ICH4-L is a variant of ICH4 lacking USB2 functionality and with some
different device IDs.

It is documented in Intel specification update 290745-025, currently
at <http://www.intel.com/assets/pdf/specupdate/290745.pdf>, and is
included in the device ID table for piix.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

... since, of course, it's not used outside this driver.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Intel IDE-R devices are part of the Intel AMT management setup. They don't
have any special configuration registers or settings so the ata_generic
driver will support them fully.

Rather than add a huge table of IDs for each chipset and keep sending in
new ones this patch autodetects them.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reorder structure ata_queued_cmd to remove 8 bytes of alignment padding
on 64 bit builds & therefore reduce the size of structure ata_port by
256 bytes.

Overall this will have little impact, other than reducing the amount of
memory that is cleared when allocating ata_ports.
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Until now identifying that a device supports WRITE SAME(16) with the
UNMAP bit set has been black magic.  Implement support for the SBC-3
Thin Provisioning VPD page and set the TPWS bit.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Now that libata provides proper cross-port EH exclusion.  The SIDPR
locking added by commit 213373cf (ata_piix: fix locking around SIDPR
access) is no longer necessary.  Remove it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

In libata, the non-EH code paths should always take and release
ap->lock explicitly when accessing hardware or shared data structures.
However, once EH is active, it's assumed that the port is owned by EH
and EH methods don't explicitly take ap->lock unless race from irq
handler or other code paths are expected.  However, libata EH didn't
guarantee exclusion among EHs for ports of the same host.  IOW,
multiple EHs may execute in parallel on multiple ports of the same
controller.

In many cases, especially in SATA, the ports are completely
independent of each other and this doesn't cause problems; however,
there are cases where different ports share the same resource, which
lead to obscure timing related bugs such as the one fixed by commit
213373cf (ata_piix: fix locking around SIDPR access).

This patch implements exclusion among EHs of the same host.  When EH
begins, it acquires per-host EH ownership by calling ata_eh_acquire().
When EH finishes, the ownership is released by calling
ata_eh_release().  EH ownership is also released whenever the EH
thread goes to sleep from ata_msleep() or explicitly and reacquired
after waking up.

This ensures that while EH is actively accessing the hardware, it has
exclusive access to it while allowing EHs to interleave and progress
in parallel as they hit waiting stages, which dominate the time spent
in EH.  This achieves cross-port EH exclusion without pervasive and
fragile changes while still allowing parallel EH for the most part.

This was first reported by yuanding02@gmail.com more than three years
ago in the following bugzilla.  :-)

  https://bugzilla.kernel.org/show_bug.cgi?id=8223Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reported-by: yuanding02@gmail.com
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration.  These will be used to implement EH exclusion.

This patch doesn't cause any behavior difference.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Now that DIPM can be used independently from HIPM, ata_piix can
support LPM too.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Port multipliers can do DIPM on fan-out links fine.  Implement support
for it.  Tested w/ SIMG 57xx and marvell PMPs.  Both the host and
fan-out links enter power save modes nicely.

SIMG 37xx and 47xx report link offline on SStatus causing EH to detach
the devices.  Blacklisted.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The current LPM implementation has the following issues.

* Operation order isn't well thought-out.  e.g. HIPM should be
  configured after IPM in SControl is properly configured.  Not the
  other way around.

* Suspend/resume paths call ata_lpm_enable/disable() which must only
  be called from EH context directly.  Also, ata_lpm_enable/disable()
  were called whether LPM was in use or not.

* Implementation is per-port when it should be per-link.  As a result,
  it can't be used for controllers with slave links or PMP.

* LPM state isn't managed consistently.  After a link reset for
  whatever reason including suspend/resume the actual LPM state would
  be reset leaving ap->lpm_policy inconsistent.

* Generic/driver-specific logic boundary isn't clear.  Currently,
  libahci has to mangle stuff which libata EH proper should be
  handling.  This makes the implementation unnecessarily complex and
  fragile.

* Tied to ALPM.  Doesn't consider DIPM only cases and doesn't check
  whether the device allows HIPM.

* Error handling isn't implemented.

Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense.  This patch reimplements
LPM support.

* The new implementation is per-link.  The target policy is still
  port-wide (ap->target_lpm_policy) but all the mechanisms and states
  are per-link and integrate well with the rest of link abstraction
  and can work with slave and PMP links.

* Core EH has proper control of LPM state.  LPM state is reconfigured
  when and only when reconfiguration is necessary.  It makes sure that
  LPM state is reset when probing for new device on the link.
  Controller agnostic logic is now implemented in libata EH proper and
  driver implementation only has to deal with controller specifics.

