This patch prepares stmmac_err for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares the RX/TX DMA stop/start process for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares the DMA IRQ enable/disable process for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares DMA Operation Mode configuration for multiple queues.
The work consisted on breaking the DMA operation Mode configuration function
into RX and TX scope and adapting its mechanism in stmmac_main.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2017-03-15

This series contains updates to i40e and i40evf only.

Aaron fixes an issue on x710 devices where simultaneous read accesses
were interfering with each other, so make sure all devices acquire the
NVM lock before reads on all devices.

Shannon adds Wake On LAN support feature for x722 devices and cleaned
up the opcodes so that they are in numerical order.

Mitch adds a client interface to the VF driver, in preparation for the
upcoming RDMA-capable hardware (and client driver).  Cleaned up the
client interface in the PF driver, since it was originally over
engineered to handle multiple clients on multiple netdevs, but that
did not happen and now there will be one client per driver, so apply
the "KISS" (Keep It Simple & Stupid) to the i40e client interface.
Bumped the number of MAC filters an untrusted VF can create.

Jake fixes an issue where a recent refactor of queue pairs accidentally
added all remaining vecotrs to the num_lan_msix which can adversely
affect performance.

Lihong fixes an ethtool issue with x722 devices where "-e" will error
out since its EEPROM has a scope limit at offset 0x5B9FFF, so set the
EEPROM length to the scope limit.  Also fixed an issue where RSS
offloading only worked on PF0.

Filip cleans up and clarifies code comment so there is no confusion
about MAC/VLAN filter initialization routine.

Alex adds support for DMA_ATTR_SKIP_CPU_SYNC and DMA_ATTR_WEAK_ORDERING,
which improves performance on architectures that implement either one.

Harshitha cleans up confusion on flags disabled due to hardware limitation
versus featured disabled by the user, so rename auto_disable_flags to
hw_disabled_flags to avoid the confusion.

v2: Merged patch #1 and #4 in first version to make patch #3 in this
    series based on feedback from David Miller.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/broadcom/genet/bcmgenet.c
	net/core/sock.c

Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull SCSI fixes from James Bottomley:
 "This is a rather large set of fixes. The bulk are for lpfc correcting
  a lot of issues in the new NVME driver code which just went in in the
  merge window.

  The others are:

   - fix a hang in the vmware paravirt driver caused by incorrect
     handling of the new MSI vector allocation

   - long standing bug in storvsc, which recent block changes turned
     from being a harmless annoyance into a hang

   - yet more fallout (in mpt3sas) from the changes to device blocking

  The remainder are small fixes and updates"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (34 commits)
  scsi: lpfc: Add shutdown method for kexec
  scsi: storvsc: Workaround for virtual DVD SCSI version
  scsi: lpfc: revise version number to 11.2.0.10
  scsi: lpfc: code cleanups in NVME initiator discovery
  scsi: lpfc: code cleanups in NVME initiator base
  scsi: lpfc: correct rdp diag portnames
  scsi: lpfc: remove dead sli3 nvme code
  scsi: lpfc: correct double print
  scsi: lpfc: Rename LPFC_MAX_EQ_DELAY to LPFC_MAX_EQ_DELAY_EQID_CNT
  scsi: lpfc: Rework lpfc Kconfig for NVME options
  scsi: lpfc: add transport eh_timed_out reference
  scsi: lpfc: Fix eh_deadline setting for sli3 adapters.
  scsi: lpfc: add NVME exchange aborts
  scsi: lpfc: Fix nvme allocation bug on failed nvme_fc_register_localport
  scsi: lpfc: Fix IO submission if WQ is full
  scsi: lpfc: Fix NVME CMD IU byte swapped word 1 problem
  scsi: lpfc: Fix RCTL value on NVME LS request and response
  scsi: lpfc: Fix crash during Hardware error recovery on SLI3 adapters
  scsi: lpfc: fix missing spin_unlock on sql_list_lock
  scsi: lpfc: don't dereference dma_buf->iocbq before null check
  ...

