Add a read/write semaphore around the ops function pointers so
ops can be set to null when the driver un-registers.

Previously the tpm core expected module locking to be enough to
ensure that tpm_unregister could not be called during certain times,
however that hasn't been sufficient for a long time.

Introduce a read/write semaphore around 'ops' so the core can set
it to null when unregistering. This provides a strong fence around
the driver callbacks, guaranteeing to the driver that no callbacks
are running or will run again.

For now the ops_lock is placed very high in the call stack, it could
be pushed down and made more granular in future if necessary.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Now that we have a proper struct device just use dev_name() to
access this value instead of keeping two copies.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

This is a hold over from before the struct device conversion.

- All prints should be using &chip->dev, which is the Linux
  standard. This changes prints to use tpm0 as the device name,
  not the PnP/etc ID.
- The few places involving sysfs/modules that really do need the
  parent just use chip->dev.parent instead
- We no longer need to get_device(pdev) in any places since it is no
  longer used by any of the code. The kref on the parent is held
  by the device core during device_add and dropped in device_del
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Simplify st33zp24_spi_acpi_request_resources, st33zp24_spi_of_request_resources
and st33zp24_spi_request_resources to have the same prototype and using
spi_get_drvdata.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Simplify st33zp24_i2c_acpi_request_resources, st33zp24_i2c_of_request_resources
and st33zp24_i2c_request_resources to have the same prototype and using
i2c_get_clientdata.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add support for acpi probing. SMO3324 is used for st33zp24.
It has been tested with the following acpi node on Minnowboard:

Device (TPM1)
{
	Name (_ADR, Zero)  // _ADR: Address
	Name (_HID, "SMO3324")  // _HID: Hardware ID
	Name (_CID, "SMO3324")  // _CID: Compatible ID
	Name (_DDN, "SMO TPM")  // _DDN: DOS Device Name
	Name (_UID, One)  // _UID: Unique ID
	Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
	{
		Name (SBUF, ResourceTemplate ()
		{
			SpiSerialBus (0, PolarityLow, FourWireMode, 8,
				      ControllerInitiated, 4000000, ClockPolarityLow,
				      ClockPhaseFirst, "\\_SB.SPI1",
				      0x00, ResourceConsumer, ,)
			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
				 "\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0001
			}
			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
				"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0002,
			}
		})
		Return (SBUF) /* \_SB_.SPI1.TPM1._CRS.SBUF */
	}
	Method (_STA, 0, NotSerialized)  // _STA: Status
	{
		Return (0x0F)
	}
}
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add support for acpi probing. SMO3324 is used for st33zp24.
It has been tested with the following acpi node on Minnowboard:

Device (TPM1)
{
	Name (_ADR, Zero)  // _ADR: Address
	Name (_HID, "SMO3324")  // _HID: Hardware ID
	Name (_CID, "SMO3324")  // _CID: Compatible ID
	Name (_DDN, "SMO TPM")  // _DDN: DOS Device Name
	Name (_UID, One)  // _UID: Unique ID
	Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
	{
		Name (SBUF, ResourceTemplate ()
		{
			I2cSerialBus (0x0013, ControllerInitiated, 400000,
				      AddressingMode7Bit, "\\_SB.I2C7",
				      0x00, ResourceConsumer, ,)
			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
				 "\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{   	// Pin list
				0x0001
			}
			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
				"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{	// Pin list
				0x0002,
			}
		})
		Return (SBUF) /* \_SB_.I2C7.TPM1._CRS.SBUF */
	}

	Method (_STA, 0, NotSerialized)  // _STA: Status
	{
		Return (0x0F)
	}
}
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Extend copyright header to 2016
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add check in st33zp24_spi_evaluate_latency helping to diagnose if the chip
is present or in a bad state.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

DT headers already define NOOP routines when CONFIG_OF is not defined.

[jarkko.sakkinen@linux.intel.com: I tested that the driver compiles
 without warnings and errors with and without CONFIG_OF flag.]
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Remove spi_xfer from st33zp24_spi_phy structure and declare local spi_xfer
when needed instead.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

An affectation is enough when copying 1 byte. Remove memcpy usage where
possible.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Make sure every function name use st33zp24_spi_ prefix.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

nbr_dummy_bytes variable could be easily replaced by phy->latency in
st33zp24_spi_send and st33zp24_spi_recv.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Simplify st33zp24_spi_acpi_request_resources, st33zp24_spi_of_request_resources
and st33zp24_spi_request_resources to have the same prototype and using
spi_get_drvdata.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Simplify st33zp24_i2c_acpi_request_resources, st33zp24_i2c_of_request_resources
and st33zp24_i2c_request_resources to have the same prototype and using
i2c_get_clientdata.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add support for acpi probing. SMO3324 is used for st33zp24.
It has been tested with the following acpi node on Minnowboard:

