Noticed by Ingo Molnar.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

queue restart tasklets need to be stopped after napi handlers are stopped
since the latter can restart them.  So stop them after stopping napi.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting with commit a3bc1f11 ("gianfar: Revive SKB
recycling") gianfar driver sooner or later stops transmitting any
packets on SMP machines.

start_xmit() prepares new skb for transmitting, generally it does
three things:

1. sets up all BDs (marks them ready to send), except the first one.
2. stores skb into tx_queue->tx_skbuff so that clean_tx_ring()
   would cleanup it later.
3. sets up the first BD, i.e. marks it ready.

Here is what clean_tx_ring() does:

1. reads skbs from tx_queue->tx_skbuff
2. checks if the *last* BD is ready. If it's still ready [to send]
   then it it isn't transmitted, so clean_tx_ring() returns.
   Otherwise it actually cleanups BDs. All is OK.

Now, if there is just one BD, code flow:

- start_xmit(): stores skb into tx_skbuff. Note that the first BD
  (which is also the last one) isn't marked as ready, yet.
- clean_tx_ring(): sees that skb is not null, *and* its lstatus
  says that it is NOT ready (like if BD was sent), so it cleans
  it up (bad!)
- start_xmit(): marks BD as ready [to send], but it's too late.

We can fix this simply by reordering lstatus/tx_skbuff writes.
Reported-by: NMartyn Welch <martyn.welch@ge.com>
Bisected-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: NMartyn Welch <martyn.welch@ge.com>
Cc: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Cc: Stable <stable@vger.kernel.org> [2.6.33]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

r8169 needs certain writes to be visible to other CPUs or the NIC before
touching the hardware, but was using smp_wmb() which is only required to
order cacheable memory access. Switch to wmb() which is required to
order both cacheable and non-cacheable memory.

Noticed by Catalin Marinas and Paul Mackerras.
Signed-off-by: NDavid Dillow <dave@thedillows.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix TIPC to disallow sending to remote addresses prior to entering NET_MODE

user programs can oops the kernel by sending datagrams via AF_TIPC prior to
entering networked mode.  The following backtrace has been observed:

ID: 13459  TASK: ffff810014640040  CPU: 0   COMMAND: "tipc-client"
[exception RIP: tipc_node_select_next_hop+90]
RIP: ffffffff8869d3c3  RSP: ffff81002d9a5ab8  RFLAGS: 00010202
RAX: 0000000000000001  RBX: 0000000000000001  RCX: 0000000000000001
RDX: 0000000000000000  RSI: 0000000000000001  RDI: 0000000001001001
RBP: 0000000001001001   R8: 0074736575716552   R9: 0000000000000000
R10: ffff81003fbd0680  R11: 00000000000000c8  R12: 0000000000000008
R13: 0000000000000001  R14: 0000000000000001  R15: ffff810015c6ca00
ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
RIP: 0000003cbd8d49a3  RSP: 00007fffc84e0be8  RFLAGS: 00010206
RAX: 000000000000002c  RBX: ffffffff8005d116  RCX: 0000000000000000
RDX: 0000000000000008  RSI: 00007fffc84e0c00  RDI: 0000000000000003
RBP: 0000000000000000   R8: 00007fffc84e0c10   R9: 0000000000000010
R10: 0000000000000000  R11: 0000000000000246  R12: 0000000000000000
R13: 00007fffc84e0d10  R14: 0000000000000000  R15: 00007fffc84e0c30
ORIG_RAX: 000000000000002c  CS: 0033  SS: 002b

What happens is that, when the tipc module in inserted it enters a standalone
node mode in which communication to its own address is allowed <0.0.0> but not
to other addresses, since the appropriate data structures have not been
allocated yet (specifically the tipc_net pointer).  There is nothing stopping a
client from trying to send such a message however, and if that happens, we
attempt to dereference tipc_net.zones while the pointer is still NULL, and
explode.  The fix is pretty straightforward.  Since these oopses all arise from
the dereference of global pointers prior to their assignment to allocated
values, and since these allocations are small (about 2k total), lets convert
these pointers to static arrays of the appropriate size.  All the accesses to
these bits consider 0/NULL to be a non match when searching, so all the lookups
still work properly, and there is no longer a chance of a bad dererence
anywhere.  As a bonus, this lets us eliminate the setup/teardown routines for
those pointers, and elimnates the need to preform any locking around them to
prevent access while their being allocated/freed.

