Replace (tp->speed & LINK_STATUS) with netif_carrier_ok().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set LPM timer to 500us, except for RTL_VER_04 which doesn't link at
USB 3.0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a error occurs when submitting rx, skip the remaining submissions
and try to submit them again next time.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the power on/off recommended procedure for the Single GPHY we
have on our Starfighter 2 switch. In order to make sure we get proper
LED link/activity signaling during suspend, switch the link indication
from the Switch/MAC to the PHY.

Finally, since the GPHY needs to be reset to be put in low power mode,
we will loose any context applied to it: workarounds, EEE etc.. so we
need to call phy_init_hw() to get our fixups re-applied successfully.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the code that touches the single GPHY register from
bcm_sf2_sw_resume() to a separate function since we will have to
enable/disable the GPHY from different locations, and we want the code
to be self-contained.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warning:

vxge-config.c:4640:30: warning: Using plain integer as NULL pointer
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warning:

interface.c:83:5: warning: symbol 'xenvif_poll' was not declared. Should it be static?
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warning:

macb.c:2038:26: warning: symbol 'gem_ethtool_ops' was not declared. Should it be static?

Alongside drops exporting of gem_ethtool_ops as there is no need.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warnings:

bnx2x_main.c:9172:6: warning: symbol 'bnx2x_stop_ptp' was not declared. Should it be static?
bnx2x_main.c:13321:6: warning: symbol 'bnx2x_register_phc' was not declared. Should it be static?
bnx2x_main.c:14638:5: warning: symbol 'bnx2x_enable_ptp_packets' was not declared. Should it be static?
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warnings:

enic_main.c:92:28: warning: symbol 'mod_table' was not declared. Should it be static?
enic_main.c:109:28: warning: symbol 'mod_range' was not declared. Should it be static?
enic_main.c:1306:5: warning: symbol 'enic_busy_poll' was not declared. Should it be static?
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warning:

enic_ethtool.c:95:6: warning: symbol 'enic_intr_coal_set_rx' was not declared. Should it be static?
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warning:

be_cmds.c:2750:5: warning: symbol 'be_cmd_set_qos' was not declared. Should it be static?
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warning:

cxgb4_dcb.c:25:6: warning: symbol 'dcb_ver_array' was not declared. Should it be static?

Alongside making it const.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warnings:

netvsc.c:688:5: warning: symbol 'netvsc_copy_to_send_buf' was not declared. Should it be static?
rndis_filter.c:627:5: warning: symbol 'rndis_filter_set_offload_params' was not declared. Should it be static?
rndis_filter.c:702:5: warning: symbol 'rndis_filter_set_rss_param' was not declared. Should it be static?
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the static attribute groups and the driver data via
tty_port_register_device_attr() instead of manual device_create_file()
and device_remove_file() calls.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows for a VXLAN-GBP socket to talk to a Linux VXLAN socket by
not setting any of the bits.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of manual calls of device_create_file() and
device_remove_files(), assign the static attribute groups to netdev
groups array.  This simplifies the code and avoids the possible
races.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of manual calls of device_create_file() and
device_remove_files(), assign the static attribute groups to netdev
groups array.  This simplifies the code and avoids the possible
races.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions kfree() and vfree() perform also input parameter validation.
Thus the test around their calls is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch fixes following sparse warning:

cpsw-common.c:23:5: warning: symbol 'cpsw_am33xx_cm_get_macid' was not declared. Should it be static?
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After d75b1ade ("net: less interrupt masking in NAPI")
driver's NAPI poll routine is expected to return
exact budget value if it wants to be re-called.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Fixes: d75b1ade ("net: less interrupt masking in NAPI")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cxgb_busy_poll, corresponding to ndo_busy_poll, gets called by the socket
waiting for data.

With busy_poll enabled, improvement is seen in latency numbers as observed by
collecting netperf TCP_RR numbers.
Below are latency number, with and without busy-poll, in a switched environment
for a particular msg size:
netperf command: netperf -4 -H <ip> -l 30 -t TCP_RR -- -r1,1
Latency without busy-poll: ~16.25 us
Latency with busy-poll   : ~08.79 us

Based on original work by Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RSS support requires enablement based on the features reported by
the hardware. The setting of this flag is missing. Add support to
set the RSS enablement flag based on the reported hardware features.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions cpsw_ale_destroy() and of_dev_put() test whether their argument
is NULL and then return immediately. Thus the test around the call
is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The of_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The number of traffic classes reported by the hardware is zero-based
so increment the value returned to get an actual count.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Notify users when TX vlan offload feature changed with ethtool.
Relevant command - ethtool -K <eth> txvlan on/off.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch improves memory utilization and therefore the packets rate
for special MTU's. Instead of setting the frag_stride to the maximal
hard coded frag_size, use the actual frag_size that is set according to
the MTU, when setting the stride of the last frag.
So, for example, for MTU 1600, where the frag_size of the 2nd frag is
86, the frag_size is set to 128 instead of 4096. See below:

Before:
 frag:0 - size:1536 prefix:0 stride:1536
 frag:1 - size:86 prefix:1536 stride:4096

 frag 0 allocator: - size:32768 frags:21
 frag 1 allocator: - size:32768 frags:8

After:
 frag:0 - size:1536 prefix:0 stride:1536
 frag:1 - size:86 prefix:1536 stride:128

 frag 0 allocator: - size:32768 frags:21
 frag 1 allocator: - size:32768 frags:256
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After Initialization of page_alloc, print actual allocated page
size and number of frags it contains. prints is done only when drv
message level is set on the interface.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Align the IDs in the code with the modinfo, lspci -n, etc tools outputs.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We do support cache line sizes of 32 and 64 bytes without activating the
CQE stride feature. Fix a misleading print saying that these cache line
sizes aren't supported.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Initialization to struct config_dev before filling and using it.
Fix to warning:

warning: config_dev.rx_checksum_val may be used uninitialized in this function
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

a) Previously, mlx4_mr_rereg_write filled the MPT's start
   and length with the old MPT's values.
   Fixing the initialization to take the new start and length.

b) In addition access flags in mpt_status were initialized instead of
   status due to bad boolean operation. Fixing the operation.

c) Initialization of pd_slave caused a protection error.
   Fix - removing this initialization.

d) In resource_tracker.c: Fixing vf encoding to be one-based.

Fixes: e630664c ('mlx4_core: Add helper functions to support MR re-registration')
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Capture NETDEV events generated by the bonding driver and based on that
make decisions of how to configure port aggregation in the mlx4 core driver.

This includes setting the V2P port table and re-creating the interested
interfaces in bonded/non-bonded mode.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Supply interface functions to bond and unbond ports of a mlx4 internal
interfaces. Example for such an interface is the one registered by the
mlx4 IB driver under RoCE.

There are

1. Functions to go in/out to/from bonded mode
2. Function to remap virtual ports to physical ports

The bond_mutex prevents simultaneous access to data that keep status of
the device in bonded mode.

The upper mlx4 interface marks to the mlx4 core module that they
want to be subject for such bonding by setting the MLX4_INTFF_BONDING
flag. Interface which goes to/from bonded mode is re-created.

The mlx4 Ethernet driver does not set this flag when registering the
interface, the IB driver does.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>