We hit ftrace_bug report when booting Android on a 64bit ATOM SOC chip.
Basically, there is a race between insmod and ftrace_run_update_code.

After load_module=>ftrace_module_init, another thread jumps in to call
ftrace_run_update_code=>ftrace_arch_code_modify_prepare
                        =>set_all_modules_text_rw, to change all modules
as RW. Since the new module is at MODULE_STATE_UNFORMED, the text attribute
is not changed. Then, the 2nd thread goes ahead to change codes.
However, load_module continues to call complete_formation=>set_section_ro_nx,
then 2nd thread would fail when probing the module's TEXT.

The patch fixes it by using notifier to delay the enabling of ftrace
records to the time when module is at state MODULE_STATE_COMING.

Link: http://lkml.kernel.org/r/567CE628.3000609@intel.comSigned-off-by: NQiu Peiyang <peiyangx.qiu@intel.com>
Signed-off-by: NZhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Qiu Peiyang pointed out that there's a race when enabling function tracing
and loading a module. In order to make the modifications of converting nops
in the prologue of functions into callbacks, the text needs to be converted
from read-only to read-write. When enabling function tracing, the text
permission is updated, the functions are modified, and then they are put
back.

When loading a module, the updates to convert function calls to mcount is
done before the module text is set to read-only. But after it is done, the
module text is visible by the function tracer. Thus we have the following
race:

	CPU 0			CPU 1
	-----			-----
   start function tracing
   set text to read-write
			     load_module
			     add functions to ftrace
			     set module text read-only

   update all functions to callbacks
   modify module functions too
   < Can't it's read-only >

When this happens, ftrace detects the issue and disables itself till the
next reboot.

To fix this, a new DISABLED flag is added for ftrace records, which all
module functions get when they are added. Then later, after the module code
is all set, the records will have the DISABLED flag cleared, and they will
be enabled if any callback wants all functions to be traced.

Note, this doesn't add the delay to later. It simply changes the
ftrace_module_init() to do both the setting of DISABLED records, and then
immediately calls the enable code. This helps with testing this new code as
it has the same behavior as previously. Another change will come after this
to have the ftrace_module_enable() called after the text is set to
read-only.

Cc: Qiu Peiyang <peiyangx.qiu@intel.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.

Link: http://lkml.kernel.org/r/1449367378-29430-6-git-send-email-huawei.libin@huawei.comReviewed-by: NThomas Gleixner <tglx@linutronix.de>
Suggested-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NLi Bin <huawei.libin@huawei.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

The file tracing_enable is obsolete and does not exist anymore. Replace
the comment that references it with the proper tracing_on file.

Link: http://lkml.kernel.org/r/1450787141-45544-1-git-send-email-chuhu@redhat.comSigned-off-by: NChuyu Hu <chuhu@redhat.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.

Link: http://lkml.kernel.org/r/1449367378-29430-3-git-send-email-huawei.libin@huawei.com

Cc: linux-metag@vger.kernel.org
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Suggested-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NLi Bin <huawei.libin@huawei.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.

Link: http://lkml.kernel.org/r/1449367378-29430-5-git-send-email-huawei.libin@huawei.com

Cc: linux-sh@vger.kernel.org
Suggested-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NLi Bin <huawei.libin@huawei.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.

Link: http://lkml.kernel.org/r/1449214067-12177-2-git-send-email-huawei.libin@huawei.com

Cc: linux-ia64@vger.kernel.org
Acked-by: NTony Luck <tony.luck@intel.com>
Suggested-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NLi Bin <huawei.libin@huawei.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

The start and end variables were only used when ftrace_module_init() was
split up into multiple functions. No need to keep them around after the
merger.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Simple cleanup. No need for two functions here.
The whole work can simply be done inside 'ftrace_module_init'.

Link: http://lkml.kernel.org/r/1449067197-5718-1-git-send-email-abelvesa@linux.comSigned-off-by: NAbel Vesa <abelvesa@linux.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

TRACE_EVENT_FN can't be used in some circumstances
like invoking trace functions from offlined CPU due
to RCU usage.