* Proper error handling.  LPM config failure is attributed to the
  device on the link and LPM is disabled for the link if it fails
  repeatedly.

* ops->enable/disable_pm() are replaced with single ops->set_lpm()
  which takes @policy and @hints.  This simplifies driver specific
  implementation.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Link power management is about to be reimplemented.  Prepare for it.

* Implement sata_link_scr_lpm().

* Drop static from ata_dev_set_feature() and make it available to
  other libata files.

* Trivial whitespace adjustments.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm.  This patch cleans up lpm related symbols
and sysfs show/store functions as follows.

* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
  MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
  ATA_LPM_{MIN|MAX|MED}_POWER.

* Pre/postfixes are unified to lpm.

* sysfs show/store functions for link_power_management_policy were
  curiously named get/put and unnecessarily complex.  Renamed to
  show/store and simplified.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This build error showed up in linux-next tag next-20100820 for ia64:

WARNING: vmlinux.o(.init.text+0x4a952): Section mismatch in reference from the function ata_init() to the function .exit.text:ata_sff_exit()
The function __init ata_init() references
a function __exit ata_sff_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
ata_sff_exit() so it may be used outside an exit section.

Sure enough, dropping the __exit fixes the problem.
Signed-off-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This change enables my x86 machine to recognize and talk to a
"Native 4K" SATA device.

When I started working on this, I didn't know Matthew Wilcox had
posted a similar patch 2 years ago:
  http://git.kernel.org/?p=linux/kernel/git/willy/ata.git;a=shortlog;h=refs/heads/ata-large-sectors

Gwendal Grignou pointed me at the the above code and small portions of
this patch include Matthew's work. That's why Mathew is first on the
"Signed-off-by:". I've NOT included his use of a bitmap to determine
512 vs Native for ATA command block size - just used a simple table.
And bugs are almost certainly mine.

Lastly, the patch has been tested with a native 4K 'Engineering
Sample' drive provided by Hitachi GST.
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: NGrant Grundler <grundler@google.com>
Reviewed-by: NGwendal Grignou <gwendal@google.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Currently, sata_fsl, mv and nv call ata_qc_complete() multiple times
from their interrupt handlers to indicate completion of NCQ commands.
This limits the visibility the libata core layer has into how commands
are being executed and completed, which is necessary to support IRQ
expecting in generic way.  libata already has an interface to complete
multiple commands at once - ata_qc_complete_multiple() which ahci and
sata_sil24 already use.

This patch updates the three drivers to use ata_qc_complete_multiple()
too and updates comments on ata_qc_complete[_multiple]() regarding
their usages with NCQ completions.  This change not only provides
better visibility into command execution to the core layer but also
simplifies low level drivers.

* sata_fsl: It already builds done_mask.  Conversion is straight
  forward.

* sata_mv: mv_process_crpb_response() no longer checks for illegal
  completions, it just returns whether the tag is completed or not.
  mv_process_crpb_entries() builds done_mask from it and passes it to
  ata_qc_complete_multiple() which will check for illegal completions.

* sata_nv adma: Similar to sata_mv.  nv_adma_check_cpb() now just
  returns the tag status and nv_adma_interrupt() builds done_mask from
  it and passes it to ata_qc_complete_multiple().

* sata_nv swncq: It already builds done_mask.  Drop unnecessary
  illegal transition checks and call ata_qc_complete_multiple().

In the long run, it might be a good idea to make ata_qc_complete()
whine if called when multiple NCQ commands are in flight.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.
Signed-off-by: NGwendal Grignou <gwendal@google.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: O32 compat/N32: Fix to use compat syscall wrappers for AIO syscalls.
  MAINTAINERS: Change list for ioc_serial to linux-serial.
  SERIAL: ioc3_serial: Return -ENOMEM on memory allocation failure
  MIPS: jz4740: Fix Kbuild Platform file.
  MIPS: Repair Kbuild make clean breakage.

If the host is slow in reading data or doesn't read data at all,
blocking write calls not only blocked the program that called write()
but the entire guest itself.

To overcome this, let's not block till the host signals it has given
back the virtio ring element we passed it.  Instead, send the buffer to
the host and return to userspace.  This operation then becomes similar
to how non-blocking writes work, so let's use the existing code for this
path as well.

