Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixing following sparse warning
>drivers/net/wireless/mwl8k.c:2780:15: warning: incorrect type in assignment (different base types)
>drivers/net/wireless/mwl8k.c:2780:15:    expected restricted unsigned short [usertype] channel
>drivers/net/wireless/mwl8k.c:2780:15:    got unsigned short [unsigned] [usertype] hw_value
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The intent here was to check whether key->cipher was WEP40 or WEP104.
We do a similar check correctly in several other places in this file.
The current condition is always true.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Alexandre Oliva <oliva@lsd.ic.unicamp.br> says:

"It's an issue brought about by GCC 4.7's partial-inlining, that ends up
splitting the udelay function just at the wrong spot, in such a way that
some sanity checks for constants fails, and we end up calling
bad_udelay.

This patch fixes the problem.  Feel free to push it upstream if it makes
sense to you."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The brcmsmac driver isn't a PCI driver any more, it's a bcma one.  The
PCI device has been resumed by the PCI driver (the generic PCI layer,
really), we should be resuming just our own driver state.

Also add pr_debug() calls to show that we now actually get the
suspend/resume events.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now the low-level driver actually gets informed that it is getting suspended and resumed.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the following build warning:

drivers/net/wireless/iwlwifi/iwl-scan.c: In function ‘iwlagn_request_scan’:
drivers/net/wireless/iwlwifi/iwl-scan.c:572: warning: ‘cmd_len’ may be used uninitialized in this function
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Documentation states that the KeyMiss flag is only valid if RxFrameOK is
unset, however empirical evidence has shown that this is false.
When KeyMiss is set (and RxFrameOK is 1), the hardware passes a valid frame
which has not been decrypted. The driver then falsely marks the frame
as decrypted, and when using CCMP this corrupts the rx CCMP PN, leading
to connection hangs.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Same devices can generate interrupt without properly setting bit in
INT_SOURCE_CSR register (spurious interrupt), what will cause IRQ line
will be disabled by interrupts controller driver.

We discovered that clearing INT_MASK_CSR stops such behaviour. We
previously first read that register, and then clear all know interrupt
sources bits and do not touch reserved bits. After this patch, we write
to all register content (I believe writing to reserved bits on that
register will not cause any problems, I tested that on my rt2800pci
device).

This fix very bad performance problem, practically making device
unusable (since worked without interrupts), reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=658451

We previously tried to workaround that issue in commit
4ba7d999 "rt2800pci: handle spurious
interrupts", but it was reverted in commit
82e5fc2a
as thing, that will prevent to detect real spurious interrupts.
Reported-and-tested-by: NAmir Hedayaty <hedayaty@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is basically just a cleanup.  Large positive numbers get counted as
negative but then get implicitly cast to positive again for the checks
that matter.

This does make a small difference in ipw_handle_promiscuous_rx() when we
test "if (unlikely((len + IPW_RX_FRAME_SIZE) > skb_tailroom(rxb->skb)))"
It should return there, but we don't return until a couple lines later
when we test "if (len > IPW_RX_BUF_SIZE - sizeof(struct ipw_rt_hdr)) {".
The difference is that in the second test the sizeof() means that there
is an implied cast to unsigned.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An Oops has once been observed, when the SDIO card had been ejected during
IO. The PC value shows, that the dev pointer in b43_op_stop() was NULL.

(I moved the NULL check before the lock, based upon a suggestion from
Julian Calaby <julian.calaby@gmail.com>. -- JWL)
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It appears that you can only read the sprom contents with aligned 16-bit
reads: anything else causes at least some versions of the broadcom
chipset to abort the PCI transaction, returning 0xff.

This apparently doesn't trigger very often, because most setups don't
use an external srom chip, and the OTP sprom loading doesn't have this
issue.  But at least the current 11" Macbook Air does trigger it, and
wireless communications were broken as a result.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The commit "ath9k: Fix invalid noisefloor reading due to channel update"
preserves the current channel noisefloor readings before updating
channel type at the same channel index. It is also updating the curchan
pointer. As survey updation is also referring curchan pointer to fetch
the appropriate index, which might leads to invalid memory access. This
patch partially reverts the change and stores the noise floor history
buffer before updating channel type w/o updating curchan.

Cc: stable@kernel.org
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Reported-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the memory allocation 'nvram_ularray = kmalloc(varsize,
GFP_ATOMIC);' fails we'll leak the memory allocated to 'vbuffer' when
we return -ENOMEM from the function.

