This patch addresses a couple of minor items, mostly addesssing
prandom_bytes(): 1) prandom_bytes{,_state}() should use size_t
for length arguments, 2) We can use put_unaligned() when filling
the array instead of open coding it [ perhaps some archs will
further benefit from their own arch specific implementation when
GCC cannot make up for it ], 3) Fix a typo, 4) Better use unsigned
int as type for getting the arch seed, 5) Make use of
prandom_u32_max() for timer slack.

Regarding the change to put_unaligned(), callers of prandom_bytes()
which internally invoke prandom_bytes_state(), don't bother as
they expect the array to be filled randomly and don't have any
control of the internal state what-so-ever (that's also why we
have periodic reseeding there, etc), so they really don't care.

Now for the direct callers of prandom_bytes_state(), which
are solely located in test cases for MTD devices, that is,
drivers/mtd/tests/{oobtest.c,pagetest.c,subpagetest.c}:

These tests basically fill a test write-vector through
prandom_bytes_state() with an a-priori defined seed each time
and write that to a MTD device. Later on, they set up a read-vector
and read back that blocks from the device. So in the verification
phase, the write-vector is being re-setup [ so same seed and
prandom_bytes_state() called ], and then memcmp()'ed against the
read-vector to check if the data is the same.

Akinobu, Lothar and I also tested this patch and it runs through
the 3 relevant MTD test cases w/o any errors on the nandsim device
(simulator for MTD devs) for x86_64, ppc64, ARM (i.MX28, i.MX53
and i.MX6):

  # modprobe nandsim first_id_byte=0x20 second_id_byte=0xac \
                     third_id_byte=0x00 fourth_id_byte=0x15
  # modprobe mtd_oobtest dev=0
  # modprobe mtd_pagetest dev=0
  # modprobe mtd_subpagetest dev=0

We also don't have any users depending directly on a particular
result of the PRNG (except the PRNG self-test itself), and that's
just fine as it e.g. allowed us easily to do things like upgrading
from taus88 to taus113.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Tested-by: NAkinobu Mita <akinobu.mita@gmail.com>
Tested-by: NLothar Waßmann <LW@KARO-electronics.de>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement GRO for UDPv6. Add UDP checksum verification in gro_receive
for both UDP4 and UDP6 calling skb_gro_checksum_validate_zero_check.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add inet_gro_compute_pseudo and ip6_gro_compute_pseudo. These are
the logical equivalents of inet_compute_pseudo and ip6_compute_pseudo
for GRO path. The IP header is taken from skb_gro_network_header.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add skb_gro_checksum_validate, skb_gro_checksum_validate_zero_check,
and skb_gro_checksum_simple_validate, and __skb_gro_checksum_complete.
These are the cognates of the normal checksum functions but are used
in the gro_receive path and operate on GRO related fields in sk_buffs.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers, and perhaps other entities we have not yet considered,
sometimes want to know how deep the protocol headers go before
deciding how large of an SKB to allocate and how much of the packet to
place into the linear SKB area.

For example, consider a driver which has a device which DMAs into
pools of pages and then tells the driver where the data went in the
DMA descriptor(s).  The driver can then build an SKB and reference
most of the data via SKB fragments (which are page/offset/length
triplets).

However at least some of the front of the packet should be placed into
the linear SKB area, which comes before the fragments, so that packet
processing can get at the headers efficiently.  The first thing each
protocol layer is going to do is a "pskb_may_pull()" so we might as
well aggregate as much of this as possible while we're building the
SKB in the driver.

Part of supporting this is that we don't have an SKB yet, so we want
to be able to let the flow dissector operate on a raw buffer in order
to compute the offset of the end of the headers.

So now we have a __skb_flow_dissect() which takes an explicit data
pointer and length.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 28nm Gigabit PHY on BCM7xxx chips comes out of reset with absolutely
no EEE capabilities, such that we would actually return that we do not
support EEE when accessing 3.20 (MDIO_PCS_EEE_ABLE) registers.

