Don't attempt to send a logout ORB if the target was already unplugged
or had its link switched off.  If two targets are attached, this
enhances the chance to quickly reconnect to the remaining target when
one target is plugged out.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NJarod Wilson <jwilson@redhat.com>

SBP2_MAX_SECTORS is nowhere used in fw-sbp2.
It merely got copied over from sbp2 where it played a role in the past.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This somewhat reduces the size of firewire-sbp2.ko.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes.  I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.

The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev.  (basically all inquiries it
issues can now be directly mapped).
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Since patch "fw-sbp2: use an own workqueue (fix system responsiveness)"
increased parallelism between fw-sbp2 and fw-core, it was possible that
fw-sbp2 didn't release the SCSI device when the FireWire device was
disconnected.

This happened if sbp2_update() ran during sbp2_login(), because a bus
reset occurred during sbp2_login().  The sbp2_login() work would [try
to] reschedule itself because it failed due to the bus reset, and it
would _not_ drop its reference on the target.  However, sbp2_update()
would schedule sbp2_login() too before sbp2_login() rescheduled itself
and hence sbp2_update() would take an additional reference.  And then
we would have one reference too many.

The fix is to _always_ drop the reference when leaving the sbp2_login()
work.  If the sbp2_login() work reschedules itself, it takes a
reference, but only if it wasn't already rescheduled by sbp2_update().

Ditto in the sbp2_reconnect() work.

The resulting code is actually simpler than before:  We _always_ take
a reference when successfully scheduling work.  And we _always_ drop
a reference when leaving a workqueue job.  No exceptions.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Firewire-sbp2 did very uncooperative things in the kernel's shared
workqueue:  Sleeping until reception of management status from the
target for up to 2 seconds, and performing SCSI inquiry and all of the
setup of SCSI command set drivers via scsi_add_device.  If there were
transient or permanent error conditions, this caused long blockage of
the kernel's events process, noticeable e.g. by blocked keyboard input.

We now allocate a workqueue process exclusive to fw-sbp2.  As a side
effect, this also increases parallelism of fw-sbp2's login and reconnect
work versus fw-core's device discovery and device update work which is
performed in the shared workqueue.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

On rare occasions, the ability to set one of the workaround flags at
runtime may save the day.

People who experience I/O errors with firewire-sbp2 while the old sbp2
driver worked for them should try workarounds=1 and report to the devel
mailinglist whether that improves things.  Firewire-sbp2 defaults to the
SCSI stack's maximum transfer size per command, while sbp2 limits them
to 128 kBytes.  Flag 1 accomplishes just that.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Fixes "New firewire stack only recognizing half of a chain of drives",
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242254Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

On IOMMU-less noncoherent architectures, orb->callback will memcpy the
whole SCSI command buffer for READ-like SCSI commands.  It is therefore
friendlier to enable IRQs before the call, like before patch "Add
ref-counting for sbp2 orbs".
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

This handles the case where we get the status write before getting the
complete_transaction callback ("status write for unknown orb").  In
this case, we just assume that the initial orb pointer transaction
succeeded and finish the orb.  To prevent the transaction callback
from touching freed memory, we ref-count the orb structures.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

As far as I know, all CardBus FireWire 400 adapters have a maximum
payload of 1024 bytes which is less than the speed-dependent limit of
2048 bytes.  Fw-sbp2 has to take the host adapter's limit into account.

This apparently fixes Juju's incompatibility with my CardBus cards, a
NEC based card and a VIA based card.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NKristian Høgsberg <krh@redhat.com>

collapsed with fw-sbp2 patch "Drop cast to non-const char * in host
template initialization." from Kristian Høgsberg
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

  - The CPU must not touch the buffer after it was DMA-mapped.
  - The size argument of dma_unmap_single(...page_table...) was bogus.
  - Move a comment closer to the code to which it refers to.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Add rudimentary check for the case that the page table overflows due to
merging of s/g elements by the IOMMU.  This would have lead to
overwriting of arbitrary memory.

After this change I expect that an offending command will be
unsuccessfully retried until the scsi_device is taken offline by SCSI
core.  It's a border case and not worth to implement a recovery
strategy.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

This is required per SBP-2 clause 5.2.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

noticed by Jay Fenlason
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Replace a cast with a container_of().  As long as nobody reorders the
structure elements, they do the same thing, but container_of() is more
readable.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added complete_command_orb)
Acked-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This affects of course only the "soft shutdown" case, e.g. "modprobe -r
firewire-sbp2", while it doesn't matter for hot unplug.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This currently only affects one bridge in the hardwired blacklist.
I don't own one of those, hence haven't tested it.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Use a speed probe to determine the speed over 1394b buses and of nodes
which report a link speed less than their PHY speed.

Log the effective maximum speed of newly created nodes in dmesg.

Also, read the config ROM (except bus info block) at the maximum speed
rather than S100.  This isn't a real optimization though because we
still only use quadlet read requests for the entire ROM.

The patch also adds support for S1600 and S3200, although such hardware
does not exist yet.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Also remove some errno printouts which will be shown by infrastructure
code anyway.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

cleanup after support of single-buffer requests was dropped
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>

The attribute /sys/bus/scsi/devices/*:*:*:*/ieee1394_id, as generated by
the old sbp2 driver, is typically used to create persistently named
links in /dev/disk/by-id.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The SCSI layer only passes sg requests down, so drop the
use_sg == 0, request_bufflen != 0 case.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This should be the last missing checks.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Avoids an extra allocation and simplifies lifetime rules for the scsi_host.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This patch loads fw-sbp2 if sbp2 is still in the config file. So one can
go back and forth between releases without worry about the root
filesystem drivers.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>

Existing mkinitrd scripts still have to be adapted, unless they grok
module aliases.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Drop filenames from file preamble, drop editor annotations and
use standard indent style for block comments.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (fixed typo)

Signed-off-by: NKristian Høgsberg <krh@redhat.com>

(Reverted part which moved it from eh_abort_handler to eh_host_reset_handler)
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>