Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 04 3月, 2015 1 次提交
  3. 03 1月, 2015 1 次提交
    • K
      qmi_wwan: Set random MAC on devices with buggy fw · 531ad428
      由 Kristian Evensen 提交于 
      Some buggy firmwares export an incorrect MAC address (00:a0:c6:00:00:00). This
makes for example checking devices for random MAC addresses tricky, and you
might end up with multiple network interfaces with the same address.

This patch tries to fix, or at least improve, the situation by setting the MAC
address of devices with this firmware bug to a random address. I tested the
patch with two devices that has this firmware bug (Huawei E398 and E392), and
network traffic worked fine after changing the address.
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      531ad428
  5. 17 11月, 2014 1 次提交
  7. 18 7月, 2014 1 次提交
  9. 08 7月, 2014 1 次提交
  11. 07 6月, 2014 1 次提交
  13. 03 6月, 2014 2 次提交
  15. 02 6月, 2014 1 次提交
  17. 28 4月, 2014 7 次提交
  19. 01 4月, 2014 1 次提交
  21. 18 2月, 2014 1 次提交
    • E
      usbnet: remove generic hard_header_len check · eb85569f
      由 Emil Goode 提交于 
      This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.

One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.

With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.

The bug has been reported here:

https://bugzilla.kernel.org/show_bug.cgi?id=29082

This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
  function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
  within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
  callback function that could be affected by this change.
  These extra checks could possibly be removed by someone
  who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
  dev->done list to queue skbs for cleanup.

The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: NEmil Goode <emilgoode@gmail.com>
Reported-by: NIgor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      eb85569f
  23. 14 2月, 2014 1 次提交
  25. 10 2月, 2014 1 次提交
  27. 05 2月, 2014 1 次提交
  29. 05 11月, 2013 2 次提交
  31. 18 10月, 2013 1 次提交
  33. 01 10月, 2013 3 次提交
  35. 12 9月, 2013 1 次提交
    • B
      net: qmi_wwan: add new Qualcomm devices · 0470667c
      由 Bjørn Mork 提交于 
      Adding the device list from the Windows driver description files
included with a new Qualcomm MDM9615 based device, "Alcatel-sbell
ASB TL131 TDD LTE", from China Mobile.  This device is tested
and verified to work.  The others are assumed to work based on
using the same Windows driver.

Many of these devices support multiple QMI/wwan ports, requiring
multiple interface matching entries.  All devices are composite,
providing a mix of one or more serial, storage or Android Debug
Brigde functions in addition to the wwan function.

This device list included an update of one previously known device,
which was incorrectly assumed to have a Gobi 2K layout.  This is
corrected.
Reported-by: N王康 <scateu@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0470667c
  37. 04 9月, 2013 1 次提交
    • J
      drivers/net: Convert uses of compare_ether_addr to ether_addr_equal · 7367d0b5
      由 Joe Perches 提交于 
      Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script: (and a little typing)

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7367d0b5
  39. 02 7月, 2013 4 次提交
  41. 24 6月, 2013 1 次提交
  43. 11 6月, 2013 1 次提交
    • B
      qmi_wwan/cdc_ether: let qmi_wwan handle the Huawei E1820 · c2020be3
      由 Bjørn Mork 提交于 
      Another QMI speaking Qualcomm based device, which should be
driven by qmi_wwan, while cdc_ether should ignore it.

Like on other Huawei devices, the wwan function can appear
either as a single vendor specific interface or as a CDC ECM
class function using separate control and data interfaces.
The ECM control interface protocol is 0xff, likely in an
attempt to indicate that vendor specific management is
required.

In addition to the near standard CDC class, Huawei also add
vendor specific AT management commands to their firmwares.
This is probably an attempt to support non-Windows systems
using standard class drivers.  Unfortunately, this part of
the firmware is often buggy.  Linux is much better off using
whatever native vendor specific management protocol the
device offers, and Windows uses, whenever possible. This
means QMI in the case of Qualcomm based devices.