Poke through the vendor-specific C45 register to enable EEE globally at
the PHY level, and advertise supported EEE modes.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some PHY drivers might need to access Clause 45 registers in Clause 22
compatibility mode to e.g: properly advertise EEE support when disabled
by default.

Export these two helper functions: phy_read_mmd_indirect() and
phy_write_mmd_indirect() for drivers to use them.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The shadow register 0x1C is used both by the BCM54xxx PHYs and the
BCM7xxx internal PHYs, move the accessors to a common location so both
drivers can use them.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 439d39a9 ("net: phy: broadcom:
extract register definitions") added a bunch of registers to brcmphy.h
but left some to broadcom.c, move all of them to the header file since
the BCM54xx and BCM7xxx PHY drivers do share all of these registers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon timeout, undo (via both timestamps/Eifel and DSACKs) was
disabled if any retransmits were still in flight.  The concern was
perhaps that spurious retransmission sent in a previous recovery
episode may trigger DSACKs to falsely undo the current recovery.

However, this inadvertently misses undo opportunities (using either
TCP timestamps or DSACKs) when timeout occurs during a loss episode,
i.e.  recurring timeouts or timeout during fast recovery. In these
cases some retransmissions will be in flight but we should allow
undo. Furthermore, we should only reset undo_marker and undo_retrans
upon timeout if we are starting a new recovery episode. Finally,
when we do reset our undo state, we now do so in a manner similar
to tcp_enter_recovery(), so that we require a DSACK for each of
the outstsanding retransmissions. This will achieve the original
goal by requiring that we receive the same number of DSACKs as
retransmissions.

This patch increases the undo events by 50% on Google servers.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ktime_get_ns() replaces ktime_to_ns(ktime_get())

ktime_get_real_ns() replaces ktime_to_ns(ktime_get_real())
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Userspace needs to be notified if one changes some option.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NVeaceslav Falico <vfalico@gmail.com>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit da3c6647(I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI
config) adds a new kernel config I2C_ACPI and make I2C core built in
when the config is selected. This is wrong because distributions
etc generally compile I2C as a module and the commit broken that.
This patch is to rename I2C_ACPI to ACPI_I2C_OPREGION. New config
only controls ACPI I2C operation region code and depends on I2C=y.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
[wsa: removed unrelated change for Kconfig]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Commit 9183df25 ("shm: add memfd_create() syscall") added a new
system call (memfd_create) but didn't update the asm-generic unistd
header.

This patch adds the new system call to the asm-generic version of
unistd.h so that it can be used by architectures such as arm64.

Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.

Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@greenl8ke.davemloft.net>

Call rcu_deference_raw() directly from within rht_for_each_entry_rcu()
as list_for_each_entry_rcu() does.

Fixes the following sparse warnings:
net/netlink/af_netlink.c:2906:25:    expected struct rhash_head const *__mptr
net/netlink/af_netlink.c:2906:25:    got struct rhash_head [noderef] <asn:4>*<noident>

Fixes: e341694e ("netlink: Convert netlink_lookup() to use RCU protected hash table")
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to export rht_obj(), all inner to outer object translations
occur internally. It was intended to be used with rht_for_each() which
now primarily serves as the iterator for rhashtable_remove_pprev() to
effectively flush and free the full table.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Properly annotate next pointers as access is RCU protected in
the lookup path.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_tw_recycle heavily relies on tcp timestamps to build a per-host
ordering of incoming connections and teardowns without the need to
hold state on a specific quadruple for TCP_TIMEWAIT_LEN, but only for
the last measured RTO. To do so, we keep the last seen timestamp in a
per-host indexed data structure and verify if the incoming timestamp
in a connection request is strictly greater than the saved one during
last connection teardown. Thus we can verify later on that no old data
packets will be accepted by the new connection.