Pull gfs2 fix from Bob Peterson:
 "This is an emergency patch for 4.11-rc3

  The GFS2 developers uncovered a really nasty problem that can lead to
  random corruption and kernel panic, much like the last one. Andreas
  Gruenbacher wrote a simple one-line patch to fix the problem."

* tag 'gfs2-4.11-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: Avoid alignment hole in struct lm_lockname

Pull crypto fixes from Herbert Xu:

 - self-test failure of crc32c on powerpc

 - regressions of ecb(aes) when used with xts/lrw in s5p-sss

 - a number of bugs in the omap RNG driver

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: s5p-sss - Fix spinlock recursion on LRW(AES)
  hwrng: omap - Do not access INTMASK_REG on EIP76
  hwrng: omap - use devm_clk_get() instead of of_clk_get()
  hwrng: omap - write registers after enabling the clock
  crypto: s5p-sss - Fix completing crypto request in IRQ handler
  crypto: powerpc - Fix initialisation of crc32c context

Commit 88ffbf3e switches to using rhashtables for glocks, hashing over
the entire struct lm_lockname instead of its individual fields.  On some
architectures, struct lm_lockname contains a hole of uninitialized
memory due to alignment rules, which now leads to incorrect hash values.
Get rid of that hole.
Signed-off-by: NAndreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: NBob Peterson <rpeterso@redhat.com>
CC: <stable@vger.kernel.org> #v4.3+

A previous commit introduced a field that tracks the features
that are disabled due to HW resource limitations as opposed
to the featured disabled by the user. This patch changes the
name of the field to make it more readable since it might get
confusing when looking at code containing both the flags
field and the auto_disable_features field together.

Change-ID: Idcc9888659698f6fe3ccff17c8c3f09b5026f708
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Our original filter limit of 8 was based on behavior that we saw from
Linux VMs. Now we're running Other Operating Systems under KVM and we
see that they commonly use more MAC filters. Since it seems weird to
require people to enable trusted VFs just to boot their OS, bump the
number of filters allowed by default.

Change-ID: I76b2dcb2ad6017e39231ad3096c3fb6f065eef5e
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING. By enabling both of these for the Rx path we
are able to see performance improvements on architectures that implement
either one due to the fact that page mapping and unmapping only has to
sync what is actually being used instead of the entire buffer. In addition
by enabling the weak ordering attribute enables a performance improvement
for architectures that can associate a memory ordering with a DMA buffer
such as Sparc.

Change-ID: If176824e8231c5b24b8a5d55b339a6026738fc75
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch clarifies the reason for removal of automatically
firmware-generated filter and explicit addition of filter which
accepts frames with any VLAN id.

Change-ID: Iabf180b6d61c4d8a36d3bcf8457c377a6f2aca0e
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the issue that RSS offloading only works on PF0 by
using the direct register writing of the hash keys for the VFs instead
of using the admin queue command to do so.

Change-ID: Ia02cda7dbaa23def342e8786097a2c03db6f580b
Signed-off-by: NLihong Yang <lihong.yang@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently ethtool -e will error out with a X722 interface
as its EEPROM has a scope limit at offset 0x5B9FFF.
This patch fixes the issue by setting the EEPROM length to
the scope limit to avoid NVM read failure beyond that.

Change-ID: I0b7d4dd6c7f2a57cace438af5dffa0f44c229372
Signed-off-by: NLihong Yang <lihong.yang@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a solution to avoid adding too many queues to num_lan_msix.
A recent refactor of queue pairs accidentally added all remaining
vectors to the num_lan_msix which can have adverse performance issues,
due to enabling more queues than the number of CPU cores.

This patch removes the old calculation, and replaces it with a simple
algorithm.