I've updated the tipc_net structure to behave this way to fix the exact reported
problem, and also fixed up the tipc_bearers and media_list arrays to fix an
obvious simmilar problem that arises from issuing tipc-config commands to
manipulate bearers/links prior to entering networked mode

I've tested this for a few hours by running the sanity tests and stress test
with the tipcutils suite, and nothing has fallen over.  There have been a few
lockdep warnings, but those were there before, and can be addressed later, as
they didn't actually result in any deadlock.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Allan Stephens <allan.stephens@windriver.com>
CC: David S. Miller <davem@davemloft.net>
CC: tipc-discussion@lists.sourceforge.net

 bearer.c |   37 ++++++-------------------------------
 bearer.h |    2 +-
 net.c    |   25 ++++---------------------
 3 files changed, 11 insertions(+), 53 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipgre_header() can be called with zero daddr when the gre device is
configured as multipoint tunnel and still has the NOARP flag set (which is
typically cleared by the userspace arp daemon).  If the NOARP packets are
not dropped, ipgre_tunnel_xmit() will take rt->rt_gateway (= NBMA IP) and
use that for route look up (and may lead to bogus xfrm acquires).

The multicast address check is removed as sending to multicast group should
be ok.  In fact, if gre device has a multicast address as destination
ipgre_header is always called with multicast address.
Signed-off-by: NTimo Teras <timo.teras@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Decreases the odds wakee will suffer from frequent cache misses.
Signed-off-by: NMike Galbraith <efault@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This solves a potential race problem during the cleanup process.
The issue is that addrconf_ifdown() needs to traverse address list,
but then drop lock to call the notifier. The version in -next
could get confused if add/delete happened during this window.
Original code (2.6.32 and earlier) was okay because all addresses
were always deleted.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

My recent change in net-next to retain permanent addresses caused regression.
Device refcount would not go to zero when device was unregistered because
left over anycast reference would hold ipv6 dev reference which would hold
device references...

The correct procedure is to call notify chain when address is no longer
available for use.  When interface comes back DAD timer will notify
back that address is available.

Also, link local addresses should be purged when interface is brought
down. The address might be changed.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Router Solicitation timer races with device state changes
because it doesn't lock the device. Use local variable to avoid
one repeated dereference.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Timer code runs in bottom half, so there is no need for
using _bh form of locking.  Also check if device is not ready
to avoid race with address that is no longer active.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export rt2x00soc_probe from rt2x00soc as it is used in rt2800pci.

Otherwise loading rt2800pci gives "rt2800pci: Unknown symbol
rt2x00soc_probe".
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.

This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.

Fix this by passing the new channel type to the driver.

Cc: stable@kernel.org
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

br_multicast calls ip_send_check(), so it should depend on INET.

built-in:
br_multicast.c:(.text+0x88cf4): undefined reference to `ip_send_check'

or modular:
ERROR: "ip_send_check" [net/bridge/bridge.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed FW 5.2.7.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This off by one error was found by smatch.

drivers/net/davinci_emac.c +2390 emac_dev_open(13) error: buffer overflow 'priv->mac_addr' 6 <= 6
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are only 6 link_modes.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The inquiry cache information in debugfs should be using seq_file support
and not allocating memory on the stack for the string. Since the usage of
these information is really seldom, using single_open() for it is good
enough.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

My previous patch 914c8ad2 incorrectly changed
the length check in packet_mc_add to be more strict. The problem is that
userspace is not filling this field (and it stays zeroed) in case of setting
PACKET_MR_PROMISC or PACKET_MR_ALLMULTI. So move the strict check to the point
in path where the addr_len must be set correctly.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Reported-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding code to update NCSI section while updating firmware on the controller.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original code dereferenced "cpmac_mii" after calling
"mdiobus_free(cpmac_mii);"
Signed-off-by: NDan Carpenter <error27@gmail.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I merged the bundle creation code, I introduced a bogus
flowi value in the bundle.  Instead of getting from the caller,
it was instead set to the flow in the route object, which is
totally different.