During moving a socket to time-wait state we already verify if timestamps
where seen on a connection. Only if that was the case we let the
time-wait socket expire after the RTO, otherwise normal TCP_TIMEWAIT_LEN
will be used. But we don't verify this on incoming SYN packets. If a
connection teardown was less than TCP_PAWS_MSL seconds in the past we
cannot guarantee to not accept data packets from an old connection if
no timestamps are present. We should drop this SYN packet. This patch
closes this loophole.

Please note, this patch does not make tcp_tw_recycle in any way more
usable but only adds another safety check:
Sporadic drops of SYN packets because of reordering in the network or
in the socket backlog queues can happen. Users behing NAT trying to
connect to a tcp_tw_recycle enabled server can get caught in blackholes
and their connection requests may regullary get dropped because hosts
behind an address translator don't have synchronized tcp timestamp clocks.
tcp_tw_recycle cannot work if peers don't have tcp timestamps enabled.

In general, use of tcp_tw_recycle is disadvised.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure we use the correct address-family-specific function for
handling MTU reductions from within tcp_release_cb().

Previously AF_INET6 sockets were incorrectly always using the IPv6
code path when sometimes they were handling IPv4 traffic and thus had
an IPv4 dst.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Diagnosed-by: NWillem de Bruijn <willemb@google.com>
Fixes: 563d34d0 ("tcp: dont drop MTU reduction indications")
Reviewed-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't know right timestamp for repaired skb-s. Wrong RTT estimations
isn't good, because some congestion modules heavily depends on it.

This patch adds the TCPCB_REPAIRED flag, which is included in
TCPCB_RETRANS.

Thanks to Eric for the advice how to fix this issue.

This patch fixes the warning:
[  879.562947] WARNING: CPU: 0 PID: 2825 at net/ipv4/tcp_input.c:3078 tcp_ack+0x11f5/0x1380()
[  879.567253] CPU: 0 PID: 2825 Comm: socket-tcpbuf-l Not tainted 3.16.0-next-20140811 #1
[  879.567829] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[  879.568177]  0000000000000000 00000000c532680c ffff880039643d00 ffffffff817aa2d2
[  879.568776]  0000000000000000 ffff880039643d38 ffffffff8109afbd ffff880039d6ba80
[  879.569386]  ffff88003a449800 000000002983d6bd 0000000000000000 000000002983d6bc
[  879.569982] Call Trace:
[  879.570264]  [<ffffffff817aa2d2>] dump_stack+0x4d/0x66
[  879.570599]  [<ffffffff8109afbd>] warn_slowpath_common+0x7d/0xa0
[  879.570935]  [<ffffffff8109b0ea>] warn_slowpath_null+0x1a/0x20
[  879.571292]  [<ffffffff816d0a05>] tcp_ack+0x11f5/0x1380
[  879.571614]  [<ffffffff816d10bd>] tcp_rcv_established+0x1ed/0x710
[  879.571958]  [<ffffffff816dc9da>] tcp_v4_do_rcv+0x10a/0x370
[  879.572315]  [<ffffffff81657459>] release_sock+0x89/0x1d0
[  879.572642]  [<ffffffff816c81a0>] do_tcp_setsockopt.isra.36+0x120/0x860
[  879.573000]  [<ffffffff8110a52e>] ? rcu_read_lock_held+0x6e/0x80
[  879.573352]  [<ffffffff816c8912>] tcp_setsockopt+0x32/0x40
[  879.573678]  [<ffffffff81654ac4>] sock_common_setsockopt+0x14/0x20
[  879.574031]  [<ffffffff816537b0>] SyS_setsockopt+0x80/0xf0
[  879.574393]  [<ffffffff817b40a9>] system_call_fastpath+0x16/0x1b
[  879.574730] ---[ end trace a17cbc38eb8c5c00 ]---

v2: moving setting of skb->when for repaired skb-s in tcp_write_xmit,
    where it's set for other skb-s.

