- 17 5月, 2007 1 次提交
-
-
由 Dave Jiang 提交于
Adding memory-controller and l2-cache-controller entries to be used by EDAC as of_devices for MPC8540 ADS, MPC8548 CDS, and MPC8560 ADS. Also fixed up the size of the PCI node on MPC8560 ADS. Signed-off-by: NDave Jiang <djiang@mvista.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 12 5月, 2007 1 次提交
-
-
由 Mark A. Greer 提交于
Add the device tree source file for the prpmc2800 line of processor PMCs. Several of the property values are updated by the bootwrapper but sane defaults have been chosen in case the bootwrapper can't determine the exact processor board variant. The defaults should allow the kernel to boot despite having non-optimal device tree property values. Signed-off-by: NMark A. Greer <mgreer@mvista.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 10 5月, 2007 2 次提交
-
-
由 Scott Wood 提交于
The MPC834x_MDS device tree's PCI non-prefetchable MMIO range was specified incorrectly. Both the local and bus addresses start at 0x90000000. Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Scott Wood 提交于
The MPC832x_MDS device tree's PCI non-prefetchable MMIO range was specified incorrectly. Both the local and bus addresses start at 0x90000000. Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 08 5月, 2007 2 次提交
-
-
由 David Gibson 提交于
Add a device tree for the Ebony evaluation board (440GP based). This tree is not complete or finalized. This tree needs a version of dtc recent enough to include reference-to-labels to process. Signed-off-by: NDavid Gibson <dwg@au1.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Josh Boyer 提交于
Add Holly DTS file Signed-off-by: NStephen Winiecki <stevewin@us.ibm.com> Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 07 5月, 2007 2 次提交
-
-
由 Domen Puncer 提交于
Add fsl-i2c to mpc5200 i2c node in device tree, and enable FSL_SOC. Tested to work with built-in eeprom on lite5200b. Signed-off-by: NDomen Puncer <domen.puncer@telargo.com> Signed-off-by: NSylvain Munaut <tnt@246tNt.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Domen Puncer 提交于
Three trivial DTS fixes: -Mark Lite5200(b) boards as "mpc5200" compatible. On efika the firmware already does that. -Fix mscan interrupt. -Fix wakeup GPIO address. Signed-off-by: NDomen Puncer <domen.puncer@telargo.com> Signed-off-by: NSylvain Munaut <tnt@246tNt.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 02 5月, 2007 1 次提交
-
-
由 Kim Phillips 提交于
phy-connection-type now supersedes the interface property. Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 24 4月, 2007 1 次提交
-
-
由 Grant Likely 提交于
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 30 3月, 2007 2 次提交
-
-
由 Jon Loeliger 提交于
This patch provides the basic MPC8544 DS platform code and config. Follow-up patches will add peripherals such as PCI and SATA. Signed-off-by: NXianghua Xiao <x.xiao@freescale.com> Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com> Signed-off-by: NYork Sun <yorksun@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com> Signed-off-by: NJon Loeliger <jdl@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Michael Barkowski 提交于
Add support for the MPC8323E Reference Development Board (RDB). The board is a mini-ITX reference board with 64M DDR2, 16M flash, USB, PCI, 10/100 ethernet, serial, and phone ports. Signed-off-by: NMichael Barkowski <michael.barkowski@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 27 3月, 2007 1 次提交
-
-
由 Zhang Wei 提交于
Signed-off-by: NZhang Wei <wei.zhang@freescale.com> Signed-off-by: NJon Loeliger <jdl@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 09 3月, 2007 1 次提交
-
-
由 Stuart Yoder 提交于
The #cpus property is unused and undocumented and is therefore being removed. Signed-off-by: NStuart Yoder <stuart.yoder@freescale.com> Acked-by: NDavid Gibson <david@gibson.dropbear.id.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 18 2月, 2007 4 次提交
-
-
由 Kumar Gala 提交于
* Removed explicit linux,phandle usage. Use references and labels now * Removed interrupts property from openpic node * Removed interrupt-parent property from openpic node that pointed to itself Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Acked-by: NJon Loeliger <jdl@freescale.com>
-
由 Kumar Gala 提交于
* Fixed up top level compatible property for all boards * Removed explicit linux,phandle usage. Use references and labels now * Fixed phy-phandles for TSEC3/4 in mpc8548cds.dts Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Renamed the MPC8323 MDS and defconfig to match the naming convention followed by other MDS boards. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
The MPC836x PB board is really just one part of the MPC836x MDS. We currently name all other PB boards as MDS. Removed all references to PB and replaced with MDS. Additionally renamed the .dts to match the defconfig (mpc836x_mds*). Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 17 2月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
* Fixed up top level compatible property for all boards * Removed explicit linux,phandle usage. Use references and labels now * Fixed interrupt sense attribute, some interrupts were marked edge, that are level Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 16 2月, 2007 1 次提交
-
-
由 Timur Tabi 提交于
The 'linux,boot-cpu' property is obsolete, so remove it from all of the DTS files and from booting-without-of.txt. The boot CPU is actually defined in the device tree header, and U-Boot sets that field. The device tree compiler also complains if the property exists. Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NStuart Yoder <stuart.yoder@freescale.com> Acked-by: NDavid Gibson <dwg@au1.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 14 2月, 2007 2 次提交
-
-
由 Timur Tabi 提交于
This patch adds a defconfig and a DTS for the MPC8349E-mITX-GP, a variant of the MPC8349E-mITX. USB is disabled because the only USB port is not setup properly by firmware/kernel Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Andy Fleming 提交于
Add support for the MPC8568 MDS reference board Signed-off-by: NAndrew Fleming <afleming@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 13 2月, 2007 1 次提交