Device (TPM1)
{
	Name (_ADR, Zero)  // _ADR: Address
	Name (_HID, "SMO3324")  // _HID: Hardware ID
	Name (_CID, "SMO3324")  // _CID: Compatible ID
	Name (_DDN, "SMO TPM")  // _DDN: DOS Device Name
	Name (_UID, One)  // _UID: Unique ID
	Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
	{
		Name (SBUF, ResourceTemplate ()
		{
			SpiSerialBus (0, PolarityLow, FourWireMode, 8,
				      ControllerInitiated, 4000000, ClockPolarityLow,
				      ClockPhaseFirst, "\\_SB.SPI1",
				      0x00, ResourceConsumer, ,)
			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
				 "\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0001
			}
			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
				"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0002,
			}
		})
		Return (SBUF) /* \_SB_.SPI1.TPM1._CRS.SBUF */
	}
	Method (_STA, 0, NotSerialized)  // _STA: Status
	{
		Return (0x0F)
	}
}
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add support for acpi probing. SMO3324 is used for st33zp24.
It has been tested with the following acpi node on Minnowboard:

Device (TPM1)
{
	Name (_ADR, Zero)  // _ADR: Address
	Name (_HID, "SMO3324")  // _HID: Hardware ID
	Name (_CID, "SMO3324")  // _CID: Compatible ID
	Name (_DDN, "SMO TPM")  // _DDN: DOS Device Name
	Name (_UID, One)  // _UID: Unique ID
	Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
	{
		Name (SBUF, ResourceTemplate ()
		{
			I2cSerialBus (0x0013, ControllerInitiated, 400000,
				      AddressingMode7Bit, "\\_SB.I2C7",
				      0x00, ResourceConsumer, ,)
			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
				 "\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{   	// Pin list
				0x0001
			}
			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
				"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{	// Pin list
				0x0002,
			}
		})
		Return (SBUF) /* \_SB_.I2C7.TPM1._CRS.SBUF */
	}

	Method (_STA, 0, NotSerialized)  // _STA: Status
	{
		Return (0x0F)
	}
}
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Extend copyright header to 2016
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add check in st33zp24_spi_evaluate_latency helping to diagnose if the chip
is present or in a bad state.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The core st33zp24 module is useless without either the I2C or the
SPI access module. So hide NFC_ST_NCI and select it automatically
if either TCG_TIS_ST33ZP24_I2C or TCG_TIS_ST33ZP24_SPI is selected.

This avoids presenting TCG_TIS_ST33ZP24 when neither TCG_TIS_ST33ZP24_I2C
nor TCG_TIS_ST33ZP24_SPI can be selected.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

DT headers already define NOOP routines when CONFIG_OF is not defined.

[jarkko.sakkinen@linux.intel.com: I tested that the driver compiles
 without warnings and errors with and without CONFIG_OF flag.]
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Remove spi_xfer from st33zp24_spi_phy structure and declare local spi_xfer
when needed instead.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

An affectation is enough when copying 1 byte. Remove memcpy usage where
possible.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Make sure every function name use st33zp24_spi_ prefix.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

nbr_dummy_bytes variable could be easily replaced by phy->latency in
st33zp24_spi_send and st33zp24_spi_recv.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: user-mode-linux-devel@lists.sourceforge.net

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: linux-s390@vger.kernel.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org

Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org

This moves seccomp after ptrace on x86 to that seccomp can catch changes
made by ptrace. Emulation should skip the rest of processing too.

We can get rid of test_thread_flag because there's no longer any
opportunity for seccomp to mess with ptrace state before invoking
ptrace.
Suggested-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: x86@kernel.org
Cc: Andy Lutomirski <luto@kernel.org>

When RET_TRACE triggers, a tracer may change a syscall into something that
should be filtered by seccomp. This re-runs seccomp after a trace event
to make sure things continue to pass.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@kernel.org>

Since nothing is using the 2-phase API, and it adds more complexity than
benefit, remove it.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@kernel.org>

I added two-phase syscall entry work back when the entry slow path
was very slow.  Nowadays, the entry slow path is fast and two-phase
entry work serves no purpose.  Remove it.
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NKees Cook <keescook@chromium.org>

Currently, if arch code wants to supply seccomp_data directly to
seccomp (which is generally much faster than having seccomp do it
using the syscall_get_xyz() API), it has to use the two-phase
seccomp hooks. Add it to the easy hooks, too.

Cc: linux-arch@vger.kernel.org
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NKees Cook <keescook@chromium.org>

One problem with seccomp was that ptrace could be used to change a
syscall after seccomp filtering had completed. This was a well documented
limitation, and it was recommended to block ptrace when defining a filter
to avoid this problem. This can be quite a limitation for containers or
other places where ptrace is desired even under seccomp filters.

This adds tests for both SECCOMP_RET_TRACE and PTRACE_SYSCALL manipulations.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@kernel.org>