The E1820 has been verified to work fine with QMI.

Matching on interface number is necessary to distiguish the
wwan function from serial functions in the single interface
mode, as both function types will have class/subclass/function
set to ff/ff/ff.

The control interface number does not change in CDC ECM mode,
so the interface number matching rule is sufficient to handle
both modes.  The cdc_ether blacklist entry is only relevant in
CDC ECM mode, but using a similar interface number based rule
helps document this as a transfer from one driver to another.

Other Huawei 02/06/ff devices are left with the cdc_ether driver
because we do not know whether they are based on Qualcomm chips.
The Huawei specific AT command management is known to be somewhat
hardware independent, and their usage of these class codes may
also be independent of the modem hardware.
Reported-by: NGraham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c2020be3
  45. 23 5月, 2013 1 次提交
  47. 09 5月, 2013 1 次提交
  49. 04 5月, 2013 1 次提交
  51. 20 4月, 2013 2 次提交
    • B
      net: qmi_wwan: prevent duplicate mac address on link (firmware bug workaround) · cc6ba5fd
      由 Bjørn Mork 提交于 
      We normally trust and use the CDC functional descriptors provided by a
number of devices.  But some of these will erroneously list the address
reserved for the device end of the link.  Attempting to use this on
both the device and host side will naturally not work.

Work around this bug by ignoring the functional descriptor and assign a
random address instead in this case.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      cc6ba5fd
    • B
      net: qmi_wwan: fixup destination address (firmware bug workaround) · 6483bdc9
      由 Bjørn Mork 提交于 
      Received packets are sometimes addressed to 00:a0:c6:00:00:00
instead of the address the device firmware should have learned
from the host:

321.224126 77.16.85.204 -> 148.122.171.134 ICMP 98 Echo (ping) request  id=0x4025, seq=64/16384, ttl=64

0000  82 c0 82 c9 f1 67 82 c0 82 c9 f1 67 08 00 45 00   .....g.....g..E.
0010  00 54 00 00 40 00 40 01 57 cc 4d 10 55 cc 94 7a   .T..@.@.W.M.U..z
0020  ab 86 08 00 62 fc 40 25 00 40 b2 bc 6e 51 00 00   ....b.@%.@..nQ..
0030  00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15   ..k.............
0040  16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25   .......... !"#$%
0050  26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35   &'()*+,-./012345
0060  36 37                                             67

321.240607 148.122.171.134 -> 77.16.85.204 ICMP 98 Echo (ping) reply    id=0x4025, seq=64/16384, ttl=55

0000  00 a0 c6 00 00 00 02 50 f3 00 00 00 08 00 45 00   .......P......E.
0010  00 54 00 56 00 00 37 01 a0 76 94 7a ab 86 4d 10   .T.V..7..v.z..M.
0020  55 cc 00 00 6a fc 40 25 00 40 b2 bc 6e 51 00 00   U...j.@%.@..nQ..
0030  00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15   ..k.............
0040  16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25   .......... !"#$%
0050  26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35   &'()*+,-./012345
0060  36 37                                             67

The bogus address is always the same, and matches the address
suggested by many devices as a default address.  It is likely a
hardcoded firmware default.

The circumstances where this bug has been observed indicates that
the trigger is related to timing or some other factor the host
cannot control. Repeating the exact same configuration sequence
that caused it to trigger once, will not necessarily cause it to
trigger the next time. Reproducing the bug is therefore difficult.
This opens up a possibility that the bug is more common than we can
confirm, because affected devices often will work properly again
after a reset.  A procedure most users are likely to try out before
reporting a bug.

Unconditionally rewriting the destination address if the first digit
of the received packet is 0, is considered an acceptable compromise
since we already have to inspect this digit.  The simplification will
cause unnecessary rewrites if the real address starts with 0, but this
is still better than adding additional tests for this particular case.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6483bdc9