Depending on the regulator version, the voltage table might be
different. Use version specific regulator tables in order to select
correct voltage table. For the following regulator versions different
voltage tables are now used:

  * TPS658623: Use correct voltage table for SM2
  * TPS658643: New voltage table for SM2

Both versions are in use on the Colibri T20 module. Make use of the
correct tables by requesting the correct SM2 voltage of 1.8V.

This change is not backward compatible since an old driver is not able
to correctly set that value. The value 1.8V is out of range for the old
driver and will refuse to probe the device. The regulator starts with
default settings and the driver shows appropriate error messages.

On Colibri T20, the old value used to work with TPS658623 since the
driver applied a wrong voltage table too. However, the TPS658643 used
on V1.2 devices uses yet another voltage table and those broke that
pseudo-compatibility. The regulator driver now has the correct voltage
table for both regulator versions and those the correct voltage can be
used in the device tree.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Reviewed-by: NThierry Reding <treding@nvidia.com>
Acked-by: NMark Brown <broonie@linaro.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

device_type is deprecated and the kernel doesn't require it in most
cases. The only exceptions for flat tree users are the "gianfar",
"ucc_geth" and "ibm,emac" bindings, and arguably that requirement could
be relaxed for ucc_geth and ibm,emac (that is a task for separate
patches though).

This patch removes references to device_type="network" from the binding
documentation where possible and removes the properties from ARM and
microblaze dts files. This patch does not modify the powerpc .dts files
since there are a much larger number of them affected and I think the
ucc_geth, ibm,emac and gianfar users should be addressed before clearing
out the references to reduce the chance of breakage.
Signed-off-by: NGrant Likely <grant.likely@linaro.org>
Acked-by: NMichal Simek <monstr@monstr.eu>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>

Enable pinctrl for Broadcom Capri (BCM281xx) SoCs.
Signed-off-by: NSherman Yin <syin@broadcom.com>
Reviewed-by: NChristian Daudt <bcm@fixthebug.org>
Reviewed-by: NMatt Porter <matt.porter@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The device_type property is deprecated for the flattened device tree and
the value "ethernet-phy" has never been defined as having a useful
meaning. Neither the kernel nor u-boot depend on it. It should never
have appeared in PHY bindings. This patch removes all references to
"ethernet-phy" as a device_type value from the documentation and the
.dts files.

This patch was generated mechanically with the following command and
then verified by looking at the diff.

sed -i '/"ethernet-phy"/d' `git grep -l '"ethernet-phy"'`
Signed-off-by: NGrant Likely <grant.likely@linaro.org>
Acked-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch updates the Armada 370/XP SATA node with the new compatible
string "marvell,armada-370-sata".
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NTejun Heo <tj@kernel.org>

The summary interrupt is #16 in the SPI space. Unfortunately,
when this device was translated from board files to DT we forgot
to subtract 16 from the interrupt number to translate it into a
SPI interrupt. Also, the register space is larger than 4k, increase
it appropriately so that the gpio driver doesn't try to access
registers outside of its mapping.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

add pin groups for USP0 only holding one of TX and RX frame sync. this
patch matches with the change in drivers/pinctrl/sirf.
Signed-off-by: NRongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: NBarry Song <Barry.Song@csr.com>

this patch adds lost usp1_uart_nostreamctrl pin group for atlas6, which
matches with the change in drivers/pinctrl/sirf/pinctrl-atlas6.c.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>

This patch adds lost minigpsrtc device node for prima2 and atlas6,
which is behind rtc-iobg and whose offset is 2000.
Signed-off-by: NXianglong Du <Xianglong.Du@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>

prima2 and atlas6 uses cpufreq_cpu0, here we put related clock, operation
points in dtsi.
Signed-off-by: NRongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>

some nodes missed bus_width, clocks and status properties, here we fix them
in prima2 and atlas6 dtsi.
Signed-off-by: NBin Shi <Bin.Shi@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>

This patch adds lost clocks property(index 42) for cphifbg node in prima2 and
atlas6 dtsi.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>

The irq data for rng module defined in hwmod data previously
missed the OMAP_INTC_START relative offset, so the interrupt
number is probably misconfigured during the DT node addition
adjusting for this OMAP_INTC_START. Interrupt #36 is associated
with a watchdog timer, so fix the rng module's interrupt to the
appropriate interrupt #52.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The pl330 dmac won't be added to the list of amba devices, as it doesn't have
a clock entry.
Add the clock.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>

Sets the appropriate L2-cache latencies for the SOCFPGA platform.
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>

