Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 03 6月, 2009 2 次提交
  3. 02 6月, 2009 1 次提交
    • N
      ipv4: New multicast-all socket option · f771bef9
      由 Nivedita Singhvi 提交于 
      After some discussion offline with Christoph Lameter and David Stevens
regarding multicast behaviour in Linux, I'm submitting a slightly
modified patch from the one Christoph submitted earlier.

This patch provides a new socket option IP_MULTICAST_ALL.

In this case, default behaviour is _unchanged_ from the current
Linux standard. The socket option is set by default to provide
original behaviour. Sockets wishing to receive data only from
multicast groups they join explicitly will need to clear this
socket option.
Signed-off-by: NNivedita Singhvi <niv@us.ibm.com>
Signed-off-by: Christoph Lameter<cl@linux.com>
Acked-by: NDavid Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f771bef9
  5. 01 6月, 2009 2 次提交
  7. 30 5月, 2009 1 次提交
    • J
      net: convert unicast addr list · ccffad25
      由 Jiri Pirko 提交于 
      This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).

I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.

The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>

 drivers/net/bnx2.c               |   13 +--
 drivers/net/e1000/e1000_main.c   |   24 +++--
 drivers/net/ixgbe/ixgbe_common.c |   14 ++--
 drivers/net/ixgbe/ixgbe_common.h |    4 +-
 drivers/net/ixgbe/ixgbe_main.c   |    6 +-
 drivers/net/ixgbe/ixgbe_type.h   |    4 +-
 drivers/net/macvlan.c            |   11 +-
 drivers/net/mv643xx_eth.c        |   11 +-
 drivers/net/niu.c                |    7 +-
 drivers/net/virtio_net.c         |    7 +-
 drivers/s390/net/qeth_l2_main.c  |    6 +-
 drivers/scsi/fcoe/fcoe.c         |   16 ++--
 include/linux/netdevice.h        |   18 ++--
 net/8021q/vlan.c                 |    4 +-
 net/8021q/vlan_dev.c             |   10 +-
 net/core/dev.c                   |  195 +++++++++++++++++++++++++++-----------
 net/dsa/slave.c                  |   10 +-
 net/packet/af_packet.c           |    4 +-
 18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ccffad25
  9. 29 5月, 2009 3 次提交
    • J
      bonding: allow bond in mode balance-alb to work properly in bridge -try4.3 · 5d4e039b
      由 Jiri Pirko 提交于 
      [PATCH net-next] bonding: allow bond in mode balance-alb to work properly in bridge -try4.3

(updated)
changes v4.2 -> v4.3
- memcpy the address always, not just in case it differs from master->dev_addr
- compare_ether_addr_64bits() is not used so there is no direct need to make new
  header file (I think it would be good to have bond stuff in separate file
  anyway).

changes v4.1 -> v4.2
- use skb->pkt_type == PACKET_HOST compare rather then comparing skb dest addr
  against skb->dev->dev_addr

The problem is described in following bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=487763

Basically here's what's going on. In every mode, bonding interface uses the same
mac address for all enslaved devices (except fail_over_mac). Only balance-alb
will simultaneously use multiple MAC addresses across different slaves. When you
put this kind of bond device into a bridge it will only add one of mac adresses
into a hash list of mac addresses, say X. This mac address is marked as local.
But this bonding interface also has mac address Y. Now then packet arrives with
destination address Y, this address is not marked as local and the packed looks
like it needs to be forwarded. This packet is then lost which is wrong.

Notice that interfaces can be added and removed from bond while it is in bridge.

***
When the multiple addresses for bridge port approach failed to solve this issue
due to STP I started to think other way to solve this. I returned to previous
solution but tweaked one.

This patch solves the situation in the bonding without touching bridge code.
For every incoming frame to bonding the destination address is compared to
current address of the slave device from which tha packet came. If these two
match destination address is replaced by mac address of the master. This address
is known by bridge so it is delivered properly. Note that the comparsion is not
made directly, it's used skb->pkt_type == PACKET_HOST instead. This is "set"
previously in eth_type_trans().

I experimentally tried that this works as good as searching through the slave
list (v4 of this patch).