This patch resolves the leak by kfree()'ing the allocated memory
before the return.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

also remove an unused macro and a function declaration
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When downloading firmware into the device, the driver fails to check the
return when allocating an skb. When the allocation fails, a BUG can be
generated, as seen in https://bugzilla.redhat.com/show_bug.cgi?id=771656.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath6kl driver is causing build failures when the ath6kl bits are
not built as modules.  A better fix is forthcoming in a future release,
but for now lets revert the problematic code.

This reverts the following commits:

	fde57764
	d70385a2
	59d954ddSigned-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In case of firmware crash, reload the firmware and reconfigure it
by triggering ieee80211_hw_restart; mac80211 utility function.

V2 Addressed following comments from Lennert:
 - Stop the queues during reload
 - Removed atomic_t declaration for hw_restart
 - Extend the firmware reload support for sta firmware as well
 - Other misc changes
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

for EDMA chip AR_Q_TXE (tx enable for each queue) is read only
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the latest Ralink vendor drivers, this seems to be the real
RF chipset type.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When USB driver requires padding at the end of frame or URB it will report
this need by increasing return value of get_tx_data_len callback. Common
USB code uses that return value as desired URB length.

Ensure that appropriate part of skb's tailroom exists and is zeroed.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
--
 drivers/net/wireless/rt2x00/rt2x00usb.c |   16 +++++++++++++---
 1 files changed, 13 insertions(+), 3 deletions(-)
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Older USB drivers does not append end padding to skb but instead report
it in size of data to be transmitted to HW. rt2800usb should follow that
behaviour. Custom write_tx_data callback which was adding pad to skb
is not be needed any more.

Thanks to this patch frames handed back from rt2800usb to mac80211 will
no longer contain end padding.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the latest USB ID database these are all RT2770 / RT2870 / RT307x
devices.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Testing on the openSUSE wireless forum has shown that a Linksys
WUSB54GC v3 with USB ID 1737:0077 works with rt2800usb when the ID is
written to /sys/.../new_id. This ID can therefore be moved out of UNKNOWN.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removes reset_port since it isn't used anywhere as suggested by Johannes Berg.
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9003 chips read tx status from ring buffer whose max number of
status descriptor is mininal compared to max number of tx buffers.
On a stress condition, it can be easily overflown which might cause
false tx hung detection. Though increasing number of max status
descriptors consumes more memory, it helps to avoid false positive
chip resets.

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fix firmware error on "iw dev wlan0 scan passive" for
hardware scanning (with disable_hw_scan=0 module parameter).

 iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
 iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
 iwl3945 0000:03:00.0: Start IWL Error Log Dump:
 iwl3945 0000:03:00.0: Status: 0x0002A2E4, count: 1
 iwl3945 0000:03:00.0: Desc       Time       asrtPC blink2 ilink1  nmiPC   Line
 iwl3945 0000:03:00.0: SYSASSERT     (0x5) 0041263900 0x13756 0x0031C 0x00000 764
 iwl3945 0000:03:00.0: Error Reply type 0x000002FC cmd C_SCAN (0x80) seq 0x443E ser 0x00340000
 iwl3945 0000:03:00.0: Command C_SCAN failed: FW Error
 iwl3945 0000:03:00.0: Can't stop Rx DMA.

We have disable ability to change passive scanning to active on
particular channel when traffic is detected on that channel. Otherwise
firmware will report error, when we try to do passive scan on radar
channels.
Reported-and-debugged-by: NPedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have two such functions.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove these helpers, some are not unused at all, one can be
unrolled in place of use.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Get rid of two inline functions related and simplify a bit
rts_retry_limit calculations.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make function static and change antenna number inline.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This save us about 20k of text size, and should have no impact on
performance as hot paths do not use much I/O.

Before:
   text	   data	    bss	    dec	    hex	filename
 108512	   1784	    168	 110464	  1af80	drivers/net/wireless/iwlegacy/iwl3945.ko
 165730	   2164	    156	 168050	  29072	drivers/net/wireless/iwlegacy/iwl4965.ko
  91942	    328	     48	  92318	  1689e	drivers/net/wireless/iwlegacy/iwlegacy.ko

After:
   text	   data	    bss	    dec	    hex	filename
  95556	   1784	    168	  97508	  17ce4	drivers/net/wireless/iwlegacy/iwl3945.ko
 154853	   2164	    156	 157173	  265f5	drivers/net/wireless/iwlegacy/iwl4965.ko
  91634	    328	     48	  92010	  1676a	drivers/net/wireless/iwlegacy/iwlegacy.ko
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We use "rate_index" like this:
	rate = iwl3945_rates[rate_index].plcp;
The iwl3945_rates[] array has IWL_RATE_COUNT_3945 elements so the
limit here is off by one.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>