On CTG+ read out the pipe bpp setting from hardware and fill it into
pipe config. Also check it appropriately.

v2: Don't do the pipe_bpp extraction inside the PCH only code block on
    ILK+.
    Avoid the PIPECONF read as we already have read it for the
    PIPECONF_EANBLE check.

Note: This is already in drm-intel-next-queued as
commit 42571aef
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date:   Fri Sep 6 23:29:00 2013 +0300

    drm/i915: Add support for pipe_bpp readout

but is needed for the following bugfix.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Detangle the additional state of whether or not the hw has the pfit
enabled from whether it has zero size. This allows us to cleanly
distinguish in the code when we expect the pfit to be enabled (for
Haswell pc8), and when the BIOS is confused and needs sanitizing.
Reported-by: Nshui yanwei <yangweix.shui@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68251Tested-by: Nshui yanwei <yangweix.shui@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already have code to disable LCPLL and switch to FCLK, so we need this too.
We still don't call the code to disable LCPLL, but we'll call it when we add
support for Package C8+.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We set the mode based on the port, and we already pass the port as an
argument.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These messages are not really useful since it's very easy to check
which mode is used for each port: The values programmed are based on
the port type, then assigned to the ddi_translations variable.
Currently we use DP mode for ports A-D and FDI mode for port E.

Also, when we add the code to enable/disable PC8+,
intel_prepare_ddi_buffers will be called more often and will eat your
dmesg buffers.

While at it, fix the coding style of the "for" statement above.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Pimp commit message with Paulo's more detailed explanation of
how the ddi translation buffer settings are computed, to answer a
question from Chris.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Same conversion as for hdmi/dp.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

PSR must be enabled after transcoder and port are running.
And it is only available for HSW.

v2: move enable/disable to intel_ddi
v3: The spec suggests PSR should be disabled even before backlight (by pzanoni)
v4: also disabling and enabling whenever panel is disabled/enabled.
v5: make it last patch to avoid breaking whenever bisecting. So calling for
    update and force exit came to this patch along with enable/disable calls.
v6: Remove unused and unecessary psr_enable/disable calls, as notice by Paulo.

CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Drop the psr exit code in the busy ioctl since I didn't merge
that part of the infrastructure yet - it needs more thought.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise the DDI_A_4_LANES bit gets lost and we can't use > 2 lanes
on eDP. This fixes eDP on hsw with > 2 lanes.

Also s/port_reversal/saved_port_bits/ since the current name is
confusing.
Signed-off-by: NStéphane Marchesin <marcheu@chromium.org>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because calling intel_dp_encoder_destroy inside
intel_edp_init_connector is just wrong. This is the initialization
path, so we should properly unwind all the initialization through the
whole caller stack.

On the intel_dp_encoder_destroy function we do the following:
1 - Call i2c_del_adapter
2 - Call drm_encoder_cleanup
3 - If edp:
3.1 - Cancel panel_vdd_work
3.2 - Call ironlake_panel_vdd_of_sync
4 - Free the encoder

And here is how we unwind each specific step:
1 - We have intel_dp_init_connector -> intel_dp_i2c_init ->
    i2c_dp_aux_add_bus -> i2c_add_adapter, so we call
    i2c_del_dapter at intel_dp_init_connector
2 - Call it in the same function that called drm_encoder_init
3 - Call it in the same function that called INIT_DELAYED_WORK
4 - Free it in the same function that allocated it
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NZoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because calling intel_dp_destroy inside intel_edp_init_connector is
just wrong. This is the initialization path, so we should properly
unwind all the initialization through the whole caller stack.

On the intel_dp_destroy function we do the following:
1 - Free edid if it exists
2 - Call intel_panel_fini in case it's eDP
3 - Call drm_sysfs_connector_remove
4 - Call drm_connector_cleanup
5 - Free the connector

And here is how we unwind each specific step:
1 - No need as we still didn't assign anything
2 - No need as we still didn't call intel_panel_init
3 - Call it in the same function that called drm_sysfs_connector_add
4 - Call it in the same function that called drm_connector_init
5 - Free it in the same function that allocated it
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NZoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In case we detect a "ghost eDP", intel_edp_init_connector frees both
the connector and encoder and then returns. On Haswell, intel_ddi_init
then tries to use the freed encoder on the HDMI initialization path
since the following commit:

commit 21a8e6a4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Apr 10 23:28:35 2013 +0200
    drm/i915: don't setup hdmi for port D edp in ddi_init

So now on intel_ddi_init we check for the "ghost eDP" case and return
without trying to initialize HDMI. This way we won't try to read the
freed "intel_encoder" struct in the next "if" statement.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NZoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This way we can simplify the code quite a bit.