Jirka
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5d4e039b
    • I
      wimax: a new API call was added, increment minor protocol version number · 7481806d
      由 Inaky Perez-Gonzalez 提交于 
      As the 'state_get' API call was added, we need to increase the minor
protocol version number so applications that depend on the can check
it's presence.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
      7481806d
    • P
      wimax: Add netlink interface to get device state · 7f0333eb
      由 Paulius Zaleckas 提交于 
      wimax connection manager / daemon has to know what is current
state of the device. Previously it was only possible to get
notification whet state has changed.

Note:

 By mistake, the new generic netlink's number for
 WIMAX_GNL_OP_STATE_GET was declared inserting into the existing list
 of API calls, not appending; thus, it'd break existing API.

 Fixed by Inaky Perez-Gonzalez <inaky@linux.intel.com> by moving to
 the tail, where we add to the interface, not modify the interface.

 Thanks to Stephen Hemminger <shemminger@vyatta.com> for catching this.
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
      7f0333eb
  11. 28 5月, 2009 2 次提交
  13. 27 5月, 2009 5 次提交
  15. 26 5月, 2009 1 次提交
    • E
      net: txq_trans_update() helper · 08baf561
      由 Eric Dumazet 提交于 
      We would like to get rid of netdev->trans_start = jiffies; that about all net
drivers have to use in their start_xmit() function, and use txq->trans_start
instead.

This can be done generically in core network, as suggested by David.

Some devices, (particularly loopback) dont need trans_start update, because
they dont have transmit watchdog. We could add a new device flag, or rely
on fact that txq->tran_start can be updated is txq->xmit_lock_owner is
different than -1. Use a helper function to hide our choice.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      08baf561
  17. 25 5月, 2009 9 次提交
  19. 23 5月, 2009 1 次提交
  21. 22 5月, 2009 2 次提交
    • N
      dropmon: add ability to detect when hardware dropsrxpackets · 4ea7e386
      由 Neil Horman 提交于 
      Patch to add the ability to detect drops in hardware interfaces via dropwatch.
Adds a tracepoint to net_rx_action to signal everytime a napi instance is
polled.  The dropmon code then periodically checks to see if the rx_frames
counter has changed, and if so, adds a drop notification to the netlink
protocol, using the reserved all-0's vector to indicate the drop location was in
hardware, rather than somewhere in the code.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>

 include/linux/net_dropmon.h |    8 ++
 include/trace/napi.h        |   11 +++
 net/core/dev.c              |    5 +
 net/core/drop_monitor.c     |  124 ++++++++++++++++++++++++++++++++++++++++++--
 net/core/net-traces.c       |    4 +
 net/core/netpoll.c          |    2
 6 files changed, 149 insertions(+), 5 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4ea7e386
    • E
      af_packet: Teach to listen for multiple unicast addresses. · d95ed927
      由 Eric W. Biederman 提交于 
      The the PACKET_ADD_MEMBERSHIP and the PACKET_DROP_MEMBERSHIP setsockopt
calls for af_packet already has all of the infrastructure needed to subscribe
to multiple mac addresses.  All that is missing is a flag to say that
the address we want to listen on is a unicast address.

So introduce PACKET_MR_UNICAST and wire it up to dev_unicast_add and
dev_unicast_delete.

Additionally I noticed that errors from dev_mc_add were not propagated
from packet_dev_mc so fix that.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d95ed927
  23. 20 5月, 2009 1 次提交
  25. 19 5月, 2009 6 次提交
  27. 18 5月, 2009 3 次提交
  29. 16 5月, 2009 1 次提交
    • M
      libata: Media rotation rate and form factor heuristics · 4bca3286
      由 Martin K. Petersen 提交于 
      This patch provides new heuristics for parsing both the form factor and
media rotation rate ATA IDENFITY words.

The reported ATA version must be 7 or greater and the device must return
values defined as valid in the standard.  Only then are the
characteristics reported to SCSI via the VPD B1 page.

This seems like a reasonable compromise to me considering that we have
been shipping several kernel releases that key off the rotation rate bit
without any version checking whatsoever.  With no complaints so far.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      4bca3286