The end result is that the bundles we created never match, and
we instead end up with an ever growing bundle list.

Thanks to Jamal for find this problem.
Reported-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Acked-by: NSteffen Klassert <steffen.klassert@secunet.com>
Acked-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the wireless summit in Portland we discussed a way of
loading firmware asynchronously from ->probe() before
registration to mac80211, in order to register with the
wireless subsystems with complete information in cases
where firmware is required to know parameters.

This is not yet the case in iwlwifi, but for some new
features we're working on it will be the case since
those will only be supported by new firmware images.

Hence, to start with, convert iwlwifi to load firmware
asynchronously from probe, unbinding the device when
firmware loading fails, and only registering with the
wireless subsystems after firmware has been loaded
successfully.

Future patches will hook into this to register the
new firmware capabilities, depending on the firmware
API version.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This converts ar9170 to load firmware asynchronously
out of ->probe() and only register with mac80211 when
all firmware has been loaded successfully. If, on the
other hand, any firmware fails to load, it will now
unbind from the device.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Compiling rt2800pci with CONFIG_RT2800PCI_SOC fails with "... rt2880pci.c:
error: incompatible type for argument 2 of 'rt2x00soc_probe'".

Fix this by using &rt2800pci_ops instead of rt2800pci_ops.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for CEIVA USB wireless adapters to the rt73usb driver.
Signed-off-by: NBryan Polk <sainth@eidolons.org>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit e1dd33f60ced091114e4aacf141e0d03b88d3e13 changed cfg80211 to
allow association commands while in associated state to enable support
for roaming within an ESS. However, this was not enough to resolve all
cases with mac80211 which needs some additional handling of the
reassociation case to clear internal state with the BSS that was in use
previously.

This patch makes ieee80211_mgd_assoc() accept a valid reassociation
command and clean the association state with the previous BSS. This
fixes roaming between BSSes in an ESS when using wpa_supplicant with
-Dnl80211.
Signed-off-by: NJouni Malinen <j@w1.fi>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since txq->axq_lock may be hold in softirq context, it must be
acquired with spin_lock_bh() instead of spin_lock() if softieq is
enabled.

The patch fixes the lockdep warning below when unloading ath9k modules.

=================================
[ INFO: inconsistent lock state ]
2.6.33-wl #12
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
rmmod/3642 [HC0[0]:SC0[0]:HE1:SE1] takes:
 (&(&txq->axq_lock)->rlock){+.?...}, at: [<ffffffffa03568c3>] ath_tx_node_cleanup+0x62/0x180 [ath9k]
{IN-SOFTIRQ-W} state was registered at:
  [<ffffffff8107577d>] __lock_acquire+0x2f6/0xd35
  [<ffffffff81076289>] lock_acquire+0xcd/0xf1
  [<ffffffff813a7486>] _raw_spin_lock_bh+0x3b/0x6e
  [<ffffffffa0356b49>] spin_lock_bh+0xe/0x10 [ath9k]
  [<ffffffffa0358ec7>] ath_tx_tasklet+0xcd/0x391 [ath9k]
  [<ffffffffa0354f5f>] ath9k_tasklet+0x70/0xc8 [ath9k]
  [<ffffffff8104e601>] tasklet_action+0x8c/0xf4
  [<ffffffff8104f459>] __do_softirq+0xf8/0x1cd
  [<ffffffff8100ab1c>] call_softirq+0x1c/0x30
  [<ffffffff8100c2cf>] do_softirq+0x4b/0xa3
  [<ffffffff8104f045>] irq_exit+0x4a/0x8c
  [<ffffffff813acccc>] do_IRQ+0xac/0xc3
  [<ffffffff813a7d53>] ret_from_intr+0x0/0x16
  [<ffffffff81302d52>] cpuidle_idle_call+0x9e/0xf8
  [<ffffffff81008be7>] cpu_idle+0x62/0x9d
  [<ffffffff81391c1a>] rest_init+0x7e/0x80
  [<ffffffff818bbd38>] start_kernel+0x3e8/0x3f3
  [<ffffffff818bb2bc>] x86_64_start_reservations+0xa7/0xab
  [<ffffffff818bb3b8>] x86_64_start_kernel+0xf8/0x107
irq event stamp: 42037
hardirqs last  enabled at (42037): [<ffffffff813a7b21>] _raw_spin_unlock_irqrestore+0x47/0x56
hardirqs last disabled at (42036): [<ffffffff813a72f4>] _raw_spin_lock_irqsave+0x2b/0x88
softirqs last  enabled at (42000): [<ffffffffa0353ea6>] spin_unlock_bh+0xe/0x10 [ath9k]
softirqs last disabled at (41998): [<ffffffff813a7463>] _raw_spin_lock_bh+0x18/0x6e