Also add a WARN in the sdvo code to complain about a bogus value
and kill the readout code in intel_ddi.c that Jesse sneaked in.
HW state readout for the pixel multiplier will work a bit differently
in the end.

v2: Rebase on top of the fdi pixel mutliplier handling fix.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.

Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.

I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).

So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.

v2: Fix up ilk cpu pll handling.

v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.

v4: Rebase on top of Imre's is_cpu_edp removal.

v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.

v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.

Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This allows us to drop a bunch of ugly hacks and finally implement
what

commit cc464b2a
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Fri Jan 25 16:59:16 2013 -0200

    drm/i915: set TRANSCODER_EDP even earlier

tried to achieve, but that was reverted again in

commit bba2181c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Fri Mar 22 10:53:40 2013 +0100

    Revert "drm/i915: set TRANSCODER_EDP even earlier"

Now we should always have a consistent cpu_transcoder in the
pipe_config.

v2: Fix up the code as spotted by Paulo:
- read the register for real
- assign the right pipes
- break out if the hw state doesn't make sense

v3: Shut up gcc.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With this, that 338 can finally become the correct 337500.

Due to the change we need to adjust the intel_dp_aux_ch function to
set the correct value, so adjust the division and also use
DIV_ROUND_CLOSEST instead of the old "round down" behavior because the
spec says the value "should be programmed to get as close as possible
to the ideal rate of 2MHz".

Quoting Paulo's follow-up to a question from Chris Wilson to explain
what exactly will change:

I use the 337500 value on the next patch, when setting the
ips_linetime value. The correct frequency is 337500, not 338000.

ips_linetime = DIV_ROUND_CLOSEST(mode->htotal * 1000 * 8,
intel_ddi_get_cdclk_freq);
For a mode with htotal of 2640 [0] we'll have: (i) (2640 * 1000 * 8) /
338000 = 62.48, resulting in 62 and (ii) (2640 * 1000 * 8) / 337500 =
62.57 resulting in 63.

For the case inside intel_dp.c:
Previously we were using 338. So with the old formula we were writing
338/2 = 169 to the register. And 337500 / 169 = 1997.04 (we use 337500
here because it's the real clock value). With the new value of
337500/2000 we'll have 168.75, which is 168 on the round-down case and
169 on the round-closest case. If we write 168 to the register, 337500
/ 168 = 2008.92, and 2008.92 is more distant from 2000 than 1997.04.
So with this patch we're changing the formula but still writing the
same correct value to the DP AUX register.

[0]: That's 1920x1080@50Hz on my DP monitor.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Pimp the commit message with Paulo's follow-up.]
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can use this for fetching encoder specific pipe_config state, like
mode flags, adjusted clock, etc.

Just used for mode flags atm, so we can check the pipe config state at
mode set time.

v2: get_config when checking hw state too
v3: fix DVO and LVDS mode flags (Ville)
    get SDVO DTD for flag fetch (Ville)
v4: use input timings (Ville)
    correct command used (Ville)
    remove gen4 check (Ville)
v5: get DDI flag config too
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Tested-by: Paulo Zanoni <przanoni@gmail.com> (the new hsw ddi stuff)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Up to now, we were using a static table to match the clock frequency
with a (r2,n2,p) triplet. Despite this table being big, it's by no mean
comprehensive and we had to fall back to the closest frequency when the
requested TMDS clock wasn't in the table.

This patch computes (r2,n2,p) dynamically and get rid of The Big Table.

v2: Replace the floating point constant 1e6 by 1000000

Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=58497Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
[danvet: s/        /^T/]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We did not mention the workaround name when implementing those. This
should help us track what we already implement.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already have the same check on intel_enable_ddi. This patch
prevents "unclaimed register" messages when the power well is
disabled.

V2: Reset intel_crtc->eld_vld to false after the mode_set function.
V3: Add both "type != INTEL_OUTPUT_EDP" requested.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

dp_init_connector adjusts the encoder type if it is a eDP panel. Use
that to decide whether we should set up a hdmi connector or not.

