DMA data width and packet size information is only required at channel
configuration time. Any information passed from platform data is passed
directly to the DMA40 driver to use during channel allocation, but these
pieces of information are subsequently ignored by the driver, so we may
as well remove them.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Devices which utilise DMA use the same device numbers for transmitting
and receiving. In this patch we encode the source and destination
information into one single attribute. We can subsequently exploit the
direction attribute to see which of the transfer directions are being
described. This also lessens the burden on platform data.

Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This removes <mach/hardware.h> and <mach/db8500-regs.h>
from the Ux500, merging them into the local include
"db8500-regs.h" in mach-ux500. There is some impact
outside the ux500 machine, but most of it is dealt with
in earlier patches.

Contains portions of a clean-up patch from Arnd Bergmann.

Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This moves the DMA40 platform data header from <plat/ste_dma40.h>
to <linux/platform_data/dma-ste-dma40.h> where is belongs.

Cc: Dan Williams <djbw@fb.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Andreas Westin <andreas.westin@stericsson.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the nomadik include directories
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NAlessandro Rubini <rubini@unipv.it>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andreas Westin <andreas.westin@stericsson.com>

At the request of Arnd Bergmann this patch moves all SoC
platform devices found in sysfs from /sys/devices/platform to
/sys/devices/soc<SoCNum>/. It is believed as the devices are
SoC specific and a /sys/devices/soc node has recently
become available, that this would be a more appropriate place to
display the data.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch provides a means for any device within ux500
platform code to allocate its own parent. This is particularly
prudent with the introduction of /sys/devices/socX, as a
device can now proclaim to be integral part of an SoC, rather
than a more generic platform device. Latter patches make good
use of this functionality.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This change is needed after 62285963 "usb: musb: drop a
gigantic amount of ifdeferry", where CONFIG_USB_MUSB_PERIPHERAL
& CONFIG_USB_MUSB_HOST has been removed.
Signed-off-by: NPhilippe Langlais <philippe.langlais@linaro.org>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The mach-ux500/usb.c was referencing DMA macros, but not
including <linux/dma-mapping.h> so it didn't compile. Fixed by
a proper #include.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

USB resources and DMA40 configurations are dynamically with
the data provided in ux500_add_usb() call. Though only DMA40
configurations differ between U8500 and U5500 (USB resource
are common between them).
Signed-off-by: NMian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>