Fixes: 431a9124 ("tcp: timestamp SYN+DATA messages")
Fixes: 740b0f18 ("tcp: switch rtt estimations to usec resolution")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrey Vagin <avagin@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add tracepoint to track hugepage invalidate. This help us
in debugging difficult to track bugs.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Platforms like IBM Power Systems supports service processor
assisted dump. It provides interface to add memory region to
be captured when system is crashed.

During initialization/running we can add kernel memory region
to be collected.

Presently we don't have a way to get the log buffer base address
and size. This patch adds support to return log buffer address
and size.
Signed-off-by: NVasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NAndrew Morton <akpm@linux-foundation.org>

added struct sockaddr_storage to rdma_user_cm.h without also adding an
include for linux/socket.h to make sure it is defined.  Systemtap
needs the header files to build standalone and cannot rely on other
files to pre-include other headers, so add linux/socket.h to the list
of includes in this file.

Fixes: ee7aed45 ("RDMA/ucma: Support querying for AF_IB addresses")
Signed-off-by: NDoug Ledford <dledford@redhat.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel.  When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets.  This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.

There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver.  These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb.  When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.

The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued.  The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0

This connection finally times out.

I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver.  There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.

The patch attempt to fix this another way.  It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core.  This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.

CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slot quirks "disable-wp" is deprecated.
Instead, use the host quirk "disable-wp".
(Because the slot-node is removed in dt-file.)
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NSachin Kamat <sachin.kamat@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Using the new registration mechanism, define a flag that indicates the
user wishes to process RMPP messages in user space rather than have
the kernel process them.
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Registrations options are specified through flags.  Definitions of flags will
be in subsequent patches.
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Pages allocated using the DMA API have a coherent memory mapping. Make
this mapping visible to drivers so they can decide to use it instead of
creating their own redundant one.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NDavid Airlie <airlied@linux.ie>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This is the final piece of the puzzle of verifying kernel image signature
during kexec_file_load() syscall.

This patch calls into PE file routines to verify signature of bzImage.  If
signature are valid, kexec_file_load() succeeds otherwise it fails.

Two new config options have been introduced.  First one is
CONFIG_KEXEC_VERIFY_SIG.  This option enforces that kernel has to be
validly signed otherwise kernel load will fail.  If this option is not
set, no signature verification will be done.  Only exception will be when
secureboot is enabled.  In that case signature verification should be
automatically enforced when secureboot is enabled.  But that will happen
when secureboot patches are merged.

Second config option is CONFIG_KEXEC_BZIMAGE_VERIFY_SIG.  This option
enables signature verification support on bzImage.  If this option is not
set and previous one is set, kernel image loading will fail because kernel
does not have support to verify signature of bzImage.

I tested these patches with both "pesign" and "sbsign" signed bzImages.

I used signing_key.priv key and signing_key.x509 cert for signing as
generated during kernel build process (if module signing is enabled).

Used following method to sign bzImage.

pesign
======
- Convert DER format cert to PEM format cert
openssl x509 -in signing_key.x509 -inform DER -out signing_key.x509.PEM -outform
PEM

- Generate a .p12 file from existing cert and private key file
openssl pkcs12 -export -out kernel-key.p12 -inkey signing_key.priv -in
signing_key.x509.PEM

- Import .p12 file into pesign db
pk12util -i /tmp/kernel-key.p12 -d /etc/pki/pesign

- Sign bzImage
pesign -i /boot/vmlinuz-3.16.0-rc3+ -o /boot/vmlinuz-3.16.0-rc3+.signed.pesign
-c "Glacier signing key - Magrathea" -s

sbsign
======
sbsign --key signing_key.priv --cert signing_key.x509.PEM --output
/boot/vmlinuz-3.16.0-rc3+.signed.sbsign /boot/vmlinuz-3.16.0-rc3+

Patch details:

Well all the hard work is done in previous patches.  Now bzImage loader
has just call into that code and verify whether bzImage signature are
valid or not.