This patch adds a label and #clock-cells property to device node of
max77686 PMIC to allow using it as a clock provider.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Specify the remaining input clocks (pll_ref, pll_in, and sclk_pcm_in)
for the AudioSS clock controller.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Acked-by: NMike Turquette <mturquette@linaro.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NTomasz Figa <t.figa@samsung.com>

Specify pll_ref, pll_in, sclk_audio, and sclk_pcm_in for the AudioSS
clock controller.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Acked-by: NMike Turquette <mturquette@linaro.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NTomasz Figa <t.figa@samsung.com>

The Cubietruck makes use of the first three i2c controllers found on the
Allwinner A20; i2c-0 is used internally for the PMIC, i2c-1 is exposed on
the board headers, and i2c-2 is used for DDC on the VGA connector. This
patch enables them in the device tree.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The omap3_pmx_core pinmux device in the device tree handles the system
controller module (SCM) PADCONFS fonction. Its control registers are
split in two distinct areas, with other SCM registers in-between. Those
other registers can't thus be requested by other drivers as the memory
region gets reserved by the pinmux driver.

Split the omap3_pmx_core device tree node in two for the two memory
regions. The second region address and size depends on the SoC model.

The change in omap3.dtsi fixes an "external abort on non-linefetch" when
doing

cat /sys/kernel/debug/pinctrl/.../pins

on a Nokia N900.

Note that the core2 padconf region is different for 3430 vs 3630,
and does not exist on 3517 as noted by Nishanth Menon <nm@ti.com>.
Reported-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-By: NSebastian Reichel <sre@debian.org>
Signed-off-by: NNishanth Menon <nm@ti.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 based on Nishant's patch]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable the DCP by default on both i.MX23 and i.MX28.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Add a minimal board dts file for EXYNOS4412 based FriendlyARM's
TINY4412 board. This patch including support peripherals like
UART, SD card on SDMMC2 port and GPIO connected LEDs.
Signed-off-by: NAlex Ling <kasimling@gmail.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Arndale Octa board is based on Exynos5420 SoC. This patch
adds the basic support required for booting it through DT.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The SIC is cascaded off the PIC, so specify this in the device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The BCM2835 SoC contains a DWC2 USB controller. Add this to the DT.

Set up the pin controller to fully enable the USB controller on the
Raspberry Pi. The GPIO setup works because the default output value for
GPIO 6 (LAN_RUN/n_reset) just happens to be 1, which enables the
USB/LAN chip.

Note that you'll need a U-Boot which enables power to the USB controller;
search for U-Boot patch "ARM: rpi_b: power on SDHCI and USB HW modules".
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds basic board support for APQ8074 Dragonboard
which belongs to the Snapdragon 800 family.
For now, just support a basic machine with device tree.
Signed-off-by: NRohit Vaswani <rvaswani@codeaurora.org>
Acked-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
[olof: Split off SoC and board support in separate patches]
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add the mmio architected timer node.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add the restart node so we can reboot the device.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add support for the Snapdragon 800 MSM8974 SoC, used on the Dragonboard
and others. Board support added in separate patch.
Signed-off-by: NRohit Vaswani <rvaswani@codeaurora.org>
Acked-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
[olof: split off SoC support in separate patch]
Signed-off-by: NOlof Johansson <olof@lixom.net>

This commit adds the two external clock outputs available on A20 to
its device tree. A dummy fixed factor clock is also added to serve as
the first input of the clock outputs, which according to AW's A20 user
manual, is the 24MHz oscillator divided by 750.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Device tree naming conventions state that node names should match
the nodes function. Change external low speed oscillator node name
to match.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch adds the clock output pin options on the A20.
The 2 pins can output a configurable clock to be used by
external modules. This is used on the CubieTruck, to supply
a 32768 Hz low power clock to the onboard Wifi+BT module.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Due to incorrect clock specified in MDMA0 node, using MDMA0 controller
could cause system failures, due to wrong clock being controlled. This
patch fixes this by specifying correct clock.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
[t.figa: Corrected commit message and description.]
Signed-off-by: NTomasz Figa <t.figa@samsung.com>

The chosen nodes are nowadays pretty useless, since they will be overriden by
the bootloader anyway.

We can thus safely remove them.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The aliases are shared across boards are really belong to the DTSI.
Move them there.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

mbus is the memory bus clock, and it is present on both sun5i and sun7i
machines. Its register layout is compatible with the mod0 one.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This commit adds all the mod0 clocks available on A20 to its device
tree. This list was created by looking at AW's code release.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>