other info that might help us debug this:
4 locks held by rmmod/3642:
 #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff8132c10d>] rtnl_lock+0x17/0x19
 #1:  (&wdev->mtx){+.+.+.}, at: [<ffffffffa01e53f2>] cfg80211_netdev_notifier_call+0x28d/0x46d [cfg80211]
 #2:  (&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0260834>] ieee80211_mgd_deauth+0x3f/0x17e [mac80211]
 #3:  (&local->sta_mtx){+.+.+.}, at: [<ffffffffa025a381>] sta_info_destroy_addr+0x2b/0x5e [mac80211]

stack backtrace:
Pid: 3642, comm: rmmod Not tainted 2.6.33-wl #12
Call Trace:
 [<ffffffff81074469>] valid_state+0x178/0x18b
 [<ffffffff81014f94>] ? save_stack_trace+0x2f/0x4c
 [<ffffffff81074e08>] ? check_usage_backwards+0x0/0x88
 [<ffffffff8107458f>] mark_lock+0x113/0x230
 [<ffffffff810757f1>] __lock_acquire+0x36a/0xd35
 [<ffffffff8101018d>] ? native_sched_clock+0x2d/0x5f
 [<ffffffffa03568c3>] ? ath_tx_node_cleanup+0x62/0x180 [ath9k]
 [<ffffffff81076289>] lock_acquire+0xcd/0xf1
 [<ffffffffa03568c3>] ? ath_tx_node_cleanup+0x62/0x180 [ath9k]
 [<ffffffff810732eb>] ? trace_hardirqs_off+0xd/0xf
 [<ffffffff813a7193>] _raw_spin_lock+0x36/0x69
 [<ffffffffa03568c3>] ? ath_tx_node_cleanup+0x62/0x180 [ath9k]
 [<ffffffffa03568c3>] ath_tx_node_cleanup+0x62/0x180 [ath9k]
 [<ffffffff810749ed>] ? trace_hardirqs_on+0xd/0xf
 [<ffffffffa0353950>] ath9k_sta_remove+0x22/0x26 [ath9k]
 [<ffffffffa025a08f>] __sta_info_destroy+0x1ad/0x38c [mac80211]
 [<ffffffffa025a394>] sta_info_destroy_addr+0x3e/0x5e [mac80211]
 [<ffffffffa02605d6>] ieee80211_set_disassoc+0x175/0x180 [mac80211]
 [<ffffffffa026084d>] ieee80211_mgd_deauth+0x58/0x17e [mac80211]
 [<ffffffff813a60c1>] ? __mutex_lock_common+0x37f/0x3a4
 [<ffffffffa01e53f2>] ? cfg80211_netdev_notifier_call+0x28d/0x46d [cfg80211]
 [<ffffffffa026786e>] ieee80211_deauth+0x1e/0x20 [mac80211]
 [<ffffffffa01f47f9>] __cfg80211_mlme_deauth+0x130/0x13f [cfg80211]
 [<ffffffffa01e53f2>] ? cfg80211_netdev_notifier_call+0x28d/0x46d [cfg80211]
 [<ffffffff810732eb>] ? trace_hardirqs_off+0xd/0xf
 [<ffffffffa01f7eee>] __cfg80211_disconnect+0x111/0x189 [cfg80211]
 [<ffffffffa01e5433>] cfg80211_netdev_notifier_call+0x2ce/0x46d [cfg80211]
 [<ffffffff813aa9ea>] notifier_call_chain+0x37/0x63
 [<ffffffff81068c98>] raw_notifier_call_chain+0x14/0x16
 [<ffffffff81322e97>] call_netdevice_notifiers+0x1b/0x1d
 [<ffffffff8132386d>] dev_close+0x6a/0xa6
 [<ffffffff8132395f>] rollback_registered_many+0xb6/0x2f4
 [<ffffffff81323bb8>] unregister_netdevice_many+0x1b/0x66
 [<ffffffffa026494f>] ieee80211_remove_interfaces+0xc5/0xd0 [mac80211]
 [<ffffffffa02580a2>] ieee80211_unregister_hw+0x47/0xe8 [mac80211]
 [<ffffffffa035290e>] ath9k_deinit_device+0x7a/0x9b [ath9k]
