Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

C2port implements a two wire serial communication protocol (bit
banging) designed to enable in-system programming, debugging, and
boundary-scan testing on low pin-count Silicon Labs devices.

Currently this code supports only flash programming through sysfs
interface but extensions shoud be easy to add.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide the BQ27000 slave interface driver.

Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
protocol of the master functions of the Benchmark HDQ and the Dallas
Semiconductor 1-Wire protocols.  These protocols use a single wire for
communication between the master (HDQ/1-Wire controller) and the slave
(HDQ/1-Wire external compliant device).

This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms.

Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Export the w1_read_8 function for use of drivers.  The OMAP HDQ
driver(drivers/w1/masters/omap_hdq.c) uses this function.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the Dallas DS1390/93/94 SPI RTC chip.
Signed-off-by: NMark Jackson <mpfj@mimc.co.uk>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide the basic "get" and "set" functionality for the Epson RX-8581 I2C
RTC.  It currently does not support the RTC's Alarm or Fixed-cycle timer.

[akpm@linux-foundation.org: need log2.h for ilog2(), remove unneeded initialisation]
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds support for the RTC provided by the Wolfson Microelectronics
WM8350.

This driver was originally written by Graeme Gregory and Liam Girdwood,
though it has been modified since then to update it to current mainline
coding standards and for API completeness.

[akpm@linux-foundation.org: s/schedule_timeout_interruptible/schedule_timeout_uninterruptible/ to prevent bogus timeout when signal_pending()]
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Liam Girdwood <linux@wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ics932s401 is a clock generator chip.  This driver allows users to
read the current clock outputs.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

New driver to play with.  As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors.  This driver has been tested on an IntelliStation Z30.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard").  It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.

This driver was first written by Yan Burman.  Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now).  Pavel Machek removed few more features and switched locking from
semaphore to mutex.

Several people have contributed to the database of the axes.

[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NYan Burman <burman.yan@gmail.com>
Signed-off-by: NPavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We're working with an AT91SAM9263 Rev B in our design and I experienced
some inconsistency in spi-based touchscreen usage between our board and
the Atmel evaluation kit we have that runs on a Rev A chip.

The data was apparently delayed by 1 byte and got ridiculous data out of
the touchscreen driver, very strange.  As everything looked normal in
the spi, touchscreen and dma logs, I contacted the Atmel support and
they triggered me on a new HW bug that appeared in the Rev B SPI
controller.

The problem is that the SPI controller on the Rev B needs that the
software reset is performed two times so that it's performed correctly.

Applying the patch below solves the issue on my Rev B board.  I've tested
it as well on my Rev A evaluation kit and it has apparently no unwanted
side effect, things continue to work as expected.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The adt7468 is a follow-on to the adt7463, so plumb in adt7468 support
along the same code paths.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.

Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.

Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver supports the Xilinx XPS GPIO IP core which has the typical
GPIO features.
Signed-off-by: NKiran Sutariya <kirans@xilinx.com>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Cc: <avorontsov@ru.mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It turns out that edac_mc_del_mc will kobject_put the last kref on the
mci object.

If the timing is just right, that means that the mci object is freed
before before i5000_remove_one has a chance to free the resources
associated with it, causing a null pointer exceptions when unloading the
driver.  Insert a kobject_{get,put} pair so that this doesn't happen.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It turns out that if one registers a struct platform_device, the
platform device code expects that platform_device.device->driver points
to a struct driver inside a struct platform_driver.

This is not the case with the ipmi-si, ipmi-msghandler and ibmaem
drivers, which causes the suspend/resume hook functions to jump off into
nowhere, causing a crash.  Make this assumption hold true for these
three drivers.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Acked-by: NCorey Minyard <cminyard@mvista.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds accelerometer and temperature sensor support for Macbook 4.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix bnx2 so that netpoll works properly.  Specifically:

1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a
struct net_device

2) Fix poll_controller method to check every queue in the rx case so frames
aren't missed
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a TX hang reported by Jesper Dangaard Brouer.

When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own.  This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.

In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first.  There could be side effects, and in fact that is
exactly the problem here.

The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits.  A read clears the state
bits.

We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.

Fix this by reading the bottom half before the upper half.
Tested-by: NJesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device.  Unfortunately, that trick no longer
works...

Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run.  Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.