This patch adds the TRACE_EVENT_FN_COND macro
to make such trace points conditional.

Link: http://lkml.kernel.org/r/1450124286-4822-1-git-send-email-kda@linux-powerpc.orgSigned-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

commit 5ac48378 ("tracing: Use trace_seq_used() and seq_buf_used()
instead of len") changed the tracing code to use trace_seq_used() and
seq_buf_used() instead of using the seq_buf len directly to avoid
overflow issues, but missed a spot in seq_buf_to_user() that makes use
of s->len.

Cleaned up the code a bit as well per suggestion of Steve Rostedt.

Link: http://lkml.kernel.org/r/1447703848-2951-1-git-send-email-jsnitsel@redhat.comSigned-off-by: NJerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

This bpf_verifier_ops structure is never modified, like the other
bpf_verifier_ops structures, so declare it as const.

Done with the help of Coccinelle.

Link: http://lkml.kernel.org/r/1449855359-13724-1-git-send-email-Julia.Lawall@lip6.frSigned-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Jiri Olsa noted that the change to replace the control_ops did not update
the trampoline for when running perf on a single CPU and with CONFIG_PREEMPT
disabled (where dynamic ops, like perf, can use trampolines directly). The
result was that perf function could be called when RCU is not watching as
well as not handle the ftrace_local_disable().

Modify the ftrace_ops_get_func() to also check the RCU and PER_CPU ops flags
and use the recursive function if they are set. The recursive function is
modified to check those flags and execute the appropriate checks if they are
set.

Link: http://lkml.kernel.org/r/20151201134213.GA14155@krava.brq.redhat.comReported-by: NJiri Olsa <jolsa@redhat.com>
Patch-fixed-up-by: NJiri Olsa <jolsa@redhat.com>
Tested-by: NJiri Olsa <jolsa@kernel.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Currently perf has its own list function within the ftrace infrastructure
that seems to be used only to allow for it to have per-cpu disabling as well
as a check to make sure that it's not called while RCU is not watching. It
uses something called the "control_ops" which is used to iterate over ops
under it with the control_list_func().

The problem is that this control_ops and control_list_func unnecessarily
complicates the code. By replacing FTRACE_OPS_FL_CONTROL with two new flags
(FTRACE_OPS_FL_RCU and FTRACE_OPS_FL_PER_CPU) we can remove all the code
that is special with the control ops and add the needed checks within the
generic ftrace_list_func().
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When showing all tramps registered to a ftrace record in the file
enabled_functions, it exits the loop with ops == NULL. But then it is
suppose to show the function on the ops->trampoline and
add_trampoline_func() is called with the given ops. But because ops is now
NULL (to exit the loop), it always shows the static trampoline instead of
the one that is really registered to the record.

The call to add_trampoline_func() that shows the trampoline for the given
ops needs to be called at every iteration.

Fixes: 39daa7b9 "ftrace: Show all tramps registered to a record on ftrace_bug()"
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

s/ARCH_SUPPORT_FTARCE_OPS/ARCH_SUPPORTS_FTRACE_OPS/

Link: http://lkml.kernel.org/r/1448879016-8659-1-git-send-email-huawei.libin@huawei.comSigned-off-by: NLi Bin <huawei.libin@huawei.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When an anomaly is detected in the function call modification code,
ftrace_bug() is called to disable function tracing as well as give any
information that may help debug the problem. Currently, only the first found
trampoline that is attached to the failed record is reported. Instead, show
all trampolines that are hooked to it.

Also, not only show the ops pointer but also report the function it calls.

While at it, add this info to the enabled_functions debug file too.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When an anomaly is found while modifying function code, ftrace_bug() is
called which disables the function tracing infrastructure and reports
information about what failed. If the code that is to be replaced does not
match what is expected, then actual code is shown. Currently there is no
arch generic way to show what was expected.

