Add const to functions that return strings that aren't going to be
modified. This addresses some reported compile complaints.

Change-ID: Ic56b1e814ab4d23a50480e7fdec652445f776ee8
Signed-off-by: NJingjing Wu <jingjing.wu@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Cut down on the number of startup log entries by putting a couple behind
debug flags and combining a couple others into a single line.

Change-ID: I708089f086308f84d43f8b6f0e8a634a02d058fb
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As per Eric Dumazet's previous patches:
(see commit (24d2e4a5) - tg3: use napi_complete_done())

Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout

GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>

Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
				rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS

igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result:  941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589

Alignment      Offset         Bytes    Bytes       Recvs   Bytes    Sends
Local  Remote  Local  Remote  Xfered   Per                 Per
Recv   Send    Recv   Send             Recv (avg)          Send (avg)
    8       8      0       0 1176930056  1475.36    797726   16384.00  71905

MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result:  941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763

Alignment      Offset         Bytes    Bytes       Recvs   Bytes    Sends
Local  Remote  Local  Remote  Xfered   Per                 Per
Recv   Send    Recv   Send             Recv (avg)          Send (avg)
    8       8      0       0 1175182320  50476.00     23282   16384.00  71816

i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.

Other drivers were only compile tested.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.

In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The polling routine for i40e was rounding up the budget for Rx cleanup to
1.  This is incorrect as the netpoll poll call is expecting no Rx to be
processed as the budget passed was 0.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().

v2: removed unused variable
v3: removed another unused variable
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump.

Change-ID: I8d9a99f320af43960deba8718eee2d6de50eaf46
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save a little stack space and remove unnecessary strncpy() with a little
string pointer.

Change-ID: Id2719d34710bfc273d3bb445fec085cd04276e88
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 will report Gen 1x1 in the PCI config space as it is on
IOSF bus, so skip the PCI bus link/speed check.

Change-ID: Icd5f5751dc7fb00dccf0d5dc5a0a644948e7062e
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Store off reported PHY capabilities in link_info structure.

Change-ID: Ife0f037c26983ca985dbf79abf33f8f8791369e8
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove a variable declaration inside an if block hiding an existing
declaration at the start of the function.

Also remove a forward function declaration that is no longer needed due
to code re-organization.

Change-ID: I12954668b722718074949c93d74cd20eaacd93e4
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since the flow-director-atr priv flag was added to our ethtool interface,
we don't need the on/off control in debugfs.

Change-ID: Ib3b599916434ab30ccd40074e71d7a81609b5bb5
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Even though the device might be in MFP mode, if there's only one partition
enabled, then we still have plenty of interrupts for managing the Flow
Directory Sideband activity.  This patch enables FD SB in this case.
This patch also reverses the sense of the conditional in order to remove
the negative logic.

Change-ID: I9edf211a6219fc8d159b4be9964f9fd7f4e00bc0
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This version check only applies to very, very old firmware,
that only ran on A0 hardware, which we never shipped and don't
support in this driver anyway. Remove it, before somebody
gets hurt.

Change-ID: I3752d090ff488acf98ee76b075af961e9c968ee4
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 has a way to work around the descriptor WB issue,
this offload helps turn that feature on.

Change-ID: I7ffa67622426bfca5a651417b63e3afcfeb60412
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Only the X722 device now supports 100M SGMII, and nothing supports
100M on 1000Base_T.

Change-ID: I6f44dcd818944edd40041410e6de380f4a359a0c
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are several error messages that have been printing when there is
no functional issue. These messages should be available at debug message
level only.

Change-ID: Id91e47bf942c483563995f30d8705fa53acd5aa3
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some customers wish to be able to control our hardware specific
feature called flow director, at runtime.  This patch enables
ethtool priv flags to control this driver/hardware specific feature.

ethtool --set-priv-flags ethX flow-director-atr off

NOTE: the ethtool ntuple interface controls the flow-director
      sideband rules.

Change-ID: Iba156350b07fa2ce66f53ded51739f9a3781fe0e
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add nlflags to the function comment for ndo_bridge_setlink.

Change-ID: I34c704f307f2a3f7bac3ca4b44e2a094d3d082d6
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump.

Change-ID: If3cd42f6c1b9546beed60faf9c79faab35216f58
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove unused members in the PHY structure and add a new member to store
all the capabilities the PHY has as reported by the FW. This information
will help us determine what speeds the device is capable of when link is
down.

Also add an enum to decode the PHY types the NVM is capable of.
Use the phy_types variable to determine what phy types are possible
when link is down instead of device id as it will be more accurate.

When on a backplane device, we do not support changing any settings,
however we should display all the phy_types we are capable of so if we
see a backplane dev ID set supported and advertised purely based on
the phy_types variable.

Change-ID: Ia75d560f1fcd30c54cbfb7458690c5867559a930
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a module_types variable to the link_info struct to save the module
information from get_phy_capabilities. This information can be used to
determine which speeds the module supports.

Also add a new function update_link_info which updates the module_types
parameter and then calls get_link_info. This function should be called
in place of get_link_info so that the module_types variable stays
up-to-date with the rest of the link information.

