This adds a device tree node for the U300 system controller
and remaps this dynamically instead of using hard-coded
virtual addresses. The board power set-up code is altered
to fetch a reference to the syscon using ampersand <&syscon>
notation. This way of passing a pointer to the syscon will
also be used by the clocks.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This registers the U300 FSMC flash controller from the
device tree, and defines the three partitions. Skip the
BBT scan as in the current platform data.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This probes the U300 dummy-spichip from the device tree
and adds the apropriate node to the tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This registers the PL022 PrimeCell from the U300 device
tree. We make a new copy of the platform data for the
device tree boot path, as the old platform data is in an
older file which will be going away.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds the COH 901 318 DMA controller to the U300
device tree. All devices now converted to device tree
so far will start to find their DMA channels.

Note that the U300 is not yet using the device tree
to obtain DMA channels, but this is a first step.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds DMA channel assignments to the MMC/SD-controller
and the two UARTs already in the U300 device tree, as we
have now defined a way to obtain DMA channels from the
device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds support for the U300 MMC/SD card slot from the device
tree boot. No other changes needed.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Now that we have enabled board power and the AB3100 regulators,
put the regulator data into the device tree and enable it so
we can start to tie regulators to devices. To begin with we're
only supplying the power to the board itself.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds the COH 901 331 RTC to the U300 device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds the COH 901 327 watchdog to the U300 device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds the two I2C busses to the device tree so these
probe properly.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This register the most basic peripherals and makes the
U300 boot to prompt from a device tree.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The 'samsung,vbus-gpio' was submitted before pinmux landed for
exynos5250 and uses the old-style gpio specifier.  Fix the two
exynos5250 boards that use it.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Trivial patch, adding the i2c Cypress trackpad used on Snow.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>

If a board isn't using twl4030, then dtc will complain about the missing
phandle (which is in twl4030.dtsi).  Move the phy declaration to the dts
files.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The bootloader configures the pins, but has pull bits
set without pull enable bits. While this is harmless,
and won't do anything, it seems to cause confusion at
least for me every time looking at the pin configuration.
Fix it for DT based boot.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add GPMC data node to AM33XX device tree file.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit d16fb25d (ARM: dts: OMAP4460: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP4460 OPP data in
arch/arm/mach-omap2/opp4xxx_data.c
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit 3027e267 (ARM: dts: OMAP36xx: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP36xx OPP data in
arch/arm/mach-omap2/opp3xxx_data.c
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit ff5c9059 (ARM: dts: OMAP3+: Correct gpio #interrupts-cells
property) updated the number of interrupt cells required for configuring
gpios as interrupts for other devices (such as ethernet controllers).
This update allowed the interrupt type (edge, level, etc) to be
configured via device-tree (as described in the
Documentation/devicetree/bindings/gpio/gpio-omap.txt).

This broke ethernet support on the OMAP4 SDP board that defines a gpio
as the ethernet IRQ because the interrupt type (level, edge, etc) was
not getting configured correctly. This board use the ks8851 ethernet
chip which has an active low interrupt. Fix this by defining the gpio
interrupt as active-low in the device-tree binding.

Please note that the OMAP4-VAR-SOM also uses the same ethernet
controller and it is expected it will have the same problem. So the
same fix is also applied to this board.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I fumbled when resolving a merge conflict on application of commit
765d012c (ARM: dts: exynos4210: Add basic dts file for universal_c210
board), and left out the dts source file. Here it is.
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds basic device tree sources for Universal C210 board.

Currently support includes:
- eMMC
- serial
- max8952 and max8998 voltage regulators.
- gpio-keys

More support will be added in further patches.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds device tree node for PWM block present on Exynos 4 SoCs.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add basic EC information to device tree, currently only describing the
keyboard and keymap.
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Now that we have i2c-arbitrator in place on bus 4 we can add the
sbs-battery driver.  Future devices will be added onto bus 4 once
drivers are in good shape.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

We need to use the i2c-arbitrator to talk to any of the devices on i2c
bus 4 on exynos5250-snow so that we don't confuse the embedded
controller (EC).  Add the i2c-arbitrator to the device tree.  As we
add future devices (keyboard, sbs, tps65090) we'll add them on top of
this.

The arbitrated bus is numbered 104 simply as a convenience to make it
easier for people poking around to guess that it might have something
to do with the physical bus 4.

The addition is split between the cros5250-common and the snow device
tree file since not all cros5250-class devices use arbitration.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Commit 800974ac ("ARM: dts: Add board dts file for ODROID-X") includes a node
to describe the board level properties for mshc controller. But the mshc
controller node was not added in the Exynos4x12 dtsi file which resulted
in the following warning when compiling the dtb files.

Warning (reg_format): "reg" property in /mshc@12550000/slot@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /mshc@12550000/slot@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /mshc@12550000/slot@0

Fix this by adding the mshc controller node for Exynos4x12 SoCs.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Tested-by: NDongjin Kim <tobetter@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This change makes the rtc on the exynos5250 and 5440 disabled by
default to match exynos4.