Add a new variable pointer calld ftrace_expected that the arch code can set
to point to what it expected so that ftrace_bug() can report the actual text
as well as the text that was expected to be there.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

The ftrace function hook utility has several internal checks to make sure
that whatever it modifies is exactly what it expects to be modifying. This
is essential as modifying running code can be extremely dangerous to the
system.

When an anomaly is detected, ftrace_bug() is called which sends a splat to
the console and disables function tracing. There's some extra information
that is printed to help diagnose the issue.

One thing that is missing though is output of what ftrace was doing at the
time of the crash. Was it updating a call site or perhaps converting a call
site to a nop? A new global enum variable is created to state what ftrace
was doing at the time of the anomaly, and this is reported in ftrace_bug().
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When a trigger is enabled, the cond flag should be set beforehand,
otherwise a trigger that's expecting to process a trace record
(e.g. one with post_trigger set) could be invoked without one.

Likewise a trigger's cond flag should be reset after it's disabled,
not before.

Link: http://lkml.kernel.org/r/a420b52a67b1c2d3cab017914362d153255acb99.1448303214.git.tom.zanussi@linux.intel.comSigned-off-by: NTom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Reviewed-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Reviewed-by: NNamhyung Kim <namhyung@kernel.org>
Tested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When crossing over to a new page, commit the current work. This will allow
readers to get data with less latency, and also simplifies the work to get
timestamps working for interrupted events.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

The first commit of a buffer page updates the timestamp of that page. No
need to have the update to the next page add the timestamp too. It will only
be replaced by the first commit on that page anyway.

Only update to a page if it contains an event.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

As cpu_buffer->tail_page may be modified by interrupts at almost any time,
the flow of logic is very important. Do not let gcc get smart with
re-reading cpu_buffer->tail_page by adding READ_ONCE() around most of its
accesses.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Create a test to test instance creation and deletion. Several tasks are
created that create 3 directories and delete them. The tasks all create the
same directories. This places a stress on the code that creates and deletes
instances.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Commit fcc742ea "ring-buffer: Add event descriptor to simplify passing
data" added a descriptor that holds various data instead of passing around
several variables through parameters. The problem was that one of the
parameters was modified in a function and the code was designed not to have
an effect on that modified  parameter. Now that the parameter is a
descriptor and any modifications to it are non-volatile, the size of the
data could be unnecessarily expanded.

Remove the extra space added if a timestamp was added and the event went
across the page.

Cc: stable@vger.kernel.org # 4.3+
Fixes: fcc742ea "ring-buffer: Add event descriptor to simplify passing data"
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Do not update the read stamp after swapping out the reader page from the
write buffer. If the reader page is swapped out of the buffer before an
event is written to it, then the read_stamp may get an out of date
timestamp, as the page timestamp is updated on the first commit to that
page.

rb_get_reader_page() only returns a page if it has an event on it, otherwise
it will return NULL. At that point, check if the page being returned has
events and has not been read yet. Then at that point update the read_stamp
to match the time stamp of the reader page.

Cc: stable@vger.kernel.org # 2.6.30+
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Merge slub bulk allocator updates from Andrew Morton:
 "This missed the merge window because I was waiting for some repairs to
  come in.  Nothing actually uses the bulk allocator yet and the changes
  to other code paths are pretty small.  And the net guys are waiting
  for this so they can start merging the client code"

More comments from Jesper Dangaard Brouer:
 "The kmem_cache_alloc_bulk() call, in mm/slub.c, were included in
  previous kernel.  The present version contains a bug.  Vladimir
  Davydov noticed it contained a bug, when kernel is compiled with
  CONFIG_MEMCG_KMEM (see commit 03ec0ed5: "slub: fix kmem cgroup
  bug in kmem_cache_alloc_bulk").  Plus the mem cgroup counterpart in
  kmem_cache_free_bulk() were missing (see commit 03374518 "slub:
  add missing kmem cgroup support to kmem_cache_free_bulk").