To do so reorder the hdmi connector setup sequence in ddi_init a bit.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to BSpec the link training sequence for eDP on HSW port-A
should be as follows:

1. link training: clock recovery
2. link training: equalization
3. link training: set idle transmission mode
4. display pipe enable
5. link training: disable (set normal mode)

Contrary to this at the moment we don't do step 3. and we do step 5.
before step 4. Fix this by setting idle transmission mode for eDP at
the end of intel_dp_complete_link_train and adding a new
intel_dp_stop_link_training function to disable link training. With
these changes we'll end up with the following functions corresponding
to the above steps:

intel_dp_start_link_train    -> step 1.
intel_dp_complete_link_train -> step 2., step 3.
intel_dp_stop_link_train     -> step 5.

For port-A we'll call intel_dp_stop_link_train only after enabling the
pipe, for everything else we'll call it right after
intel_dp_complete_link_train to preserve the current behavior.

Tested on HSW/HSW-ULT.

In v2:
- Due to a HW issue we must set idle transmission mode for port-A too
  before enabling the pipe. Thanks for Arthur Runyan for explaining
  this.
- Update the patch subject to make it clear that it's an eDP fix, DP is
  not affected.

v3:
- rename intel_dp_link_train() to intel_dp_set_link_train(), use 'val'
  instead 'l' as var name. (Paulo)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we ever leak a non-DP compliant port width through here, we have a
pretty serious issue. So just rip out all these WARNs - if we need
them it's probably better to have them at a central place where we
compute the dp lane count.

Also use the new DDI width macro for FDI mode.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixup the embarrassing s/intel_dp->DP/temp/ mistake Paulo
spotted.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Introduce some nice #defines for the FDI lane width fields and put
them to good use. Suggested by Ville.

v3: Fixup the mask vs. shift copy&pasta fail Imre Deak spotted, and
use the shift #define also in the mask.

Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need this for two reasons:
- Correct handling of shared fdi lanes on ivb with fastboot.
- Handling fdi link bw limits when we only have two fdi lanes by
  dithering down a bit.

Just search&replace in this patch, no functional change at all.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And put the pfit stuff into substructs while we're at it.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We are trying to have more platform-orthogonal pieces of code. The DDI
code shouldn't mention Haswell.

v2: Fix the email address
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Alway use the alphabetical names in debug/error messages for planes,
pipes and ports, instead of using decimal numbers occasionally.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For a bunch of reason we need to more accurately track this:
- hw pipe state readout for Haswell needs the cpu transcoder.
- We need to know the right cpu transcoder in a bunch of places in
  ->disable and other modeset callbacks.

In the future we need to add hw state readout&check support, too. But
to avoid ugly merge conflicts do the rote sed job now without any
functional changes.

v2: Preserve the cpu_transcoder value when overwriting crtc->config.
Reported by Paulo.

Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: Removed rough whitespace that Chris spotted.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we couldn't find a pipe we shouldn't return true.  This might be even
better as a WARN though, since it should be impossible to have the port
enabled without a pipe selected.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The procedure has now 3 steps:

1. Compute the bpp that the plane will output, this is done in
   pipe_config_set_bpp and stored into pipe_config->pipe_bpp. Also,
   this function clamps the pipe_bpp to whatever limit the EDID of any
   connected output specifies.
2. Adjust the pipe_bpp in the encoder and crtc functions, according to
   whatever constraints there are.
3. Decide whether to use dither by comparing the stored plane bpp with
   computed pipe_bpp.

There are a few slight functional changes in this patch:
- LVDS connector are now also going through the EDID clamping. But in
  a 2nd change we now unconditionally force the lvds bpc value - this
  shouldn't matter in reality when the panel setup is consistent, but
  better safe than sorry.
- HDMI now forces the pipe_bpp to the selected value - I think that's
  what we actually want, since otherwise at least the pixelclock
  computations are wrong (I'm not sure whether the port would accept
  e.g. 10 bpc when in 12bpc mode). Contrary to the old code, we pick
  the next higher bpc value, since otherwise there's no way to make
  use of the 12 bpc mode (since the next patch will remove the 12bpc
  plane format, it doesn't exist).

Both of these changes are due to the removal of the

	pipe_bpp = min(display_bpp, plane_bpp);

statement.

