Currently, the VFs do not read the default VLAN during initialization,
so they will not be able to indicate untagged frames properly.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Corrected a spelling mistake that was found over time.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
Acked-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Output of ethtool was reporting 2 rx_errors entries. This change
removes one of the redundant entries.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>

The function collecting Tx statistics was actually using values from the RX
ring. Thus, Tx and Rx statistics values reported by "ifconfig" will
return identical values. This change corrects this error and the Tx
statistics is now reading from the Tx ring.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>

The dwmac-socfpga.c conflict was a case of a bug fix overlapping
changes in net-next to handle an error pointer differently.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
cxgb4: Misc. fixes for sge

Increases value of MAX_IMM_TX_PKT_LEN to improve latency, fill freelist
starving threshold based on adapter type, add comments for tx flits and sge
length code and don't call t4_slow_intr_handler when we are not master PF.

This patch series has been created against net-next tree and includes patches on
cxgb4 driver

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add comment for tx filt and sge length calucaltion code, also remove
a hardcoded value
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fl_starv_thres could be different from adapter to adapter, don't use
hardcoded values
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows a significant latency drop for packets of sizes between 128 and 192
bytes
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ring size is always known at compile time, so make the code a bit
more efficient
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver needs to inform the hardware about the first invalid (not yet
filled) rx slot, by writing its DMA descriptor pointer offset to the
BGMAC_DMA_RX_INDEX register.

This register was set to a value exceeding the rx ring size, effectively
allowing the hardware constant access to the full ring, regardless of
which slots are initialized.

To fix this issue, always mark the last filled rx slot as invalid.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of allocating buffers at device init time and initializing
descriptors at device open, do both at the same time (during open).
Free all buffers when closing the device.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Limiting it to 511 looks like a failed attempt at leaving one descriptor
empty to allow the hardware to stop processing a buffer that has not
been prepared yet. However, this doesn't work because this affects the
total ring size as well
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In very rare cases, the MAC can catch an internal buffer that is bigger
than it's supposed to be. Instead of crashing the kernel, simply pass
the buffer back to the hardware
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate a new buffer before processing the completed one. If allocation
fails, reuse the old buffer.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A packet buffer offset of 30 bytes is inefficient, because the first 2
bytes end up in a different cacheline.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Always poll rx and tx during NAPI poll instead of relying on the status
of the first interrupt. This prevents bgmac_poll from leaving unfinished
work around until the next IRQ.
In my tests this makes bridging/routing throughput under heavy load more
stable and ensures that no new IRQs arrive as long as bgmac_poll uses up
the entire budget.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep incrementing ring->start and ring->end instead of pointing it to
the actual ring slot entry. This simplifies the calculation of the
number of free slots.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The toshiba drivers had celleb as an optional dependency.
celleb has been dropped [1], so clean that out of Kconfig.

[1] http://patchwork.ozlabs.org/patch/451730/

CC: netdev@vger.kernel.org
CC: Valentin Rothberg <valentinrothberg@gmail.com>
CC: mpe@ellerman.id.au
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If remaining space in a send buffer slot is too small for the whole message,
we only copy the RNDIS header and PPI data into send buffer, so we can batch
one more packet each time. It reduces the vmbus per-message overhead.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Al Viro says:

====================
netdev-related stuff in vfs.git

There are several commits sitting in vfs.git that probably ought to go in
via net-next.git.  First of all, there's merge with vfs.git#iocb - that's
Christoph's aio rework, which has triggered conflicts with the ->sendmsg()
and ->recvmsg() patches a while ago.  It's not so much Christoph's stuff
that ought to be in net-next, as (pretty simple) conflict resolution on merge.
The next chunk is switch to {compat_,}import_iovec/import_single_range - new
safer primitives for initializing iov_iter.  The primitives themselves come
from vfs/git#iov_iter (and they are used quite a lot in vfs part of queue),
conversion of net/socket.c syscalls belongs in net-next, IMO.  Next there's
afs and rxrpc stuff from dhowells.  And then there's sanitizing kernel_sendmsg
et.al.  + missing inlined helper for "how much data is left in msg->msg_iter" -
this stuff is used in e.g.  cifs stuff, but it belongs in net-next.

That pile is pullable from
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs.git for-davem

I'll post the individual patches in there in followups; could you take a look
and tell if everything in there is OK with you?
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using a timer wheel for timewait sockets was nice ~15 years ago when
memory was expensive and machines had a single processor.

This does not scale, code is ugly and source of huge latencies
(Typically 30 ms have been seen, cpus spinning on death_lock spinlock.)

We can afford to use an extra 64 bytes per timewait sock and spread
timewait load to all cpus to have better behavior.

