Push the prepare phase for FDB operations down to the DSA drivers, with
a new port_fdb_prepare function. Currently only mv88e6xxx is affected.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link status is polled by the generic phy layer, there's no need to
duplicate that polling with additional polling.  This additional polling
adds additional MDIO traffic, and races with the generic phy layer,
resulting in missing or duplicated link status messages.
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code sets user ports to perform auto negotiation using the
phy. CPU and DSA ports are configured to full duplex and maximum speed
the switch supports.

There are however use cases where the CPU has a slower port, and when
user ports have SFP modules with fixed speed. In these cases, port
settings to be read from a fixed_phy devices. The switch driver then
needs to implement the adjust_link op, so the port settings can be
set.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement port_pvid_set and port_vlan_add to add new entries in the VLAN
hardware table, and join ports to them.

The patch also implement the STU Get Next and Load Purge operations,
since it is required to have a valid STU entry for at least all VLANs.

Each VLAN has its own forwarding database, with FID num_ports+1 to 4095.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the VTU Load Purge operation and implement the
port_vlan_del driver function to remove a port from a VLAN entry, and
delete the VLAN if the given port was its last member.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the port_pvid_get and vlan_getnext driver functions required
to dump VLAN entries from the hardware, with the VTU Get Next operation.

Some functions and structure will be shared with STU operations, since
their table format are similar (e.g. STU data entries are accessible
with the same registers as VTU entries, except with an offset of 2).
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the prototype of port_getnext to include a vid parameter.

This is necessary to introduce the support for VLAN.

Also rename the fdb_{add,del,getnext} function pointers to
port_fdb_{add,del,getnext} since they are specific to a given port.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit f1d5ca43, reversing
changes made to 4933d85c.

I applied v2 instead of v3.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add register definitions #defines for accessing the EEPROM.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a low level function for the ATU Load operation, and provide FDB add
and delete wrappers functions.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds a low level _mv88e6xxx_atu_getnext function and helpers
to rewrite the mv88e6xxx_port_fdb_getnext operation.

A mv88e6xxx_atu_entry structure is added for convenient access to the
hardware, and GLOBAL_ATU_FID is defined instead of the raw 0x01 value.

The previous implementation did not handle the eventual trunk mapping.
If the related bit is set, then the ATU data register would contain the
trunk ID, and not the port vector.

Check this in the FDB getnext operation and do not handle it (yet).
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the fdb_{add,del,getnext} function pointer in favor of new
port_fdb_{add,del,getnext}.

Implement the switchdev_port_obj_{add,del,dump} functions in DSA to
support the SWITCHDEV_OBJ_PORT_FDB objects.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the temperature sensing code for mv88e6352 and mv88e6320 families
into mv88e6xxx.c to simplify adding support for additional chips.

With this change, mv88e6xxx_6320_family() no longer needs to be
a global function and is made static.

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MV88E6320 and MV88E6321 are largely compatible to MV886352,
but are members of a different chip family.
Signed-off-by: NAleksey S. Kazantsev <ioctl@yandex.ru>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6172 is part of the mv88e6352 family of devices. Move support
for it out of the mv88e6171 driver into the mv88e6352, which results
in some simplifications to the code.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use defines for registers, shifts and bits in the remaining register
accesses in the individual drivers, in order to aid readability.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that setting up a port is identical for all switches, centralisers
the code looping over all the ports to set them up.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port setup code in the individual drivers is identical for 6123,
6171, and 6352, and very similar in 6131. Move it all into mv88e6xxx,
using the chip families to differentiate on features.

Similarly, the global setup is also very similar. Move the majority
into mv8e6xxx.

The chips themselves fall into families. Add helpers which uses the
device IDs to determine if a device is a member of a family or not.
Add some additional device IDs to the existing list, to make these
helper functions more complete. However these IDs are not yet added to
the probe functions.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than refer to registers by number, define mnemonics. Also
define mnemonics for the commonly used bits within the registers.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reading the statistics from the hardware is the same for all
chips. What differs is the number of available statistics. Have just
one copy of the code in the shared mv88e6xxx.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the common code for reading and writing phy registers into the
shared mv88e6xxx.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These functions could in future be used by other drivers. Move them
into the shared area.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell switches are all reset in nearly the same way. The only
difference is if the PPU should be enabled or not. Move this
code into the shared mv88x6xxx.c.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a step towards consolidating code, consistently set the
number of ports in the private state structure, and make use of it in
loops.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get the switch id and save it away in the private mv88x6xxx structure
in a centralised piece of code, rather than each driver doing it itself.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for manipulating switch fdb entries by pointing to the
ndo_fdb functions implemented for mv88e6xxxx.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This prepares the driver for hardware bridging.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code used and needed in mv886xxx.c should be initialized there as well,
so factor it out from the individual initialization files.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable EEE support for MV88E6352.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6352 allows access to the port phys via an internal mdio bus
which is accessed using registers in the GLOBAL 2 range. The mv88e6171
and probably other devices use the same mechanism. Move this code into
the shared mv88e6xxx.c library.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some busy bits are available in the global register 1, such as the ATU
Busy bit. We may want to use this function to wait for them to change,
so add a new parameter to mv88e6352_wait() instead of hard-coding
REG_GLOBAL2.

In the meantime, since the REG_READ() macro already checks for error,
remove the redundant check for ret < 0.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Display sw_in_discards, sw_in_filtered, and sw_out_filtered for chips
supported by mv88e6123_61_65 and mv88e6352 drivers.

The variables are provided in port registers, not the normal status registers.
Mark by adding 0x100 to the register offset and add special handling code
to mv88e6xxx_get_ethtool_stats.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report switch register values to ethtool.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MV88E6352 supports read and write access to its configuration eeprom.

There is no means to detect if an EEPROM is connected to the switch.
Also, the switch supports EEPROMs with different sizes, but can not detect
or report the type or size of connected EEPROMs. Therefore, do not implement
the get_eeprom_len callback but depend on platform or devicetree data to
provide information about EEPROM presence and size.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MV88E6352 supports reading the chip temperature from two PHY registers,
6:26 and 6:27. Report it using the more accurate register 6:27.
Also report temperature limit and alarm.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MV88E6176 is mostly compatible to MV88E6352 and is documented
in the same functional specification. Add support for it.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell 88E6352 is mostly compatible to MV88E6123/61/65,
but requires indirect phy access. Also, its configuration
registers are a bit different.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev.  From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.

So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we introduced an additional multiplexing/demultiplexing layer
with commit 3e8a72d1 ("net: dsa: reduce number of protocol hooks")
that lives within the DSA code, we no longer need to have a given switch
driver tag_protocol be an actual ethertype value, instead, we can
replace it with an enum: dsa_tag_protocol.

Do this replacement in the drivers, which allows us to get rid of the
cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not
need it anymore.
Suggested-by: NAlexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>