  I don't consider the fix stable-material because there are no in-tree
  users of the API.

  But with known bugs (for memcg) I cannot start using the API in the
  net-tree"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  slab/slub: adjust kmem_cache_alloc_bulk API
  slub: add missing kmem cgroup support to kmem_cache_free_bulk
  slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
  slub: optimize bulk slowpath free by detached freelist
  slub: support for bulk free with SLUB freelists

Pull tty/serial fixes from Greg KH:
 "Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
  some reported problems.

  All have been in linux-next, full details are in the shortlog below"

* tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: export fsl8250_handle_irq
  serial: 8250_mid: Add missing dependency
  tty: audit: Fix audit source
  serial: etraxfs-uart: Fix crash
  serial: fsl_lpuart: Fix earlycon support
  bcm63xx_uart: Use the device name when registering an interrupt
  tty: Fix direct use of tty buffer work
  tty: Fix tty_send_xchar() lock order inversion

Pull staging/IIO fixes from Greg KH:
 "Here are some staging and iio driver fixes for 4.4-rc2.  All of these
  are in response to issues that have been reported and have been in
  linux-next for a while"

* tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"
  iio: adc: xilinx: Fix VREFN scale
  iio: si7020: Swap data byte order
  iio: adc: vf610_adc: Fix division by zero error
  iio:ad7793: Fix ad7785 product ID
  iio: ad5064: Fix ad5629/ad5669 shift
  iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success
  iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock
  staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN
  vf610_adc: Fix internal temperature calculation

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes and new device ids for 4.4-rc2.  All
  have been in linux-next and the details are in the shortlog"

* tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
  usblp: do not set TASK_INTERRUPTIBLE before lock
  USB: MAINTAINERS: cxacru
  usb: kconfig: fix warning of select USB_OTG
  USB: option: add XS Stick W100-2 from 4G Systems
  xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devices
  usb: xhci: fix checking ep busy for CFC
  xhci: Workaround to get Intel xHCI reset working more reliably
  usb: chipidea: imx: fix a possible NULL dereference
  usb: chipidea: usbmisc_imx: fix a possible NULL dereference
  usb: chipidea: otg: gadget module load and unload support
  usb: chipidea: debug: disable usb irq while role switch
  ARM: dts: imx27.dtsi: change the clock information for usb
  usb: chipidea: imx: refine clock operations to adapt for all platforms
  usb: gadget: atmel_usba_udc: Expose correct device speed
  usb: musb: enable usb_dma parameter
  usb: phy: phy-mxs-usb: fix a possible NULL dereference
  usb: dwc3: gadget: let us set lower max_speed
  usb: musb: fix tx fifo flush handling
  usb: gadget: f_loopback: fix the warning during the enumeration
  usb: dwc2: host: Fix remote wakeup when not in DWC2_L2
  ...

Pull MIPS fixes from Ralf Baechle:

 - Fix a flood of annoying build warnings

 - A number of fixes for Atheros 79xx platforms

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ath79: Add a machine entry for booting OF machines
  MIPS: ath79: Fix the size of the MISC INTC registers in ar9132.dtsi
  MIPS: ath79: Fix the DDR control initialization on ar71xx and ar934x
  MIPS: Fix flood of warnings about comparsion being always true.

Pull parisc update from Helge Deller:
 "This patchset adds Huge Page and HUGETLBFS support for parisc"

Honestly, the hugepage support should have gone through in the merge
window, and is not really an rc-time fix.  But it only touches
arch/parisc, and I cannot find it in myself to care.  If one of the
three parisc users notices a breakage, I will point at Helge and make
rude farting noises.