Tested:

On following test, /proc/sys/net/ipv4/tcp_tw_recycle is set to 1
on the target (lpaa24)

Before patch :

lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
419594

lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
437171

While test is running, we can observe 25 or even 33 ms latencies.

lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20601ms
rtt min/avg/max/mdev = 0.020/0.217/25.771/1.535 ms, pipe 2

lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20702ms
rtt min/avg/max/mdev = 0.019/0.183/33.761/1.441 ms, pipe 2

After patch :

About 90% increase of throughput :

lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
810442

lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
800992

And latencies are kept to minimal values during this load, even
if network utilization is 90% higher :

lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 19991ms
rtt min/avg/max/mdev = 0.023/0.064/0.360/0.042 ms
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The printed values are all of type unsigned integer, therefore use
%u instead of %d. Otherwise an user can face negative values.
Signed-off-by: NRichard Weinberger <richard@nod.at>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The printed values are all of type unsigned integer, therefore use
%u instead of %d. Otherwise an user can face negative values.

Fixes:
$ cat /proc/net/netfilter/nfnetlink_queue
    0  29508   278 2 65531     0 2004213241 -2129885586  1
    1 -27747     0 2 65531     0     0        0  1
    2 -27748     0 2 65531     0     0        0  1
Signed-off-by: NRichard Weinberger <richard@nod.at>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netlink portid is an unsigned integer, use this type
also in netfilter.
Signed-off-by: NRichard Weinberger <richard@nod.at>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

portid is an unsigned integer. Fix urelease_work to
match all other portid user in the kernel.
Signed-off-by: NRichard Weinberger <richard@nod.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

portid is an unsigned integer. Fix netlink_notify to
match all other portid user in the kernel.
Signed-off-by: NRichard Weinberger <richard@nod.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since retransmitted segments are not used for RTT estimation, previously
SACKed segments present in the rtx queue are used. This estimation can be
several times larger than the actual RTT. When a cumulative ack covers both
previously SACKed and retransmitted segments, CC may thus get a bogus RTT.

Such segments previously had an RTT estimation in tcp_sacktag_one(), so it
seems reasonable to not reuse them in tcp_clean_rtx_queue() at all.

Afaik, this has had no effect on SRTT/RTO because of Karn's check.
Signed-off-by: NKenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Tested-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even if we make use of classifier and actions from the egress
path, we're going into handle_ing() executing additional code
on a per-packet cost for ingress qdisc, just to realize that
nothing is attached on ingress.

Instead, this can just be blinded out as a no-op entirely with
the use of a static key. On input fast-path, we already make
use of static keys in various places, e.g. skb time stamping,
in RPS, etc. It makes sense to not waste time when we're assured
that no ingress qdisc is attached anywhere.

Enabling/disabling of that code path is being done via two
helpers, namely net_{inc,dec}_ingress_queue(), that are being
invoked under RTNL mutex when a ingress qdisc is being either
initialized or destructed.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thomas Graf says:

====================
Bring sizeof(net_device) down to < 2K bytes

The size of struct net_device crossed the 2K boundary a while ago which
is a waste in combination with many net namespaces. This series brings
the size of struct net_device down to well below 2K in total size with
a typical configuration. Some reserves a several holes leave room for
further expansion.

Before:
/* size: 2176, cachelines: 34, members: 121 */

After:
/* size: 1984, cachelines: 31, members: 120 */
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some trivial reorders while preserving the RX/TX cache lines
split to fill a couple of holes.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e1000e is the only driver requiring pm_qos_req, instead of causing
every device to waste up to 240 bytes. Allocate it for the specific
driver.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a new rtnl or xfrm command is added, this part of the code is frequently
missing. Let's help the developer with a build time test.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-04-11

This series contains updates to iflink, ixgbe and ixgbevf.

The entire set of changes come from Vlad Zolotarov to ultimately add
the ethtool ops to VF driver to allow querying the RSS indirection table
and RSS random key.

Currently we support only 82599 and x540 devices.  On those devices, VFs
share the RSS redirection table and hash key with a PF.  Letting the VF
query this information may introduce some security risks, therefore this
feature will be disabled by default.

The new netdev op allows a system administrator to change the default
behaviour with "ip link set" command.  The relevant iproute2 patch has
already been sent and awaits for this series upstream.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cong Wang says:

====================
fou: some fixes and updates

Patch 1~3 fix some minor bugs in net/ipv4/fou.c, the only
thing I am not sure is if it's too late to change the
byte order of FOU_ATTR_PORT, if so we have to fix iproute2
instead of kernel.

Patch 4~5 add some new features to make it complete.

v2: make fou->port be16 too
====================
Acked-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also convert the spinlock to a mutex.

Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

udp_config.local_udp_port is be16. And iproute2 passes
network order for FOU_ATTR_PORT.

This doesn't fix any bug, just for consistency.

Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>