Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The SRP sysfs attribute is dependent on gadget mode; any
gadget may support SRP.  But "rmmod musb_hdrc" didn't
remove that attribute; fix.
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Acked-by: NFelipe Balbi <me@felipebalbi.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If this is not done, khubd will not be informed of the disconnect
and will assume the device is still there.

Easily seen when a hub is connected with no device attached to it;
it will autosuspend.  When the hub is disconnected, it still shows
up in /proc/bus/usb/devices
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove wrongly applied upper limit on the interrupt transfer
interval for low speed devices (not much of an error per se,
according to USB specs).
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO
count in musb_host_tx() risks sending a short packet prematurely for
transfer sizes over 64 KB.

Similarly, although data transfer size shouldn't exceed 65535 bytes for
the control endpoint, making musb_h_ep0_continue() more robust WRT URBs
with possibly oversized buffer will not hurt either...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For some strange reason the host side musb_giveback() decides
that it's always got an IN transfer when the hardware endpoint
is using a shared FIFO.  This causes musb_save_toggle() to read
the toggle state from the RXCSR register instead of TXCSR, and
may also cause unneeded reloading of RX endpoint registers.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The musb_h_disable() routine can oops in some cases:

 - It's not safe to read hep->hcpriv outside musb->lock,
   since it gets changed on completion IRQ paths.

 - The list iterators aren't safe to use in that way;
   just remove the first element while !list_empty(),
   so deletions on other code paths can't make trouble.

We need two "scrub the list" loops because only one branch
should touch hardware and advance the schedule.

[ dbrownell@users.sourceforge.net: massively simplify
  patch description; add key points as code comments ]
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The urb_dequeue() method forgets to unlink 'struct musb_qh' from the
control or bulk schedules when the URB being cancelled is the only
one queued to its endpoint.  That will cause musb_advance_schedule()
to block once it reaches 'struct musb_qh' with now empty URB list, so
URBs queued for other endpoints after the one being dequeued will not
be served.

Fix by unlinking the QH from the list except when it's already being
handled (typically by musb_giveback).  Since a QH with an empty URB
list is now supposed to be freed, do that.  And remove a now-useless
check from musb_advance_schedule().

[ dbrownell@users.sourceforge.net: update patch description,
  and fold in a dequeue() comment patch ]
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The input queue should be used for TX on endpoints which
share FIFO hardware.  The host TX path wasn't doing that.

Shared FIFOs are most often configured for periodic endpoints,
which are mostly used for RX/IN transfers ... that's probably
how this bug managed to linger for a long time.

[ dbrownell@users.sourceforge.net: update patch description ]
Signed-off-by: NDmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

request->actual is an unsigned and we should use the same
variable type for fifo_count otherwise we might lose some
data if request->length >= 64kbytes.

[ dbrownell@users.sourceforge.net: fix compiler warning ]
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:

 - Use clk_enable()/clk_disable() ... the "always enable USB clocks"
   code this originally relied on has since been removed.

 - Initialize the USB device only after the relevant I2C GPIOs are
   available, so the host side can properly enable VBUS.

 - Tweak init sequencing to cope with mainline's relatively late init
   of the I2C system bus for power switches, transceivers, and so on.

Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested.  Also
verified on OMAP3.

(Unrelated:  correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1218) fixes a problem with a radio-control joystick used
in the "walkera 4#3" helicopter.  This device responds to the initial
Get-String-Descriptor request for string 0 (which is really the list
of supported languages) by sending its config descriptor!  The
usb_get_string() routine needs to check whether it got the right
type of descriptor.

Oddly enough, this sort of check is already present in
usb_get_descriptor().  The patch changes the error code from -EPROTO
to -ENODATA, because -EPROTO shows up in so many other contexts to
indicate a hardware failure rather than a firmware error.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NGuillermo Jarabo <williamjap@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

===================================================================

In apollon case, it only used udc, so udc configuration should select
USB_OTG_UTILS also.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1220) automatically disables stalls when g_file_storage
finds itself running with an Atmel device controller, because the
Atmel hardware/driver isn't capable of halting bulk endpoints
correctly.
Reported-by: NStanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1219) adds the IGNORE_RESIDUE flag to the unusual_devs
entries for Genesys Logic's USB-IDE adapter.  Although this device
usually gets the residue correct, there is one command crucial to the
operation of CD and DVD drives which it messes up.
Tested-by: NMike Lampard <mike@mtgambier.net>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAdam J. Richter <adam_richter2004@yahoo.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I noticed that my revision of the F3507G WWAN card isn't listed in
drivers/usb/serial/option.c
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the cdc-acm driver can
properly handle this combined device.
Signed-off-by: NDmitriy Taychenachev <dimichxp@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch addes the BenQ 3g modem support to the option driver.


From: Jesse Sung <jsung@novell.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We where selecting wrong ep descriptors causing
some troubles while sending files over obex interface.