1) add queue pairs up to num_online_cpus(), but capped at half of total
   vectors
2) then add alternative features such as flow directory and similar
3) finally, add the remaining vectors back to queue pairs, but capped
   such that the total number of queue pairs does not exceed
   num_online_cpus().

Change-ID: I668abf67d5011a1248866daba8885f4ff00cb8d9
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

(KISS is Keep It Simple, Stupid. Or is it?)

The client interface vastly overengineered for what it needs to do.
It was originally designed to support multiple clients on multiple
netdevs, possibly even with multiple drivers. None of this happened,
and now we know that there will only ever be one client for i40e
(i40iw) and one for i40evf (i40iwvf). So, time for some KISS. Since
i40e and i40evf are a Dynasty, we'll simplify this one to match the
VF interface.

First, be a Destroyer and remove all of the lists and locks required
to support multiple clients. Keep one static around to keep track of
one client, and track the client instances for each netdev in the
driver's pf (or adapter) struct. Now it's Almost Human.

Since we already know the client type is iWarp, get rid of any checks
for this. Same for VSI type - it's always going to be the same type,
so it's just a Parasite.

While we're at it, fix up some comments. This makes the function
headers actually match the functions.

These changes reduce code complexity, simplify maintenance,
squash some lurking timing bugs, and allow us to Rock and Roll All
Nite.

Change-ID: I1ea79948ad73b8685272451440a34507f9a9012e
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In preparation for upcoming RDMA-capable hardware, add a client
interface to the VF driver. This is a slightly-simplified version
of the PF client interface, with the names changed to protect the
innocent.

Due to the nature of the VF<->PF interactions, the client interface
sometimes needs to call back into itself to pass messages. Because
of this, we can't use the coarse-grained locking like the PF's
client interface uses. Instead, we handle all client interactions
in a separate thread so the watchdog can still run and process
virtual channel messages.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull networking fixes from David Miller:

 1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
    from Steffen Klassert.

 2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
    Alexei Starovoitov.

 3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
    Michal Schmidt.

 4) We can get a divide by zero when TCP socket are morphed into
    listening state, fix from Eric Dumazet.

 5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
    skb_complete_tx_timestamp(). From Eric Dumazet.

 6) Use after free in dccp_feat_activate_values(), also from Eric
    Dumazet.

 7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
    Jarod Wilson.

 8) Fix use after free in vrf_xmit(), from David Ahern.

 9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
    Alexey Kodanev.

10) Properly check napi_complete_done() return value in order to decide
    whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
    Lendacky.

11) Fix double free of hwmon device in marvell phy driver, from Andrew
    Lunn.

12) Don't crash on malformed netlink attributes in act_connmark, from
    Etienne Noss.

13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
    from Sabrina Dubroca.

14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
    Florian Westphal.

15) Fix routing redirect races in dccp and tcp, basically the ICMP
    handler can't modify the socket's cached route in it's locked by the
    user at this moment. From Jon Maxwell.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
  qed: Enable iSCSI Out-of-Order
  qed: Correct out-of-bound access in OOO history
  qed: Fix interrupt flags on Rx LL2
  qed: Free previous connections when releasing iSCSI
  qed: Fix mapping leak on LL2 rx flow
  qed: Prevent creation of too-big u32-chains
  qed: Align CIDs according to DORQ requirement
  mlxsw: reg: Fix SPVMLR max record count
  mlxsw: reg: Fix SPVM max record count
  net: Resend IGMP memberships upon peer notification.
  dccp: fix memory leak during tear-down of unsuccessful connection request
  tun: fix premature POLLOUT notification on tun devices
  dccp/tcp: fix routing redirect race
  ucc/hdlc: fix two little issue
  vxlan: fix ovs support
  net: use net->count to check whether a netns is alive or not
  bridge: drop netfilter fake rtable unconditionally
  ipv6: avoid write to a possibly cloned skb
  net: wimax/i2400m: fix NULL-deref at probe
  isdn/gigaset: fix NULL-deref at probe
  ...