This code change also ensures blocking write calls do get blocked if
there's not enough room in the virtio ring as well as they don't return
-EAGAIN to userspace.
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
CC: stable@kernel.org
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] bsg: fix incorrect device_status value
  [SCSI] Fix VPD inquiry page wrapper

* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: Fix fs/gs reload oops with invalid ldt

[Ralf: Michel's original patch only fixed N32; I replicated the same fix
for O32.]
Signed-off-by: NMichel Thebeau <michel.thebeau@windriver.com>
Cc: paul.gortmaker@windriver.com
Cc: bruce.ashfield@windriver.com
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

IOC3 is also being used on SGI MIPS systems but this particular driver is
only being used on IA64 systems so linux-mips made no sense as a list.  Pat
also thinks linux-serial@vger.kernel.org is the better list.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In this code, 0 is returned on memory allocation failure, even though other
failures return -ENOMEM or other similar values.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression ret;
expression x,e1,e2,e3;
@@

ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
To: Pat Gefre <pfg@sgi.com>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1704/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The platform specific files should be included via the platform-y
variable.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Patchwork: https://patchwork.linux-mips.org/patch/1719/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When running make clean, Kbuild doesn't process the .config file, so nothing
generates a platform-y variable.  We can get it to descend into the platform
directories by setting $(obj-).

The dec Platform file was unconditionally setting platform-, obliterating
its previous contents and preventing some directories from being cleaned.
This is change to an append operation '+=' to allow cavium-octeon to be
cleaned.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/1718/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: avivo cursor workaround applies to evergreen as well

kvm reloads the host's fs and gs blindly, however the underlying segment
descriptors may be invalid due to the user modifying the ldt after loading
them.

Fix by using the safe accessors (loadsegment() and load_gs_index()) instead
of home grown unsafe versions.

This is CVE-2010-3698.

KVM-Stable-Tag.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Enable ISA_DMA_API config to fix build failure
  MIPS: 32-bit: Fix build failure in asm/fcntl.h
  MIPS: Remove all generated vmlinuz* files on "make clean"
  MIPS: do_sigaltstack() expects userland pointers
  MIPS: Fix error values in case of bad_stack
  MIPS: Sanitize restart logics
  MIPS: secure_computing, syscall audit: syscall number should in r2, not r0.
  MIPS: Don't block signals if we'd failed to setup a sigframe

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: evdev - fix EVIOCSABS regression
  Input: evdev - fix Ooops in EVIOCGABS/EVIOCSABS

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: ohci: fix TI TSB82AA2 regression since 2.6.35

This patch reverts the driver to enabling/disabling the NFC interrupt
mask rather than enabling/disabling the system interrupt.  This cleans
up the driver so that it doesn't rely on interrupts being disabled
within the interrupt handler.

For i.MX21 we keep the current behaviour, that is calling
enable_irq/disable_irq_nosync to enable/disable interrupts.  This patch
is based on earlier work by John Ogness.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NJohn Ogness <john.ogness@linutronix.de>
Tested-by: NJohn Ogness <john.ogness@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus/i2c/2636-rc8' of git://git.fluff.org/bjdooks/linux:
  i2c-imx: do not allow interruptions when waiting for I2C to complete
  i2c-davinci: Fix TX setup for more SoCs

* fixes:
  v4l1: fix 32-bit compat microcode loading translation
  De-pessimize rds_page_copy_user

Add ISA_DMA_API config item and select it when GENERIC_ISA_DMA enabled.
This fixes build failure on allmodconfig like following:

  CC      sound/isa/es18xx.o
sound/isa/es18xx.c: In function 'snd_es18xx_playback1_prepare':
sound/isa/es18xx.c:501:9: error: implicit declaration of function 'snd_dma_program'
sound/isa/es18xx.c: In function 'snd_es18xx_playback_pointer':
sound/isa/es18xx.c:818:3: error: implicit declaration of function 'snd_dma_pointer'
make[3]: *** [sound/isa/es18xx.o] Error 1
make[2]: *** [sound/isa/es18xx.o] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1717/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  CC      security/integrity/ima/ima_fs.o
In file included from linux/include/linux/fcntl.h:4:0,
                 from linux/security/integrity/ima/ima_fs.c:18:
linux/arch/mips/include/asm/fcntl.h:63:2: error: expected specifier-qualifier-list before 'off_t'
make[3]: *** [security/integrity/ima/ima_fs.o] Error 1
make[2]: *** [security/integrity/ima/ima_fs.o] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1715/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

[Ralf: I changed the patch to explicitly list all files to be deleted out
of paranoia.]
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1590/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

o32 compat does the right thing, native and n32 compat do not...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1700/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>