* 'parisc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Map kernel text and data on huge pages
  parisc: Add Huge Page and HUGETLBFS support
  parisc: Use long branch to do_syscall_trace_exit
  parisc: Increase initial kernel mapping to 32MB on 64bit kernel
  parisc: Initialize the fault vector earlier in the boot process.
  parisc: Add defines for Huge page support
  parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
  parisc: Drop definition of start_thread_som for HP-UX SOM binaries
  parisc: Fix wrong comment regarding first pmd entry flags

Pull perf tool fixes from Thomas Gleixner:
 "A couple of fixes for perf tools:

   - Build system updates

   - Plug a memory leak in an error path of perf probe

   - Tear down probes correctly when adding fails

   - Fixes to the perf symbol handling

   - Fix ordering of event processing in buildid-list

   - Fix per DSO filtering in the histogram browser"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf probe: Clear probe_trace_event when add_probe_trace_event() fails
  perf probe: Fix memory leaking on failure by clearing all probe_trace_events
  perf inject: Also re-pipe lost_samples event
  perf buildid-list: Requires ordered events
  perf symbols: Fix dso lookup by long name and missing buildids
  perf symbols: Allow forcing reading of non-root owned files by root
  perf hists browser: The dso can be obtained from popup_action->ms.map->dso
  perf hists browser: Fix 'd' hotkey action to filter by DSO
  perf symbols: Rebuild rbtree when adjusting symbols for kcore
  tools: Add a "make all" rule
  tools: Actually install tmon in the install rule

Pull x86 fixes from Thomas Gleixner:
 "This update contains:

   - MPX updates for handling 32bit processes

   - A fix for a long standing bug in 32bit signal frame handling
     related to FPU/XSAVE state

   - Handle get_xsave_addr() correctly in KVM

   - Fix SMAP check under paravirtualization

   - Add a comment to the static function trace entry to avoid further
     confusion about the difference to dynamic tracing"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Fix SMAP check in PVOPS environments
  x86/ftrace: Add comment on static function tracing
  x86/fpu: Fix get_xsave_addr() behavior under virtualization
  x86/fpu: Fix 32-bit signal frame handling
  x86/mpx: Fix 32-bit address space calculation
  x86/mpx: Do proper get_user() when running 32-bit binaries on 64-bit kernels

Adjust kmem_cache_alloc_bulk API before we have any real users.

Adjust API to return type 'int' instead of previously type 'bool'.  This
is done to allow future extension of the bulk alloc API.

A future extension could be to allow SLUB to stop at a page boundary, when
specified by a flag, and then return the number of objects.

The advantage of this approach, would make it easier to make bulk alloc
run without local IRQs disabled.  With an approach of cmpxchg "stealing"
the entire c->freelist or page->freelist.  To avoid overshooting we would
stop processing at a slab-page boundary.  Else we always end up returning
some objects at the cost of another cmpxchg.

To keep compatible with future users of this API linking against an older
kernel when using the new flag, we need to return the number of allocated
objects with this API change.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: NChristoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Initial implementation missed support for kmem cgroup support in
kmem_cache_free_bulk() call, add this.

If CONFIG_MEMCG_KMEM is not enabled, the compiler should be smart enough
to not add any asm code.

Incoming bulk free objects can belong to different kmem cgroups, and
object free call can happen at a later point outside memcg context.  Thus,
we need to keep the orig kmem_cache, to correctly verify if a memcg object
match against its "root_cache" (s->memcg_params.root_cache).
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: NVladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The call slab_pre_alloc_hook() interacts with kmemgc and is not allowed to
be called several times inside the bulk alloc for loop, due to the call to
memcg_kmem_get_cache().

This would result in hitting the VM_BUG_ON in __memcg_kmem_get_cache.

As suggested by Vladimir Davydov, change slab_post_alloc_hook() to be able
to handle an array of objects.

A subtle detail is, loop iterator "i" in slab_post_alloc_hook() must have
same type (size_t) as size argument.  This helps the compiler to easier
realize that it can remove the loop, when all debug statements inside loop
evaluates to nothing.  Note, this is only an issue because the kernel is
compiled with GCC option: -fno-strict-overflow

In slab_alloc_node() the compiler inlines and optimizes the invocation of
slab_post_alloc_hook(s, flags, 1, &object) by removing the loop and access
object directly.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reported-by: NVladimir Davydov <vdavydov@virtuozzo.com>
Suggested-by: NVladimir Davydov <vdavydov@virtuozzo.com>
Reviewed-by: NVladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This change focus on improving the speed of object freeing in the
"slowpath" of kmem_cache_free_bulk.

