This will support the new VLAN attribute in the iSCSI iface file.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to speed up error recovery due to SPQ failures.  The error flag will
expedite the recovery process by skipping the timeouts.
Signed-off-by: NJeffrey Huang <huangjw@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When bnx2x returns error on FCoE SPQ messages, generate an error
completion to bnx2fc immediately to speed up error recovery.  This
will eliminate length timeouts and spped up the reset of the device.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sync DMA descriptor before hitting the TX mailbox for weak memory model
CPUs.

There has been discussions several years ago about this.  Some believe
that writel() should guarantee ordering.  Others want explicit barriers
if necessary.  Today writel() does not have the ordering guarantee and
many other drivers use explicit barriers.
Signed-off-by: NVlad Zolotarov <vlad@scalemp.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the user to override the default number of RSS/TSS rings.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.

Remove the allocation failure messages.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add statistics for tracking parity errors from which we successfully
recovered and those which were deemed unrecoverable.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Sample mcp pulse and mcp sequence in nic load instead of in init_one
as they may change by the time we want to use them.

2. Allow cnic to access device during nic load (by adding a new "LOADING" state
to recovery flow). This prevents the unnecessary cnic timeout which resulted
by cnic attempting to access because nic is loading, but being blocked because
of the Recovery state.

3. Issue 'fake' driver load command to mcp when last driver unloads to prevent
mcp from taking ownership. When recovery is complete unload fake driver to
allow mcp to initialize the hardware before first driver loads.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recovery register (to which a hardware lock has been added in previous
patch) is used amongst other things to track the active PFs. The old
implementation which used a per path counter is not viable in a virtualized
environment where a pf may increment the counter and then have the kernel
crash around it preventing the counter from ever reaching zero.
In the new implementation the scenario described will result in the PF timing
out against the mcp, which will clear the PF's bit in the bitmask allowing
recovery process to proceed.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use hardware locks to protect resources common to several Physical Functions. In
a virtualized environment the RTNL lock only protects a PF's driver against
the PFs sharing it's VMs with regard to device resources. Other PFs may reside
in other VMs under other OSs, and are not subject to the lock. Such resources
which were previously protected implicitly by the RTNL lock must now be
protected explicitly with dedicated HW locks.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a virtualized environment it is possible for a loading driver to discover
that Firmware is already loaded to the device, and that this FW does not match
its own. This can happen for example if different Physical Functions are
Assigned to different VMs in which different driver versions are loaded. The
code in this patch ensures that only drivers with matching FW are loaded over
the device, and that in the case described above where the Firmware version
doesn't match the driver load is aborted.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Fix bug where return value is ignored
2. Improve printouts
3. Fix typos
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BDF was obtained from kernel but since in virtualized environment
(e.g. physical device assigment in KVM) the function number may
not be the real one, the info must be obtained from the device.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In virtualized environments indirect access to the device may not be supported
(depending on the Hypervisor type). Indirect device access was used since in
some harware contexts (i.e. certain chipset and BIOS) every access the driver
makes across the pci is followed by a BIOS initiated Zero Length Read to the
same address. When accessing widebus registers this zero length read corrupts
the serialization of the read/write sequence resulting with errors. To avoid
this problem widebus registers are always accessed via the DMAE or the indirect
interface. However, the 57712x and 578xx devices intercept the zero length read
and so using the indirect interface with these devices is not necessary. Since
PDA is only supported for 57712x and 578xx the indirect access to device was
restricted to 57710 and 57711x.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the use of up to three hardware queues for transmission. The queues
are always dequed round robin (i.e. strict priority, PFC and ETS are not
supported). This does allow the allocation of a seperate HW queue for low
volume, high priority traffic which will be serviced more promptly.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We introduced a new return here but forgot to drop the lock.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3_start_xmit() makes the wrong assumption for TSOV6 that skb->head
doesnt include any payload data.

if (skb_is_gso_v6(skb))
	hdr_len = skb_headlen(skb) - ETH_HLEN;

This is not true anymore after commit f07d960d (tcp: avoid frag
allocation for small frames)

We should instead use : skb_transport_offset(skb) + tcp_hdrlen(skb)

Its also true for IPv4
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macro `CHIP_IS_E1x' requires `bp' to be initialized.
As `bp' is not yet initialized during this phase of `bnx2x_init_dev',
it accessed uninitialized fields in the struct.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previosuly, in MF modes `ethtool -S' lacked some of the statistics
which appeared in non-MF modes. This has been fixed.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon insertion of elements into the execution queue, it is validated
that there are enough credits to support additional vlan-macs,
and the credits are consumed. However, when removing a pending
command in `bnx2x_vland_mac_del_all' the consumed credits are not
released, which might cause leakage and eventually the inability to
add new vlan-macs in certain scenarios.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled.  However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup.  When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.

This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt.  In such a configuration, the
device's multivector interrupt mode must be disabled.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable the work-around for the autoneg KR of the BCM57810 in case the Warpcore version is 0xD108 and above, which fixes this problem.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable the autoGrEEEn feature for BCM84833.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unsupported speed of 100Mb force for BCM84833 due to hardware
limitation.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch handles the second port of a path in a 4-port device of
BCM57840.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Super-Isolate mode comes to isolate the BCM84833 PHY from the
outside world.  Not doing it correctly, made link partner see the link
before the driver was loaded.

This patch also involves SPIROM version fixes since it is used to
determine whether the common init of the PHY was already executed, and
the common init of this PHY is partially responsible for setting the
Super-Isolate mode.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a bnx2x device encounters parity errors, it will not respond to all
SPQ messages.  As a result, the shutdown sequence before reset can take
a long time as the ulp drivers (bnx2i/bnx2fc) have to wait for timeout
of all such messages.

To improve this scenario, when bnx2x returns error on the SPQ, we'll send
an immediate response to the ulp drivers to avoid such lengthy timeouts.

Adjust the return code of relevant functions to return error only if
the message cannot be sent on the SPQ so that we'll generate an error
completion to the ulp drivers.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

because bnx2x frees the old and allocates new memory during chip reset.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DaveM said:
   Please, this kind of stuff rots forever and not using bool properly
   drives me crazy.

Joe Perches <joe@perches.com> gave me the spatch script:

	@@
	bool b;
	@@
	-b = 0
	+b = false
	@@
	bool b;
	@@
	-b = 1
	+b = true

I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the ethtool callbacks necessary to change the rss
indirection table from userspace.  Should the number of interrupts
change (e.g.  across a close / open call, or through a reset) and
any one of the indirection table values fall out-of-range, the driver
will reset the indirection table to a default layout.

[Integrated many suggestions made by Ben Hutchings.]

Changes since v3

* Removed TG3_FLAG_SUPPORT_MSIX checks at the start of
  tg3_get_rxfh_indir() and tg3_set_rxfh_indir().
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2-mips-06-6.2.3 and bnx2-mips-09-6.2.1.b

New firmware fixes iSCSI problems with some LeftHand targets that don't
set TTT=0xffffffff for Data-In according to spec.  Firmware generates
exception warnings for this condition and becomes very slow.  This is
fixed by suppressing these warnings when using default error mask.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All drivers that support modification of the RX flow hash indirection
table initialise it in the same way: RX rings are assigned to table
entries in rotation.  Make that default policy explicit by having them
call a ethtool_rxfh_indir_default() function.

In the ethtool core, add support for a zero size value for
ETHTOOL_SRXFHINDIR, which resets the table to this default.
Partly-suggested-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>