(Above text by me.  Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's
RTL8187B and work fine with new 2.6.27 driver.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvan Kuten <ivan.kuten@promwad.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a crash in path_rec_completion() during an SM up/down loop.  If
more than one path record request is issued, the first completion
releases path->done, allowing ipoib_flush_paths() to free the path,
and thus corrupting it for the second completion.

Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") added the field path->valid and changed the test "if
(!path)" to "if (!path || !path->valid)".  This change made it
possible for a path with an outstanding query to pass the test and
issue another query on the same path.  Having two queries on the same
path leads to a crash.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1325>.
Signed-off-by: NYossi Etigin <yosefe@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ipoib_flush_paths() can hang during an SM up/down loop: if
path_rec_start() fails (for instance, because there is no sm_ah), the
path is still added to the path list by neigh_add_path().  Then,
ipoib_flush_paths() will wait for path->done, but it will never
complete because the request was not issued at all.  Fix this by
completing path->done if issuing the query fails.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1329>.
Signed-off-by: NYossi Etigin <yosefe@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If a P_Key is not present when an interface is created, ipoib_open()
will return after doing napi_enable().  ipoib_open() will be called
again from ipoib_pkey_poll() when the P_Key appears, after NAPI has
already been enabled, and try to enable it again. This triggers a
BUG_ON() in napi_enable().

Fix this by moving the call to napi_enable() to after the test for
P_Key presence.
Signed-off-by: NYossi Etigin <yosefe@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When the iw_cxgb3 module's cxgb3_client "add" func gets called by the
cxgb3 module, the iwarp driver ends up calling the ethtool ops
get_drvinfo function in cxgb3 to get the fw version and other info.
Currently the iwarp driver grabs the rtnl lock around this down call
to serialize.  As of 2.6.27 or so, things changed such that the rtnl
lock is held around the call to the netdev driver open function.  Also
the cxgb3_client "add" function doesn't get called if the device is
down.

So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the
device, the iw_cxgb3 add func gets called with the rtnl_lock held.  If
you load cxgb3, ifconfig up the device, then load iw_cxgb3, the add
func gets called without the rtnl_lock held.  The former causes the
deadlock, the latter does not.

In addition, there are iw_cxgb3 sysfs handlers that also can call down
into cxgb3 to gather the fw and hw versions.  These can be called
concurrently on different processors and at any time.  Thus we need to
push this serialization down in the cxgb3 driver get_drvinfo func.

The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Acked-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.

x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing.  But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.

It's better for the driver to figure this out at init-time.  If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The Lifebook S6420 is the ICH9M-based follow-up to the S6410. The application panel
contains the following keys: lock, mobility center, eco, info.
Whilst key 4 might be more appropriate for help then key 2, I've done things the
S6410 way. I can confirm that backlight control is functional, and that the lock key
activates the Gnome screensaver as expected.
Signed-off-by: NTony Vroon <tony@linx.net>
Acked-by: NJonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: NLen Brown <len.brown@intel.com>

If the initialization of a special QP (e.g. AQP1) fails due to a
software timeout, we have to remove the reference to that special QP
struct from the port struct to stop the driver from accessing the QP,
since it will be/has been destroyed by the caller, eg in this case
ib_mad.
Signed-off-by: NStefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Referencies: http://bugzilla.kernel.org/show_bug.cgi?id=12004Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=11892Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Disabling gpe might interfere with gpe detection/handling,
thus producing "interrupt not handled" errors.
Ironically, disabling of GPE from interrupt context is already
under spinlock, so only userspace needs to start using it.
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Restart current transaction if we recieved unexpected GPEs instead
of needed ones.

http://bugzilla.kernel.org/show_bug.cgi?id=11896Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

There is a possibility that EC might break if next command is
issued within 1 us after write or burst-disable command.
Suggestd-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Make sure we can tell if the GPE storm workaround gets activated,
and avoid flooding the logs afterwards.

http://bugzilla.kernel.org/show_bug.cgi?id=11841
"plenty of line "ACPI: EC: non-query interrupt received,
 switching to interrupt mode" in dmesg"
Signed-off-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

With the better solution for EC interrupt storm issue,
there is no need to use msleep over udelay.

References:
	http://bugzilla.kernel.org/show_bug.cgi?id=11810
	http://bugzilla.kernel.org/show_bug.cgi?id=10724Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>