The calls slab_free (fastpath) and __slab_free (slowpath) have been
extended with support for bulk free, which amortize the overhead of
the (locked) cmpxchg_double.

To use the new bulking feature, we build what I call a detached
freelist.  The detached freelist takes advantage of three properties:

 1) the free function call owns the object that is about to be freed,
    thus writing into this memory is synchronization-free.

 2) many freelist's can co-exist side-by-side in the same slab-page
    each with a separate head pointer.

 3) it is the visibility of the head pointer that needs synchronization.

Given these properties, the brilliant part is that the detached
freelist can be constructed without any need for synchronization.  The
freelist is constructed directly in the page objects, without any
synchronization needed.  The detached freelist is allocated on the
stack of the function call kmem_cache_free_bulk.  Thus, the freelist
head pointer is not visible to other CPUs.

All objects in a SLUB freelist must belong to the same slab-page.
Thus, constructing the detached freelist is about matching objects
that belong to the same slab-page.  The bulk free array is scanned is
a progressive manor with a limited look-ahead facility.

Kmem debug support is handled in call of slab_free().

Notice kmem_cache_free_bulk no longer need to disable IRQs. This
only slowed down single free bulk with approx 3 cycles.

Performance data:
 Benchmarked[1] obj size 256 bytes on CPU i7-4790K @ 4.00GHz

SLUB fastpath single object quick reuse: 47 cycles(tsc) 11.931 ns

To get stable and comparable numbers, the kernel have been booted with
"slab_merge" (this also improve performance for larger bulk sizes).

Performance data, compared against fallback bulking:

bulk -  fallback bulk            - improvement with this patch
   1 -  62 cycles(tsc) 15.662 ns - 49 cycles(tsc) 12.407 ns- improved 21.0%
   2 -  55 cycles(tsc) 13.935 ns - 30 cycles(tsc) 7.506 ns - improved 45.5%
   3 -  53 cycles(tsc) 13.341 ns - 23 cycles(tsc) 5.865 ns - improved 56.6%
   4 -  52 cycles(tsc) 13.081 ns - 20 cycles(tsc) 5.048 ns - improved 61.5%
   8 -  50 cycles(tsc) 12.627 ns - 18 cycles(tsc) 4.659 ns - improved 64.0%
  16 -  49 cycles(tsc) 12.412 ns - 17 cycles(tsc) 4.495 ns - improved 65.3%
  30 -  49 cycles(tsc) 12.484 ns - 18 cycles(tsc) 4.533 ns - improved 63.3%
  32 -  50 cycles(tsc) 12.627 ns - 18 cycles(tsc) 4.707 ns - improved 64.0%
  34 -  96 cycles(tsc) 24.243 ns - 23 cycles(tsc) 5.976 ns - improved 76.0%
  48 -  83 cycles(tsc) 20.818 ns - 21 cycles(tsc) 5.329 ns - improved 74.7%
  64 -  74 cycles(tsc) 18.700 ns - 20 cycles(tsc) 5.127 ns - improved 73.0%
 128 -  90 cycles(tsc) 22.734 ns - 27 cycles(tsc) 6.833 ns - improved 70.0%
 158 -  99 cycles(tsc) 24.776 ns - 30 cycles(tsc) 7.583 ns - improved 69.7%
 250 - 104 cycles(tsc) 26.089 ns - 37 cycles(tsc) 9.280 ns - improved 64.4%

