This patch modifies the pcs mode support for SGMII. Even though
SGMII does auto-negotiation with phy, it needs stmmac_init_phy and
stmmac_mdio_register function for initializing phy.
Signed-off-by: NByungho An <bh74.an@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using DT for mdiobus and ethernet-phy requires to know the PHY address, which
is hard to guess if you don't know it. This patch extends of_mdiobus_register
to scan mdiobus for PHYs if reg property of the corresponding node is not set.
This also allows to have phy nodes in SoC DT files where the reg property can
be overwritten in the board file later. To encourage people to finally set the
actual phy address, the mdiobus scan is noisier than required.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell mdio driver uses internal registers that can be clock gated on
some SoCs. This patch just adds optional clock handling, to allow to pass
and enable the corresponding clock.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By using module_spi_driver we can eliminate a few lines of boilerplate code.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two sections checked whether the current channel != the new channel
without ever setting the current channel variables.

1. net/mac802154/tx.c: Prevent set_channel() from getting called every
time a packet is sent.

2. net/mac802154/mib.c: Lock (pib_lock) accesses to current_channel and
current_page and make sure they are updated when the channel has been
changed.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the MRF24J40, link-layer acknowledgment request and retry must be
turned on explicitly for each packet.  Turn this on in the hardware based
on the FC_ACK_REQ bit being set in the packet.

Also, now that failure to receive an ACK will cause the hardware to report
failure of transmission, change the log level for this failure to debug
level.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hi Greg,

I'm unsure if you or Dave should take that one as it's for one a TTY
patch but also living under net/. So I'm uncertain and let you decide!

Thanks,
Mathias

-- >8 --
Subject: [PATCH] TTY: ircomm, use GFP_KERNEL in ircomm_open()

We're clearly running in non-atomic context as our only call site is
able to call wait_event_interruptible(). So we're safe to use GFP_KERNEL
here instead of GFP_ATOMIC.
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only call site of irda_connect_response() is irda_accept() -- a
function called from user context only. Therefore it has no need for
GFP_ATOMIC.
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

irda_create() is called from user context only, therefore has no need
for GFP_ATOMIC.
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pskb_may_pull() can change skb->head, so we must init iph/greh after
calling it.

Bug added in commit c5441932 (GRE: Refactor GRE tunneling code.)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In at86rf230_probe() lp was first set to dev->priv and a few lines later
dev->priv was set to lp again, without changing lp in between. The call
to ieee802154_unregister_device() before err_irq: was unreachable.
Signed-off-by: NSascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a feature is not supported by firmware no need to print an error message.
This surpresses the following harmless message on boot up and ethtool query.
enic: Error 1 devcmd 36
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for NULL before calling the following operations from "struct
ieee802154_mlme_ops": assoc_req, assoc_resp, disassoc_req, start_req,
and scan_req.

This fixes a current oops where those functions are called but not
implemented. It also updates the documentation to clarify that they
are now optional by design. If a call to an unimplemented function
is attempted, the kernel returns EOPNOTSUPP via netlink.

The following operations are still required: get_phy, get_pan_id,
get_short_addr, and get_dsn.

Note that the places where this patch changes the initialization
of "ret" should not affect the rest of the code since "ret" was
always set (again) before returning its value.
Signed-off-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It served no purpose: we never call it from anywhere in the stack
and the only driver that did implement it (fakehard) merely provided
a dummy value.

There is also considerable doubt whether it would make sense to
even attempt beacon processing at this level in the Linux kernel.
Signed-off-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that uids and gids are completely encapsulated in kuid_t
and kgid_t we no longer need to pass struct cred which allowed
us to test both the uid and the user namespace for equality.

Passing struct cred potentially allows us to pass the entire group
list as BSD does but I don't believe the cost of cache line misses
justifies retaining code for a future potential application.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/nfc/microread/mei.c
	net/netfilter/nfnetlink_queue_core.c

Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check KR2 recovery time at the beginning of the work-around function.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Octeon SMI/MDIO interfaces can do clause 45 communications, so
implement this in the driver.

Also fix some comment formatting to make it consistent and to comply
with the netdev style.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_queue_xmit() will return a positive value if the packet could not be
queued, often because the real network device (in our case the mac802154
wpan device) has its queue stopped.  lowpan_xmit() should handle the
positive return code (for the debug statement) and return that value to
the higher layer so the higher layer will retry sending the packet.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increase the buffer length from 10 to 300 packets. Consider that traffic on
mac802154 devices will often be 6LoWPAN, and a full-length (1280 octet)
IPv6 packet will fragment into 15 6LoWPAN fragments (because the MTU of
IEEE 802.15.4 is 127).  A 300-packet queue is really 20 full-length IPv6
packets.

With a queue length of 10, an entire IPv6 packet was unable to get queued
at one time, causing fragments to be dropped, and making reassembly
impossible.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use netif_stop_queue() and netif_wake_queue() to control the flow of
packets to mac802154 devices.  Since many IEEE 802.15.4 devices have no
output buffer, and since the mac802154 xmit() function is designed to
block, netif_stop_queue() is called after each packet.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When ops->xmit() fails, drop the packet. Devices which support hardware
ack and retry (which include all devices currently supported by mainline),
will automatically retry sending the packet (in the hardware) up to 3
times, per the 802.15.4 spec.  There is no need, and it is incorrect to
try to do it in mac802154.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(Resend with a better changelog)

garp_pdu_queue() should ways be called with this spin lock.
garp_uninit_applicant() only holds rtnl lock which is not
enough here.  A possible race can happen as garp_pdu_rcv()
is called in BH context:

	garp_pdu_rcv()
	  |->garp_pdu_parse_msg()
	    |->garp_pdu_parse_attr()
	      |-> garp_gid_event()

Found by code inspection.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Ward <david.ward@ll.mit.edu>
Cc: "Jorge Boncompte [DTI2]" <jorge@dti2.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a simple test case that probes the packet socket's
TPACKET_V1, TPACKET_V2 and TPACKET_V3 behavior regarding mmap(2)'ed
I/O for a small burst of 100 packets. The test currently runs for ...

  TPACKET_V1: RX_RING, TX_RING
  TPACKET_V2: RX_RING, TX_RING
  TPACKET_V3: RX_RING

... and will output on success:

  test: TPACKET_V1 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
  test: TPACKET_V1 with PACKET_TX_RING .................... 100 pkts (9600 bytes)
  test: TPACKET_V2 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
  test: TPACKET_V2 with PACKET_TX_RING .................... 100 pkts (9600 bytes)
  test: TPACKET_V3 with PACKET_RX_RING .................... 100 pkts (9600 bytes)
  OK. All tests passed

Reusable parts of psock_fanout.c have been put into a psock_lib.h
file for common usage. Test case successfully tested on x86_64.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update SCTP maintainers list.
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch bypasses vxlan encapsulation if the destination vxlan
endpoint is a local device.

Changes since v1: added missing check for vxlan_find_vni() failure
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When our getdcbx entry is called, DCB_CAP_DCBX_HOST should be advertized too.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added readable description for the DPDP and port sensing device capabilities.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>