The EAS table does not reflect the values that are actually returned,
so instead, basing these values on the Ethernet compliance codes
specified in table 33 of SFF-8436 as these have been accurate.

Use the new variable in ethtool to differentiate between a 10G/1G dual
speed fiber module and a 10G only module.

Change-ID: Ib7585cce321319c10ce15180054c41a6cbd41389
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to desires to write userland drivers, and other requests, without
needing the rest of the include files, the device ids are pulled out
into a standalone file.

Change-ID: Ic0b047dbf9d4b0891892309c1f2079f56d9b60e8
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch moves the internal fw version and fw api version info to be
output in probe.  The nvm version, etrack and oem version info are now
configured for output via ethtool -i.

Change-ID: I05d490093a7137dbefcdef263d014d1e5c9e83d0
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some circumstances, the firmware may fail to allocate a VSI for a VF.
When this happens, the driver does not react well to the bad news and
has a panic attack.

To fix this problem, check the return value from i40e_alloc_vf_res and
don't try to configure the device further if it failed. Additionally,
explicitly clear the INIT bit when we free VF resources, so that this
bit will be in the proper state in the failure case, and won't blow up
elsewhere.

Change-ID: I6a20ce2b59c3458fd832032e88fa28cd42500189
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This function call isn't needed here; the same function is already
called by i40e_reset_vf.

Change-ID: I96ccbf91b752965c9e28fe895d4c7d4c46e3ba44
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Changes the parsing of CEE App TLVs to fill in the App selector in struct
i40e_dcbx_config with the IEEE App selector so the caller doesn't have to
consider whether the App came from a CEE or IEEE DCBX negotiation.

Change-ID: Ia7d9d664cde04d2ebcc9822fd22e4929c6edab3a
Signed-off-by: NGreg Bowers <gregory.j.bowers@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a member to the nvm_info struct for oem_ver info to be
output either by OID or ethtool.

Change-ID: I1e5d513ae67622e2af17042924fdb4b5d6d85366
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace one left over (1 << up) in the i40e_dcb.c file with the BIT()
macro.

Change-ID: I39492a400a2cee5ac566143a5b436cc478bea0db
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Flag the filter_mask parameter as __always_unused in the
ndo_bridge_getlink function.

Change-ID: Ifc1e99c7fb84bcbf81cf7b0ac891ad8ca956ffb2
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the new Port link status bit and rename the link status to function
link status.

Change-ID: I71289327ae62638ce967b6ad40114caf998b6dab
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To help users and developers know what compile options
and hardware features are enabled at compile time, print
VxLAN is available.

Change-ID: I3162f3b7678dc725a597f964217920eb218b480b
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF really doesn't care about the QOS handle but it will in the
future. Since the VF only uses TC0, send it that handle. On the VF
side, save the handle and use it to populate the QOS params when we call
into the client interface.

Change-ID: I76f41b070baeaa09b19383e9168bc677837e0761
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I found a code indent that was avoidable because a whole function is inside
an if block, reverse the if and move the code back a tab.

Change-ID: I9989c8750ee61678fbf96a3b0fd7bf7cc7ef300a
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.

Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Changes parsing of AQ command Get CEE DCBX OPER CFG (0x0A07). Change is
required because FW creates the oper_prio_tc nibbles reversed from those
in the CEE Priority Group sub-TLV.

Change-ID: I7d9d8641bb430d30e286fc3fac909866ef8a0de8
Signed-off-by: NGreg Bowers <gregory.j.bowers@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ran into an issue where PF's VSI type list was different from VF's,
which was resulted in different enum index. The VSI type list can
be different depending on what build flag is used for PF and VF.

The change is to explicitly assign enum index for each VSI type
so that PF and VF always reference to the same VSI type event if the
enum lists are different.

Change-ID: I8c0e5fdb515f324f7964df863a458073cf467e57
Signed-off-by: NSerey Kong <serey.kong@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There's been some need for controlling the periodic link polling for
debugging link issues.  This patch enables switching it off and on
through an ethtool private flag.  The link poll remains on by default,
but can be turned off with
	ethtool --set-priv-flags p261p1 LinkPolling off
and later turned back on with
	ethtool --set-priv-flags p261p1 LinkPolling on

To check the current status, use
	ethtool --show-priv-flags p261p1

Change-ID: I32e4ab654ff3eec90a06cf144899971b82d71c40
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch addresses an issue where multiple link up messages can be logged
resulting from aq link status timing when link properties are changed (fc,
speed, etc.); solved by using a single function to handle status printing
and adding a mechanism to track whether link state (up or down) has
actually changed.

Change-ID: Ied6ed6e49dc397c77d992adc0bc9ed3767152b9d
Signed-off-by: NMatt Jared <matthew.a.jared@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where the PF's fdir filter table would have an
entry that the hw was unable to add. This notification happens in the hot
path, so instead of trying to fix it then, we note the location in the
failure case and delete it during regular fdir subtask callback. Without
this patch, a case can occur where an invalid entry gets replayed and a
valid one is not.

Change-ID: I67831c183b5d0309876de807cc434809b74c9cb7
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>