Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After destroying recv ctx, context state remain same.
Fix it by marking as FREED.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Offload tx timeout recovery to fw recovery func(check_health).
In check_health, first check health of device, if it its ok, then
do tx timeout recovery otherwise device recovery.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to free/alloc host resources during firmware
recovery.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we were allocating device resources during probe and
release them during remove.
Now alloc during interface up and release in interface down.
This helps in device performance, as it doesn't need to keep
track of inactive resources.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We first add mac address in driver local list and then send command to
fw to add same. There are checks in driver to ensure send command doesn't fail
before adding mac address in local list.

But instead fix should be:
Add mac address in fw and if it succeeds, add it in driver local list.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of delaying rcv handshake till interface comes up,
do it just after fw load.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to maintian separate state for alloced and freed skb.
This can be done by null check.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use u64_stats_sync infrastructure to provide 64bit rx/tx
counters even on 32bit hosts.

It is safe to use a single u64_stats_sync for rx and tx,
because BH is disabled on both, and we use per_cpu data.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To properly implement 64bits network statistics on 32bit or 64bit hosts,
we provide one new type and four methods, to ease conversions.

Stats producer should use following template granted it already got an
exclusive access to counters (include/linux/u64_stats_sync.h contains
some documentation about details)

    u64_stats_update_begin(&stats->syncp);
    stats->bytes64 += len;
    stats->packets64++;
    u64_stats_update_end(&stats->syncp);

While a consumer should use following template to get consistent
snapshot :

    u64 tbytes, tpackets;
    unsigned int start;

    do {
        start = u64_stats_fetch_begin(&stats->syncp);
        tbytes = stats->bytes64;
        tpackets = stats->packets64;
    } while (u64_stats_fetch_retry(&stats->lock, syncp));

Suggested by David Miller, and comments courtesy of Nick Piggin.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_needs_gso() is checked twice in the TX path once,
before submitting the skb to the qdisc and once after
it is dequeued from the qdisc just before calling
ndo_hard_start().  This opens a window for a user to
change the gso/tso or tx checksum settings that can
cause netif_needs_gso to be true in one check and false
in the other.

Specifically, changing TX checksum setting may cause
the warning in skb_gso_segment() to be triggered if
the checksum is calculated earlier.

This consolidates the netif_needs_gso() calls so that
the stack only checks if gso is needed in
dev_hard_start_xmit().
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a typo in include/net/netlink.h
should be finalize instead of finanlize
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of this workaround is necessary for all ICHx/PCH parts so one of
the two MAC-type checks can be removed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Originally it was thought there were issues with ICHx/PCH parts with packet
split when jumbo frames were enabled but in fact it is really only when
early-receive is enabled (via ERT register) on these parts.  Use packet
split with jumbos but only when early-receive is not enabled.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY on 82577/82578 has issues when the registers on page 800 are
accessed when in gigabit mode.  Do not clear the Wakeup Control register
when resetting the part since it is on page 800 (and will be cleared on
reset anyway).
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid touching hardware registers when possible, otherwise link negotiation
can get messed up when user-level scripts are rapidly polling the driver to
see if/when link is up.  Use the saved link state information instead when
possible.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added new CAIF protocol type CAIFPROTO_DEBUG for accessing
CAIF debug on the ST Ericsson modems.

There are two debug servers on the modem, one for radio related
debug (CAIF_RADIO_DEBUG_SERVICE) and the other for
communication/application related debug (CAIF_COM_DEBUG_SERVICE).

The debug connection can contain trace debug printouts or
interactive debug used for debugging and test.

Debug connections can be of type STREAM or SEQPACKET.
Signed-off-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously CAIF supported maximum transfer size of ~4050.
The transfer size is now calculated dynamically based on the
link layers mtu size.

Signed-off-by: Sjur Braendeland@stericsson.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CAIF Remote File Manager may send or receive more than 4050 bytes.
Due to this The CAIF RFM service have to support segmentation.

Signed-off-by: Sjur Braendeland@stericsson.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow control is not used by all CAIF services.
The usage of flow control is now part of the gerneal
initialization function for CAIF Services.

Signed-off-by: Sjur Braendeland@stericsson.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also separate out an _EXTRAVERSION similar to the core kernel.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables IEEE802.3az (a.k.a. Energy Efficient Ethernet) on the
new 82579 LOMs.  An optional module parameter is provided to disable the
feature if desired.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not check for all the bits in E1000_FWSM_MODE_MASK when checking for
manageability on 82577/82578; only check if iAMT is enabled.  Both of the
manageability checks (for 82577/82578 and ICHx) must check the firmware
valid bit too since the other bits are only valid when the latter is set.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 82577/82578 parts have half-duplex statistics in PHY registers.  These
need only be read when in half-duplex and should all be read at once rather
than one at a time to prevent excessive cycles of acquiring/releasing the
PHY semaphore.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not acquire and release the PHY unnecessarily for parts that return
from this workaround without actually accessing the PHY registers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor the loopback setup code to first handle the only 10/100 PHY
supported by the driver if applicable and then handle the 1Gig PHYs in a
switch statement for PHY-specific setups.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove an unused flag and replace couple constants with enums.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update to latest FW API.  Most changes here pertain to port types and
querying FW for parameter values.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ndo_get_stats64, remove ndo_get_stats.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the pci_error_handlers methods for EEH.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split some existing initialization code into a separate function for use
by EEH next.  No functional changes.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle the larger flash memories on newer boards:

- get the size and number of sectors by probing the flash
- writes and erases can take longer, adjust the timeouts for these operations
- the FW image can be at different locations depending on flash size,
  find its location dynamically as well.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	net/mac80211/mlme.c

For certain set of register, base window addresses are not defined.
In such cases window should not set.
Return with error for such cases to avoid NMI.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>