Also create two config options.  First one is CONFIG_KEXEC_VERIFY_SIG.
This option enforces that kernel has to be validly signed otherwise kernel
load will fail.  If this option is not set, no signature verification will
be done.  Only exception will be when secureboot is enabled.  In that case
signature verification should be automatically enforced when secureboot is
enabled.  But that will happen when secureboot patches are merged.

Second config option is CONFIG_KEXEC_BZIMAGE_VERIFY_SIG.  This option
enables signature verification support on bzImage.  If this option is not
set and previous one is set, kernel image loading will fail because kernel
does not have support to verify signature of bzImage.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch does two things.  It passes EFI run time mappings to second
kernel in bootparams efi_info.  Second kernel parse this info and create
new mappings in second kernel.  That means mappings in first and second
kernel will be same.  This paves the way to enable EFI in kexec kernel.

This patch also prepares and passes EFI setup data through bootparams.
This contains bunch of information about various tables and their
addresses.

These information gathering and passing has been written along the lines
of what current kexec-tools is doing to make kexec work with UEFI.

[akpm@linux-foundation.org: s/get_efi/efi_get/g, per Matt]
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Matt Fleming <matt@console-pimps.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is loader specific code which can load bzImage and set it up for
64bit entry.  This does not take care of 32bit entry or real mode entry.

32bit mode entry can be implemented if somebody needs it.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Load purgatory code in RAM and relocate it based on the location.
Relocation code has been inspired by module relocation code and purgatory
relocation code in kexec-tools.

Also compute the checksums of loaded kexec segments and store them in
purgatory.

Arch independent code provides this functionality so that arch dependent
bootloaders can make use of it.

Helper functions are provided to get/set symbol values in purgatory which
are used by bootloaders later to set things like stack and entry point of
second kernel etc.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Previous patch provided the interface definition and this patch prvides
implementation of new syscall.

Previously segment list was prepared in user space.  Now user space just
passes kernel fd, initrd fd and command line and kernel will create a
segment list internally.

This patch contains generic part of the code.  Actual segment preparation
and loading is done by arch and image specific loader.  Which comes in
next patch.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the new syscall kexec_file_load() declaration/interface.  I have
reserved the syscall number only for x86_64 so far.  Other architectures
(including i386) can reserve syscall number when they enable the support
for this new syscall.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

So far kexec_segment->buf was always a user space pointer as user space
passed the array of kexec_segment structures and kernel copied it.

But with new system call, list of kexec segments will be prepared by
kernel and kexec_segment->buf will point to a kernel memory.

So while I was adding code where I made assumption that ->buf is pointing
to kernel memory, sparse started giving warning.

Make ->buf a union.  And where a user space pointer is expected, access it
using ->buf and where a kernel space pointer is expected, access it using
->kbuf.  That takes care of sparse warnings.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I have added two more functions to walk through resources.

Currently walk_system_ram_range() deals with pfn and /proc/iomem can
contain partial pages.  By dealing in pfn, callback function loses the
info that last page of a memory range is a partial page and not the full
page.  So I implemented walk_system_ram_res() which returns u64 values to
callback functions and now it properly return start and end address.

walk_system_ram_range() uses find_next_system_ram() to find the next ram
resource.  This in turn only travels through siblings of top level child
and does not travers through all the nodes of the resoruce tree.  I also
need another function where I can walk through all the resources, for
example figure out where "GART" aperture is.  Figure out where ACPI memory
is.

So I wrote another function walk_iomem_res() which walks through all
/proc/iomem resources and returns matches as asked by caller.  Caller can
specify "name" of resource, start and end and flags.

Got rid of find_next_system_ram_res() and instead implemented more generic
find_next_iomem_res() which can be used to traverse top level children
only based on an argument.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Let's use the more common "unusable".

This patch was originally written and posted by Boris. I am including it
in this patch series.
Signed-off-by: NBorislav Petkov <bp@suse.de>
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>