 [<ffffffffa035bc26>] ath_pci_remove+0x38/0x76 [ath9k]
 [<ffffffff8120940a>] pci_device_remove+0x2d/0x51
 [<ffffffff8129d797>] __device_release_driver+0x7b/0xd1
 [<ffffffff8129d885>] driver_detach+0x98/0xbe
 [<ffffffff8129ca7a>] bus_remove_driver+0x94/0xb7
 [<ffffffff8129ddd6>] driver_unregister+0x6c/0x74
 [<ffffffff812096d2>] pci_unregister_driver+0x46/0xad
 [<ffffffffa035bae1>] ath_pci_exit+0x15/0x17 [ath9k]
 [<ffffffffa035e1a2>] ath9k_exit+0xe/0x2f [ath9k]
 [<ffffffff8108050a>] sys_delete_module+0x1c7/0x236
 [<ffffffff813a7df5>] ? retint_swapgs+0x13/0x1b
 [<ffffffff810749b5>] ? trace_hardirqs_on_caller+0x119/0x144
 [<ffffffff8109b9f6>] ? audit_syscall_entry+0x11e/0x14a
 [<ffffffff81009bb2>] system_call_fastpath+0x16/0x1b
wlan1: deauthenticating from 00:23:cd:e1:f9:b2 by local choice (reason=3)
PM: Removing info for No Bus:wlan1
cfg80211: Calling CRDA to update world regulatory domain
PM: Removing info for No Bus:rfkill2
PM: Removing info for No Bus:phy1
ath9k 0000:16:00.0: PCI INT A disabled
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The first chunk fixes a debugging assert to print a warning about array underflows.
The second chunk corrects a potential array underflow.  I also removed an assert
in the second chunk because it can no longer happen.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NBenoit Papillault <benoit.papillault@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for handling KEY_RFKILL in the rfkill input module. This
simply toggles the state of all rfkill devices. The comment in rfkill.h
is also updated to reflect that RFKILL_TYPE_ALL may be used inside the
kernel.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Even if keylen == 0 is a bug and should not really happen, better avoid
possibility of passing bad value to firmware.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux: (49 commits)
  OMAP: DSS2: Taal: Fix TE when resuming
  OMAP: DSS2: Taal: Fix ESD check
  OMAP: DSS2: OMAPFB: Constify some function parameters
  OMAP: DSS2: OMAPFB: install omapfb.h
  OMAP: DSS2: DSI: add error prints
  OMAP: DSS2: TPO-TD03MTEA1: fix function names
  OMAP: DSS2: DSI: add dsi_vc_dcs_read_2() helper
  OMAP: DSS2: OMAPFB: Remove FB_OMAP2_FORCE_AUTO_UPDATE
  OMAP: DSS2: DSI: remove external TE support
  OMAP: DSS2: move timing functions
  OMAP: DSS2: move set/get_wss()
  OMAP: DSS2: move enable/disable/suspend/resume
  OMAP: DSS2: move update() and sync()
  OMAP: DSS2: move set/get_update_mode()
  OMAP: DSS2: move enable/get_te()
  OMAP: DSS2: move get_recommended_bpp()
  OMAP: DSS2: move get_resolution()
  OMAP: DSS2: move enable/disable_channel to overlay manager
  OMAP: DSS2: move wait_vsync()
  OMAP: DSS2: move get/set_rotate()
  ...

Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (214 commits)
  omap2: Initialize Menelaus and MMC for N8X0
  AM3517 EVM: correct typo - tca6416 mispelt as tca6516
  AM3517 EVM: Enable I2C support
  AM35x: Enable OMAP_MUX in defconfig
  AM35x: Add missing GPIO mux config for EHCI port
  Zoom3: Defconfig update
  omap: i2c: Fix muxing for command line enabled bus
  OMAP4: clock: Remove clock hacks from timer-gp.c
  OMAP4: clock: Add dummy clock nodes for interface clocks
  OMAP4: clock: Rename leaf clock nodes to end with a _ick or _fck
  OMAP2+ clock: revise omap2_clk_{disable,enable}()
  OMAP2/3 clock: combine OMAP2 & 3 boot-time MPU rate change code
  OMAP clockdomain: if no autodeps exist, don't try to add or remove them
  OMAP hwmod: add hwmod class support
  OMAP hwmod: convert header files with static allocations into C files
  OMAP hwmod: convert hwmod to use hardware clock names rather than clkdev dev+con
  OMAP clock: add omap_clk_get_by_name() for use by OMAP hwmod core code
  OMAP3: clock: add capability to change rate of dpll4_m5_ck_3630
  OMAP4 clock: drop the ALWAYS_ENABLED clock flag
  OMAP clock: drop RATE_FIXED clock flag
  ...

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  Revert "blkdev: fix merge_bvec_fn return value checks"

This reverts commit 9f7cdbc3.

It's causing oopses om dm setups, so revert it until we investigate.
Reported-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
  sparc: Support show_unhandled_signals.
  sparc: use __ratelimit
  sunxvr500: Additional PCI id for sunxvr500 driver
  sparc: use asm-generic/scatterlist.h
  sparc64: If 'slot-names' property exist, create sysfs PCI slot information.
  sparc: remove trailing space in messages
  sparc: remove redundant return statements

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
  virtio_net: remove forgotten assignment
  be2net: fix tx completion polling
  sis190: fix cable detect via link status poll
  net: fix protocol sk_buff field
  bridge: Fix build error when IGMP_SNOOPING is not enabled
  bnx2x: Tx barriers and locks
  scm: Only support SCM_RIGHTS on unix domain sockets.
  vhost-net: restart tx poll on sk_sndbuf full
  vhost: fix get_user_pages_fast error handling
  vhost: initialize log eventfd context pointer
  vhost: logging thinko fix
  wireless: convert to use netdev_for_each_mc_addr
  ethtool: do not set some flags, if others failed
  ipoib: returned back addrlen check for mc addresses
  netlink: Adding inode field to /proc/net/netlink
  axnet_cs: add new id
  bridge: Make IGMP snooping depend upon BRIDGE.
  bridge: Add multicast count/interval sysfs entries
  bridge: Add hash elasticity/max sysfs entries
  bridge: Add multicast_snooping sysfs toggle
  ...

Trivial conflicts in Documentation/feature-removal-schedule.txt

TE was not initialized properly on power on, which broke TE when resuming
from suspend.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

This is no longer needed. I missed to remove this in
567ec874 ("net: convert multiple
drivers to use netdev_for_each_mc_addr, part6")
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>