not a terribly likely temperature value but let's still
get it right, especially when it simplifies the code.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Update documentation to prevent further confusion/duplication.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Fix a logic bug reported by Roel Kluin, by rewriting the error
handling code in a clearer way.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: NAlistair John Strachan <alistair@devzero.co.uk>
Acked-by: NHans de Goede <hdegoede@redhat.com>

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: only issues a cache flush on unmount if barriers are enabled
  xfs: prevent lockdep false positive in xfs_iget_cache_miss
  xfs: prevent kernel crash due to corrupted inode log format

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Enable following features:
* MTD (PHYSMAP)
* LED (LEDS_GPIO)
* RBTX4939
* 7SEGLED
* IDE (IDE_TX4938, IDE_TX4939)
* SMC91X
* RTC_DRV_TX4939
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Current VR5500 processor support lacks of some functions which are
expected to be configured/synthesized on arch initialization.

Here're some VR5500A spec notes:

* All execution hazards are handled in hardware.

* Once VR5500A stops the operation of the pipeline by WAIT instruction,
  it could return from the standby mode only when either a reset, NMI
  request, or all enabled interrupts is/are detected.  In other words,
  if interrupts are disabled by Status.IE=0, it keeps in standby mode
  even when interrupts are internally asserted.

  Notes on WAIT: The operation of the processor is undefined if WAIT
  insn is in the branch delay slot.  The operation is also undefined
  if WAIT insn is executed when Status.EXL and Status.ERL are set to 1.

* VR5500A core only implements the Load prefetch.

With these changes, it boots fine.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NXiaotian Feng <xiaotian.feng@windriver.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: fix EDID parser problem with positive/negative hsync/vsync

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  radeonfb/aty128fb: Disable broken early resume hook for PowerBooks
  hvc_console: Remove tty->low_latency on pseries backends
  powerpc: fix linkstation and storcenter compilation breakage
  powerpc/4xx: Enable SERIAL_OF support by default for Virtex platforms

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: fix 945 fence register writes for fence 8 and above.
  drm/i915: Protect active fences on i915
  drm/i915: Check to see if we've pinned all available fences
  drm/i915: Check fence status on every pin.
  drm/i915: First recheck for an empty fence register.
  drm/i915: Fix bad \n in MTRR failure notice.
  drm/i915: Don't restore palettes through VGA registers.
  i915: add newline to i915_gem_object_pin failure msg
  drm: Return EINVAL on duplicate objects in execbuffer object list

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: work around Fedora-11 x86-32 kernel failures on Intel Atom CPUs

On swapon() path, it has already i_mutex. So, this uses i_alloc_sem
instead of it.
Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reported-by: NLaurent GUERBY <laurent@guerby.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The last 8 fence registers sit at a different offset, so when we went to set
fence number 8 in the lower offset, we instead set PGETBL_CTL, and the GPU
got all sorts of angry at us.

fd.o bug #20567.  Easily reproducible by running glxgears and killing it about
6 times.
Signed-off-by: NEric Anholt <eric@anholt.net>

The i915 also uses the fence registers for GPU access to tiled buffers so
we cannot reallocate one whilst it is on the active list. By performing a
LRU scan of the fenced buffers we also avoid waiting the possibility of
waiting on a pinned, or otherwise unusable, buffer.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>