Performance data, compared current in-kernel bulking:

bulk - curr in-kernel  - improvement with this patch
   1 -  46 cycles(tsc) - 49 cycles(tsc) - improved (cycles:-3) -6.5%
   2 -  27 cycles(tsc) - 30 cycles(tsc) - improved (cycles:-3) -11.1%
   3 -  21 cycles(tsc) - 23 cycles(tsc) - improved (cycles:-2) -9.5%
   4 -  18 cycles(tsc) - 20 cycles(tsc) - improved (cycles:-2) -11.1%
   8 -  17 cycles(tsc) - 18 cycles(tsc) - improved (cycles:-1) -5.9%
  16 -  18 cycles(tsc) - 17 cycles(tsc) - improved (cycles: 1)  5.6%
  30 -  18 cycles(tsc) - 18 cycles(tsc) - improved (cycles: 0)  0.0%
  32 -  18 cycles(tsc) - 18 cycles(tsc) - improved (cycles: 0)  0.0%
  34 -  78 cycles(tsc) - 23 cycles(tsc) - improved (cycles:55) 70.5%
  48 -  60 cycles(tsc) - 21 cycles(tsc) - improved (cycles:39) 65.0%
  64 -  49 cycles(tsc) - 20 cycles(tsc) - improved (cycles:29) 59.2%
 128 -  69 cycles(tsc) - 27 cycles(tsc) - improved (cycles:42) 60.9%
 158 -  79 cycles(tsc) - 30 cycles(tsc) - improved (cycles:49) 62.0%
 250 -  86 cycles(tsc) - 37 cycles(tsc) - improved (cycles:49) 57.0%

Performance with normal SLUB merging is significantly slower for
larger bulking.  This is believed to (primarily) be an effect of not
having to share the per-CPU data-structures, as tuning per-CPU size
can achieve similar performance.

bulk - slab_nomerge   -  normal SLUB merge
   1 -  49 cycles(tsc) - 49 cycles(tsc) - merge slower with cycles:0
   2 -  30 cycles(tsc) - 30 cycles(tsc) - merge slower with cycles:0
   3 -  23 cycles(tsc) - 23 cycles(tsc) - merge slower with cycles:0
   4 -  20 cycles(tsc) - 20 cycles(tsc) - merge slower with cycles:0
   8 -  18 cycles(tsc) - 18 cycles(tsc) - merge slower with cycles:0
  16 -  17 cycles(tsc) - 17 cycles(tsc) - merge slower with cycles:0
  30 -  18 cycles(tsc) - 23 cycles(tsc) - merge slower with cycles:5
  32 -  18 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:4
  34 -  23 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:-1
  48 -  21 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:1
  64 -  20 cycles(tsc) - 48 cycles(tsc) - merge slower with cycles:28
 128 -  27 cycles(tsc) - 57 cycles(tsc) - merge slower with cycles:30
 158 -  30 cycles(tsc) - 59 cycles(tsc) - merge slower with cycles:29
 250 -  37 cycles(tsc) - 56 cycles(tsc) - merge slower with cycles:19

Joint work with Alexander Duyck.

[1] https://github.com/netoptimizer/prototype-kernel/blob/master/kernel/mm/slab_bulk_test01.c

[akpm@linux-foundation.org: BUG_ON -> WARN_ON;return]
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: NChristoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make it possible to free a freelist with several objects by adjusting API
of slab_free() and __slab_free() to have head, tail and an objects counter
(cnt).

Tail being NULL indicate single object free of head object.  This allow
compiler inline constant propagation in slab_free() and
slab_free_freelist_hook() to avoid adding any overhead in case of single
object free.

This allows a freelist with several objects (all within the same
slab-page) to be free'ed using a single locked cmpxchg_double in
__slab_free() and with an unlocked cmpxchg_double in slab_free().

Object debugging on the free path is also extended to handle these
freelists.  When CONFIG_SLUB_DEBUG is enabled it will also detect if
objects don't belong to the same slab-page.

These changes are needed for the next patch to bulk free the detached
freelists it introduces and constructs.

Micro benchmarking showed no performance reduction due to this change,
when debugging is turned off (compiled with CONFIG_SLUB_DEBUG).
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: NChristoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>