-
-
由 Grant Likely 提交于
Much needed refinement of mpc5200 device tree binding specifications. Short list: - drop mpc52xx designator; only two supported chips exist, 5200 and 5200b. It's premature to refer to them as '52xx'. - Specify optional 'model' and 'revision' properties in the soc5200 node - Specify reqiured 'cell-index' property to identify between multiple SOC devices of the same type. (Useful for arbitrating shared register access) - Specify optional 'port-number' property for adjusting the logical serial port assignments. - Specify optional 'has-wdt' property for gpt0 node. - Add system-frequency property to soc5200 node Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 10 2月, 2007 2 次提交
-
-
由 Guennadi Liakhovetski 提交于
Linkstation systems capable of running mainline kernels use u-boot as a bootloader, so, specifying a suitable kernel command is not a problem. Don't guess. Also extend linkstation_defconfig to support the linkstation HS model with a IT8212 IDE controller and kuroboxHD/HD-HLAN linkstation models with a tulip ethernet chip. The latter also require a slightly different .dts file, which is also included with this patch. Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
The MPC834x SYS board has always been called the MPC834x MDS since its public release. Removed all references to SYS and replaced with MDS. Additionally renamed the .dts to match the defconfig (mpc834x_mds*). Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 08 2月, 2007 2 次提交
-
-
由 Li Yang 提交于
Added a new dr_mode property to describe what mode the DR controller is being used in (host, device, OTG). Updated the MPC8349E MDS dts with this new property. Signed-off-by: NLi Yang <leoli@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kim Phillips 提交于
Add support for the MPC8313E Reference Development Board (RDB). The board is a mini-ITX reference board with 128M DDR2, 8M flash, 32M NAND, USB, PCI, gigabit ethernet, and serial. Signed-off-by: NWilson Lo <Wilson.Lo@freescale.com> Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 07 2月, 2007 4 次提交
-
-
由 Vitaly Bordug 提交于
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the current kernel. Current patch fixes it, as well as other inconsistencies expressed, that do not permit targets from working properly: - Updated dts with a chosen node with interrupt controller, - fixed messed device IDs among CPM2 SoC devices, - corrected odd header name and fixed type in defines, - Added 82xx subdir to the powerpc/platforms Makefile, missed during initial commit, - new solely-powerpc header file for 8260 family (was using one from arch/ppc, this one cleaned up from the extra stuff), in fact for now a placeholder to get the board-specific includes for stuff not yet capable to live with devicetree peeks only - Fixed couple of misprints in reference mpc8272 dts. Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Vitaly Bordug 提交于
This contains important fixes for the CPM2 PIC code. Eliminated CPM_IRQ_OFFSET, pulling the respective interrupt numbers from the interrupt mapping. Updated devicetree files to reflect that. Changed direct IC-related IO accesses to the IO accessors. Fixed all the sense values to keep coherency with ipic. In the current code, CPM2 stuff will have no IRQs and hence could be hardly usable. Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Vitaly Bordug 提交于
This add support of the Freescale mpc86xads reference board to arch/powerpc. Supported SMC1 and SMC2 (UART and serial console), FEC 100Mbps Ethernet, SCC1 Ethernet (10Mbps hdx) Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Vitaly Bordug 提交于
This adds the core 8xx stuff and specifically mpc885ads board-specific bits to arch/powerpc. Respective Kconfig has been cleaned up from the stuff not yet ported over to avoid confusion. Updated and cleaned version. Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 31 1月, 2007 1 次提交
-
-
由 Kim Phillips 提交于
Add the mpc8323emds device tree source (dts) Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 22 1月, 2007 1 次提交
-
-
由 Grant Likely 提交于
Documentation-only change. The 5200 device tree layout has not yet stablized, so nobody should depend on the layout of the tree. Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Acked-by: NSylvain Munaut <tnt@246tNt.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 09 1月, 2007 1 次提交
-
-
由 Grant Likely 提交于
This corrects the documented interface for mpc52xx device trees. Sound devices should be using 'sound' for the device_type field, not the type of sound interface. Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Acked-by: NSylvain Munaut <tnt@246tNt.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 04 12月, 2006 3 次提交
-
-
由 Guennadi Liakhovetski 提交于
Support for the Kurobox(HG)/LinkStation-I NAS systems by Buffalo Technology, should be also applicable to the PPC TeraStation family. Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Grant Likely 提交于
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Acked-by: NSylvain Munaut <tnt@246tNt.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Zang Roy-r61911 提交于
The following patch adds a tsi108/9 pci interrupt controller host. On mpc7448hpc2 board, pci_irq_fixup function is removed, which makes the pci_read_irq_line be the default pci irq fixup. Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 06 10月, 2006 1 次提交
-
-
由 Timur Tabi 提交于
Add the DTS for the Freescale MPC 8349E-mITX reference board. Contact Vitesse for the driver for the VSC 7385. Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 04 10月, 2006 2 次提交
-
-
由 Li Yang 提交于
Add MPC8360EMDS default device-tree source file Signed-off-by: NLi Yang <leoli@freescale.com> Signed-off-by: NJiang Bo <Tanya.jiang@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Vitaly Bordug 提交于
This adds current dts file used with MPC8272ADS, introducing new mdio bitbang defines, as well as fully-CPM2-SoC board design. Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
-