The problem was a typo while usb_find_endpoint() was being
called for HS endpoints.
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently ITDs are immediately recycled whenever their URB completes.
However, EHCI hardware can sometimes remember some ITD state.  This
means that when the ITD is reused before end-of-frame it may sometimes
cause the hardware to reference bogus state.

This patch defers reusing such ITDs by moving them into a new ehci member
cached_itd_list. ITDs resting in cached_itd_list are moved back into their
stream's free_list once scan_periodic() detects that the active frame has
elapsed.

This makes the snd_usb_us122l driver (in kernel since .28) work right
when it's hooked up through EHCI.

[ dbrownell@users.sourceforge.net: comment fixups ]
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Tested-by: NPhilippe Carriere <philippe-f.carriere@wanadoo.fr>
Tested-by: NFederico Briata <federicobriata@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Clear next TD field and status field in queue head initialization code
to prevent unpredictable result caused by residue of usb reset.
Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

*ep->reg_udccs is always set to 0.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If a USB PCI controller is behind a cardbus bridge, we are trying to
restore its configuration registers too early, before the cardbus
bridge is operational.  To fix this, call pci_restore_state() from
usb_hcd_pci_resume() and remove usb_hcd_pci_resume_early() which is
no longer necessary (the configuration spaces of USB controllers that
are not behind cardbus bridges will be restored by the PCI PM core
with interrupts disabled anyway).

This patch fixes the regression from 2.6.28 tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12659

[ Side note: the proper long-term fix is probably to just force the
  unplug event at suspend time instead of doing a plug/unplug at resume
  time, but this patch is fine regardless  - Linus ]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reported-by: NMiles Lane <miles.lane@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Always lock whc->lock with spin_lock_irq() or spin_lock_irqsave().
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>

This device suffers from the off-by-one error when reporting the capacity,
so add US_FL_FIX_CAPACITY to the existing entry.
Signed-off-by: NNick Holloway <Nick.Holloway@pyrites.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NIvan Kuten <ivan.kuten@promwad.com>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- New Novatel and Dell mobile broadband modem products added
 - Dell pid variables used in stead of numerical PIDs for known
   products
Signed-off-by: NDirk De Schepper <ddeschepper@nvtl.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds device IDs and balances the counts to make the
hot ID additioning mechanism work.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Cc: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There was one error path where unlock_kernel() wasn't called.

This was found with a code checker (http://repo.or.cz/w/smatch.git/)
Compile tested only, sorry.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1202) adds Pentax to usb-storage's list of bad vendors
whose devices always need the CAPACITY_HEURISTICS flag.  This is in
addition to the existing entries: Nokia, Nikon, and Motorola.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NVirgo Pärna <virgo.parna@mail.ee>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for the NDI Polaris system *http://www.ndigital.com/).

Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The failure path of aircable_init is wrong, fix the order of (goto) labels.
Signed-off-by: NDave Young <hidave.darkstar@gmail.com>
Acked-by: NNaranjo Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1201) removes the WARN() from the last-sector hacks in
usb-storage, thereby making the code match the version now in
.27-stable and .28-stable.  The WARN() isn't needed, since there is no
longer any intention of assuming that all storage devices have an even
number of sectors, and it annoys users for no good reason.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Revert 8b6346ec as these devices really
work just fine with the cdc-acm driver, as they follow the spec
properly.

Thanks to Chuck Ebbert for pointing out the problem here.

Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The same patch to add support for MTK gps loggers was submitted by two
different people and applied twice. Remove the redundant lines.
Signed-off-by: NJames Treacy <treacy@debian.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While disabling an endpoint the driver nuking any pending requests,
thus completing them with -ESHUTDOWN status. But the driver doesn't
clear the tx_req, which means that a next TX request (after
ep_enable), might get stalled, since the driver won't queue the new
reqests.

This patch fixes a bug I'm observing with ethernet gadget while
playing with ifconfig usb0 up/down (the up/down sequence disables
and enables `in' and `out' endpoints).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Before freeing an endpoint's muram memory, we should stop all activity
of the endpoint, otherwise the QE UDC controller might do nasty things
with the muram memory that isn't belong to that endpoint anymore.

The qe_ep_reset() effectively flushes the hardware fifos, finishes all
late transaction and thus prevents the corruption.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Freescale QE UDC controllers can't report the "port change" states,
so the only way to handle disconnects is to process bus reset
interrupts. The bus reset can take some time, that is, few irqs.
Gadgets may print the disconnection events, and this causes few
repetitive messages in the kernel log.

This patch fixes the issue by using the usb_state machine, if the
usb controller has been already reset, just quit the reset irq
early.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

qe_udc_reg_init() leaves the USB controller enabled before muram memory
initialized. Sometimes the uninitialized muram memory confuses the
controller, and it start sending the busy interrupts.

Fix this by disabling the controller, it will be enabled later by
the gadget driver, at bind time.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>