Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This cleans up the eapol frame handling and some related code in the
receive and transmit paths. After this patch
 * EAPOL frames addressed to us or the EAPOL group address are
   always accepted regardless of whether they are encrypted or not
 * other frames from a station are dropped if PAE is enabled and
   the station is not authorized
 * unencrypted frames (except the EAPOL frames above) are dropped if
   drop_unencrypted is enabled
 * some superfluous code that eth_type_trans handles anyway is gone
 * port control is done for transmitted packets
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes mac80211 to verify that VLAN interfaces
are valid and not bother drivers about them any more.
VLAN interfaces are now only valid when an AP interface
is up with the same MAC address, and are automatically
turned off when the AP interface is set down.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.

This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.

Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.

At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().

The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.

Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is nicer than the MAC_FMT stuff.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac80211, remove bitfields from struct ieee80211_sub_if_data
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac80211, remove bitfields from struct ieee80211_if_sta
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use do { } while (0) for multi-line macros
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, CTS protection is partially implemented twice:
 1. via prism2 ioctls, only used by hostapd
 2. via STA beacon parsing, recorded in sta.use_protection but never used
    (other than printed in debugfs)

Protection control should be implemented on a per-subif basis. For example,
a single physical device may be running a soft AP on one channel, and a STA
on another. The AP interface should use protection based on what hostapd told
it, and the STA interface should use protection based on beacon parsing.
These should operate independantly: one subif using protection should not
influence the other.

To implement this, I moved the use_protection flag into ieee80211_sub_if_data
and removed the device-global cts_protect_erp_frames flag.

I also made the PRISM2_PARAM_CTS_PROTECT_ERP_FRAMES write operation only
available for AP interfaces, to avoid any possibility of the user messing with
the behaviour of a STA.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Export various mac80211 internal variables through debugfs.
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>