Fix sparse warnings on incompatibility between the endianess of the ctrl_flags
field of struct mlx4_en_priv to the srcrb_flags field of struct
mlx4_wqe_ctrl_seg by changing the former to be __be32 instead of u32.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Localized the pdev->dev, and using dma_map instead of pci_map
There are multiple map/unmap operations on data path,
optimizing those by saving redundant pointer access.
Those places were identified as hot-spots when running kernel profiling
during some benchmarks.
The fixes had most impact when testing packet rate with small packets,
reducing several % from CPU load, and in some case being the difference
between reaching wire speed or being CPU bound.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Silence the following warning:
"warn: returning -1 instead of -ENOMEM is sloppy".
Signed-off-by: NSantosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: NJunchang Wang <junchangwang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing fancy:
- sent bytes count is notified in the start_xmit path right before
  updating the owner bit in the hardware Tx descriptor (E. Dumazet)
- avoid useless tp->dev dereferencing in start_xmit (E. Dumazet)

Use of netdev_reset_queue is favored over proper accounting in
rtl8169_tx_clear_range since the latter would need more work for the
same result (nb: said accounting degenerates to nothing in xmit_frags).
Signed-off-by: NIgor Maravic <igorm@etf.rs>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>

Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: NJunchang Wang <junchangwang@gmail.com>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

In 'ql_adapter_initialize'
the first call for 'spin_unlock_irqrestore()' is with hw_flags = 0,
which is as good as 'spin_unlock_irq()' (unconditional interrupt
enabling). If this is intended, then for better performance
'spin_unlock_irqrestore()' can be replaced with 'spin_unlock_irq()'
and 'spin_lock_irqsave()' can be replaced by 'spin_lock_irq()
Signed-off-by: NSantosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix new sparse errors introduced in commit 62212171 (mlx4_en: dont
change mac_header on xmit)
Reported-by: NOr Gerlitz <or.gerlitz@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch recodes the MRRS cap for 5719 A0 devices as a PCI quirk.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Factor out the the existing allocation and free operations
so that they can be used individually.

This is to improve code readability, and also to prepare for
possible future changes like better error recovery and more
dynamic configuration (e.g on-the-fly resizing of the rings).

This change represents a straight up relocation of the existing
code into separate routines without changing any of the contained
code itself.  Local variables are relocated as necessary.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRC reset causes the read DMA engine to go into a mode that breaks up
requests into 256 bytes.  A PHY reset is required to bring it back to
the normal mode.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

for weak memory model architectures to ensure that the chip will DMA
valid BD data.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Loopback on 9K packet fails because the chip has a DMA limit of 4K.  The
loopback test logic uses a single BD for simplicity.  Fix it by reducing
the jumbo packet size to the DMA limit.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

{g|s}etnumtcs() today returns a u8 that is only used by the DCB code
to verify no error occurred. Today the driver implementations return
negative error codes which end up being non-zero so the logic works
out but triggers some sparse warnings.

To fix the sparse warnings convert the return value to an int.

CC: Eilon Greenstein <eilong@broadcom.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

dcb netlink code calls setup_tc to init hardware traffic classes
to use for DCB. At some call sites the return values are not
checked for errors and in one case may return -EINVAL back to
the net/dcbnl.c caller which is expecting a u8.

This fixes some smatch hits and although failures are never
seen in practive its best to check return codes.
Reported-by: NDan Carenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The old code would += the total errors every time
stats were gathered.  Instead, keep a count of short-pkt
and long-pkt counters and then simply add them together
for the rx-over-length stat.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Noticed with the 8168d (-vb-gr, aka RTL_GIGA_MAC_VER_26).

ConfigX registers should only be written while the Config9346 lock
is held.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Reported-by: NNick Bowler <nbowler@elliptictech.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of the big network driver reorg, each vendor directory defaults to
yes, so that older config's can migrate correctly. Looks like this one
got missed.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"num_vfs" is a u32 but we only use the high 16 bits and the low 16bits
are left as zero.  That isn't a problem for little endian systems but it
will break on big endian ones.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pch_gbe_validate_option() modifies 32 bits of memory but we pass
&hw->phy.autoneg_advertised which only has 16 bits and &hw->mac.fc
which only has 8 bits.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects several comments that are either incorrect or formatted
incorrectly for multiline comments.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Correct spelling error caught with codespell.py.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to address several minor issues in
ixgbe_xmit_frame_ring.  Specifically it adds a comment explaining the TXSW
flag, and correctly wraps a line over 80 characters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The e1000_link_stall_workaround_lv() function is always called in non-
atomic context so it should use msleep instead of mdelay.  Also, remove
unnecessary #include <linux/delay.h>.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows the NIC to receive packets with bad FCS
and other errors.  Good for sniffing packets on flakey
networks.

v4:  Only flax rx-over-length errors if pkt is beyond
   maximum expected packet size, not just beyond the MTU.
   This matches the existing logic for this counter.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This can aid with testing the RX logic for bad
CRCs.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows e100 to be configured to append the
Ethernet FCS to the skb.

Useful for sniffing networks.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

tg3_get_stats64() takes tp->lock when dealing with non-serdes bcm5700
and bcm5701 devices.  However, functions that call tg3_halt() have
already acquired tp->lock.  When tg3_get_stats64() is called in
tg3_halt(), deadlock will occur.

This patch fixes the problem by separating the stat gathering code into
a new tg3_get_nstats() function.  tg3_get_stats64() is recoded to call
this function and take tp->lock.  The code that takes tp->lock in
tg3_calc_crc_errors() has been removed.  Function signatures have been
cleaned up too.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to use the new 'saddr' variable not the void 'addr' in
set_mac_address().
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A driver xmit function is not allowed to change skb without special
care.

mlx4_en_xmit() should not call skb_reset_mac_header() and instead should
use skb->data to access ethernet header.

This removes a dumb test : if (ethh && ethh->h_dest)

Also remove this slow mlx4_en_mac_to_u64() call, we can use
get_unaligned() to get faster code.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename e1000e_reload_nvm() to e1000e_reload_nvm_generic() to signify the
function is used for more than one MAC-family type, and set and use it as a
MAC ops function pointer to be consistent with the driver design.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove reference to non-existant function.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rename e1000e_config_collision_dist() to
e1000e_config_collision_dist_generic() to signify the function is used for
more than one MAC-family type, and set and use it as a MAC ops function
pointer to be consistent with the driver design.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>