Some opcodes added & reordered to be in numerical order with the
rest of the opcodes.
This patch adds admin queue structs to support Wake on LAN feature
for X722.
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Acquire NVM lock before reads on all devices.  Previously, locks were
only used for X722 and later.  Fixes an issue where simultaneous X710
NVM accesses were interfering with each other.

Change-ID: If570bb7acf958cef58725ec2a2011cead6f80638
Signed-off-by: NAaron Salter <aaron.k.salter@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull cgroup fixes from Tejun Heo:
 "Three cgroup fixes.  Nothing critical:

   - the pids controller could trigger suspicious RCU warning
     spuriously. Fixed.

   - in the debug controller, %p -> %pK to protect kernel pointer
     from getting exposed.

   - documentation formatting fix"

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroups: censor kernel pointer in debug files
  cgroup/pids: remove spurious suspicious RCU usage warning
  cgroup: Fix indenting in PID controller documentation

Pull libata fixes from Tejun Heo:
 "Three libata fixes:

   - fix for a circular reference bug in sysfs code which prevented
     pata_legacy devices from being released after probe failure, which
     in turn prevented devres from releasing the associated resources.

   - drop spurious WARN in the command issue path which can be triggered
     by a legitimate passthrough command.

   - an ahci_qoriq specific fix"

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: qoriq: correct the sata ecc setting error
  libata: drop WARN from protocol error in ata_sff_qc_issue()
  libata: transport: Remove circular dependency at free time

Pull workqueue fix from Tejun Heo:
 "If a delayed work is queued with NULL @wq, workqueue code explodes
  after the timer expires at which point it's difficult to tell who the
  culprit was.

  This actually happened and the offender was net/smc this time.

  Add an explicit sanity check for it in the queueing path"

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: trigger WARN if queue_delayed_work() is called with NULL @wq

Pull percpu fixes from Tejun Heo:

 - the allocation path was updating pcpu_nr_empty_pop_pages without the
   required locking which can lead to incorrect handling of empty chunks
   (e.g. keeping too many around), which is buggy but shouldn't lead to
   critical failures. Fixed by adding the locking

 - a trivial patch to drop an unused param from pcpu_get_pages()

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: remove unused chunk_alloc parameter from pcpu_get_pages()
  percpu: acquire pcpu_lock when updating pcpu_nr_empty_pop_pages

This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.

It also adds 2 new PCI device-IDs to qede:
  - 0x8070 for QL41xxx PFs
  - 0x8090 for VFs spawning from QL41xxx PFs
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: Fixes series

This address several different issues in qed.
The more significant portions:

Patch #1 would cause timeout when qedr utilizes the highest
CIDs availble for it [or when future qede adapters would utilize
queues in some constellations].

Patch #4 fixes a leak of mapped addresses; When iommu is enabled,
offloaded storage protocols might eventually run out of resources
and fail to map additional buffers.

Patches #6,#7 were missing in the initial iSCSI infrastructure
submissions, and would hamper qedi's stability when it reaches
out-of-order scenarios.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.

Fixes: fc831825 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.

Fixes: 1d6cff4f ("qed: Add iSCSI out of order packet handling")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.

Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.

Fixes: 0a7fb11c ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: fc831825 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.

Fixes: 0a7fb11c ("qed: Add Light L2 support");
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.

Fixes: a91eb52a ("qed: Revisit chain implementation")
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.

Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.

Fixes: dbb799c3 ("qed: Initialize hardware for new protocols")
Signed-off-by: NRam Amrani <Ram.Amrani@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Couple of fixes

Couple or small fixes.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.

Fixes: a4feea74 ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.

Fixes: b2e345f9 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we notify peers of potential changes,  it's also good to update
IGMP memberships.  For example, during VM migration, updating IGMP
memberships will redirect existing multicast streams to the VM at the
new location.
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>