Ever since the common clock framework came in, exynos5250 boards
have dumped lots of warnings in the boot log. It turns out that
we don't see those on exynos4 since the rtc is disabled by default.
While we need to get to the bottom of the problems with the RTC,
it still makes sense to have the default state of the RTC on exynos
boards match.

For the record, warnings look like this:
  ------------[ cut here ]------------
  WARNING: at drivers/clk/clk.c:771 __clk_enable+0x34/0xb0()
  Modules linked in:
  [<80015bfc>] (unwind_backtrace+0x0/0xec) from [<804717f0>] (dump_stack+0x20/0x24)
  [<804717f0>] (dump_stack+0x20/0x24) from [<80023cd0>] (warn_slowpath_common+0x5c/0x7c)
  [<80023cd0>] (warn_slowpath_common+0x5c/0x7c) from [<80023d1c>] (warn_slowpath_null+0x2c/0x34)
  [<80023d1c>] (warn_slowpath_null+0x2c/0x34) from [<8035ddb0>] (__clk_enable+0x34/0xb0)
  [<8035ddb0>] (__clk_enable+0x34/0xb0) from [<8035de54>] (clk_enable+0x28/0x3c)
  [<8035de54>] (clk_enable+0x28/0x3c) from [<8031a160>] (s3c_rtc_probe+0xf4/0x434)
  [<8031a160>] (s3c_rtc_probe+0xf4/0x434) from [<8028e288>] (platform_drv_probe+0x24/0x28)
  [<8028e288>] (platform_drv_probe+0x24/0x28) from [<8028ce10>] (driver_probe_device+0xbc/0x22c)
  [<8028ce10>] (driver_probe_device+0xbc/0x22c) from [<8028cff8>] (__driver_attach+0x78/0x9c)
  [<8028cff8>] (__driver_attach+0x78/0x9c) from [<8028bdfc>] (bus_for_each_dev+0x64/0xac)
  [<8028bdfc>] (bus_for_each_dev+0x64/0xac) from [<8028c7e0>] (driver_attach+0x28/0x30)
  [<8028c7e0>] (driver_attach+0x28/0x30) from [<8028c43c>] (bus_add_driver+0xe0/0x234)
  [<8028c43c>] (bus_add_driver+0xe0/0x234) from [<8028d55c>] (driver_register+0xac/0x13c)
  [<8028d55c>] (driver_register+0xac/0x13c) from [<8028e4f4>] (platform_driver_register+0x54/0x68)
  [<8028e4f4>] (platform_driver_register+0x54/0x68) from [<8065c944>] (s3c_rtc_driver_init+0x14/0x1c)
  [<8065c944>] (s3c_rtc_driver_init+0x14/0x1c) from [<800086d8>] (do_one_initcall+0x60/0x138)
  [<800086d8>] (do_one_initcall+0x60/0x138) from [<80633a8c>] (kernel_init_freeable+0x108/0x1d0)
  [<80633a8c>] (kernel_init_freeable+0x108/0x1d0) from [<8046d2f8>] (kernel_init+0x1c/0xf4)
  [<8046d2f8>] (kernel_init+0x1c/0xf4) from [<8000e358>] (ret_from_fork+0x14/0x20)
  ---[ end trace 4bcdc801c868d73f ]---
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
CC: rob.herring@calxeda.com
CC: will.deacon@arm.com
CC: arnd@arndb.de

xenvm is based on mach-vexpress, move it to mach-virt.

Changes in v4:
- update the dts Makefile too.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: will.deacon@arm.com
CC: arnd@arndb.de
CC: rob.herring@calxeda.com

Add chip-id controller nodes for Exynos4 and Exynos5 SoCs.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Tested-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
[wenyou.yang@atmel.com: added spi nodes for the sam9263ek, sam9g20ek, sam9m10g45ek and sam9n12ek boards]
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
[wenyou.yang@atmel.com: add spi nodes for sam9260, sam9263, sam9g45 and sam9n12]
[wenyou.yang@atmel.com: remove spi property "cs-gpios" to the board dts files]
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The exynos combiner irqchip needs to find the parent interrupts
and needs to know their number, so add the missing properties
for exynos4 as they were already present for exynos5.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

"atmel,sama5ek" compatibility sting does not correspond to a
useful board configuration. This d34ek.dts is the only sama5d3
.dts file affected.
Reported-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add DMA resources to MCI nodes.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
[nicolas.ferre@atmel.com: correct 9g45, 9n12 dma phandle name]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add DMA resources to i2c nodes.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
[nicolas.ferre@atmel.com: correct 9n12 dma phandle name]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Moving to generic DMA DT binding involves to set #dma-cells to 2.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable m25p64 SPI flash support on da850-EVM. Also
add partition information of SPI flash.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>