Another slight change is the reworking of the dp bpc code:
- For the mode_valid callback it's sufficient to only check whether
  the mode would fit at the lowest bpc.
- The bandwidth computation code is a bit restructured: It now walks
  all available bpp values in an outer loop and the codeblock that
  computes derived values (once a good configuration is found) has been
  moved out of the for loop maze. This is prep work to allow us to
  successively fall back on bpc values, and also correctly support bpc
  values != 8 or 6.

v2: Rebased on top of Paulo Zanoni's little refactoring to use more
drm dp helper functions.

v3: Rebased on top of Jani's eDP bpp fix and Ville's limited color
range work.

v4: Remove the INTEL_MODE_DP_FORCE_6BPC #define, no longer needed.

v5: Remove intel_crtc->bpp, too, and fix up the 12bpc check in the
hdmi code. Also fixup the bpp check in intel_dp.c, it'll get reworked
in a later patch though again.

v6: Fix spelling in a comment.

v7: Debug output improvements for the bpp computation.

v8: Fixup 6bpc lvds check - dual-link and 8bpc mode are different
things!

v9: Reinstate the fix to properly ignore the firmware edp bpp ... this
was lost in a rebase.

v10: Both g4x and vlv lack 12bpc pipes, so don't enforce that we have
that. Still unsure whether this is the way to go, but at least 6bpc
for a 8bpc hdmi output seems to work.

v11: And g4x/vlv also lack 12bpc hdmi support, so only support high
depth on DP. Adjust the code.

v12: Rebased.

v13: Split out the introduction of pipe_config->dither|pipe_bpp, as
requested from Jesse Barnes.

v14: Split out the special 6BPC handling for DP, as requested by Jesse
Barnes.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We want to compute this earlier. To avoid a big complicated patch,
this patch here just does the big search&replace and still calls the
old functions at the same places.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is used way too often in the enable/disable paths. And will
be even more useful in the future.

Note that correct semantics of this change highly depend upon
correct updating of intel_crtc->config: Like with all other
modeset state, we need to call ->disable with the old config,
but ->mode_set and ->enable with the new config.

v2: Do not yet use the flag in the ->disable callbacks - atm we don't
yet have support for the information stored in the pipe_config in the
hw state readout code, so this will be wrong at boot-up/resume.

v3: Rebased on top of the hdmi/dp ddi encoder merging.

v4: Fixup stupid rebase error which lead to a NULL vfunc deref.

v5: On haswell the VGA port is on the PCH!

v6: s/IS_HASWELL/HAS_DDI/, spotted by Paulo Zanoni. Also add a missing
parameter name in a function declaration.

v7: Don't forget to git add ...
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If TRANS_DDI_FUNC_CTL has been wrongly programmed with an incorrect
port, we are currently trying to read PORT_CLK_SEL(port) with an
uninitialized value.

Handle that case by returning PORT_CLK_SEL_NONE and warning about it.

v2: Move the warning inside intel_ddi_get_crtc_pll (Paulo Zanoni)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We are really talking about the transcoder function here and the disable
version uses trancoder in its name already, so let's try to be
consistent.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Our static analysis tool noticed that 'reg' could be used uninitialized if
we are trying to get a PLL to drive VGA and SPLL is already in use
(plls->spll_refcoung != 0).

In the (error) case above, let's return false to the caller and emit an
error.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Our mode set sequence documentation says audio must be disabled first.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Resolve conflict since the first patch in this series isn't
applied yet. Also bikeshed commit message as suggested by Ben.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Need to initialize the variable wait to false.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some (but not all) of the HDMI registers can be used to control sDVO,
so those registers have two names. IMHO, when we're talking about
HDMI, we really should call the HDMI control register "hdmi_reg"
instead of "sdvox_reg", otherwise we'll just confuse people reading
our code (we now have platforms with HDMI but without SDVO). So now
"struct intel_hdmi" has a member called "hdmi_reg" instead of
"sdvox_reg".

Also, don't worry: "struct intel_sdvo" still has a member called
"sdvo_reg".

v2: Rebase (v1 was sent in May 2012).
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Similarly to:

  commit 6a0d1df3d3a0d2370541164eb0595fe35dcd6de3
  Author: Damien Lespiau <damien.lespiau@intel.com>
  Date:   Tue Dec 11 15:18:28 2012 +0000

      drm/i915: Preserve the FDI line reversal override bit on CPT

DDI port support lane reversal to easy the PCB layouting work. Let's
preserve the bit configured by the BIOS (until we find how to correctly
retrieve the information from the VBT, but this does sound more fragile
then just relying on the BIOS that has, hopefully, been validated
already.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The FDI link has supported link reversal to make the PCB layout
engineer's life easier for quite a while and we have always presered
this bit as we programmed FDI_RX_CTL with a read/modify/write sequence.

We're trying to take a bit more control over what the BIOS leaves in
various register and with the introduction of DDI, started to program
FDI_RX_CTL fully.

There's a fused bit to indicate DMI link reversal and FDI defaults to
mirroring that configuration. We have a bit to override that behaviour
that we need to preserve from the BIOS.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>