Some PCI devices fail if their standard configuration registers are
restored twice in a row.  Prevent this from happening by making
pci_restore_state() clear the saved_state flag of the device right
after the device's standard configuration registers have been
populated with the previously saved values.

Simplify PCI PM callbacks by removing the direct clearing of
state_saved from them, as it shouldn't be necessary any more (except
in pci_pm_thaw(), where it has to be cleared, so that the values saved
during the "freeze" phase of hibernation are not used later by mistake).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Currently pci_pm_resume() always returns 0, which makes the error
variable defined in there a bit pointless.  Make pci_pm_resume()
return error codes obtained from drivers' callbacks.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Convert quirk printks to dev_printk().
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
CC: Olaf Dabrunz <od@suse.de>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

After commit c82f63e4
(PCI: check saved state before restore) pcie_portdrv_slot_reset()
may not work correctly if dev->error_state is equal to
pci_channel_io_frozen, because dev->state_saved need not be set at
that time.  Fix this issue by setting dev->state_saved before
pci_restore_state() is called in pcie_portdrv_slot_reset().
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

acpi_pci_detect_ejectable() goes through effort to convert its
struct pci_bus arg to an acpi_handle, but every time we use this
interface, we already have the handle available.

So let's just use the handle instead of converting back and forth.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Instead of constantly evaluating _ADR and _SEG over and over again,
let's simplify our lives by using:

	acpi_pci_find_root() for root bridges
	acpi_get_pci_dev() for p2p bridges

This change eliminates some copy 'n paste code and also allows us
to simplify some internal interfaces.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remove unused port_data variable left over from the MCH hotplug quirk
cleanup.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some PCI devices (not PCI Express), like PCI add-on cards, can
generate PME#, but they don't have any special platform wake-up
support.  For this reason, even if they generate PME# to wake up the
system from a sleep state, wake-up events are not generated by the
platform.

It turns out that, at least on some systems, PCI bridges and the PCI
host bridge have ACPI GPEs associated with them that, if enabled to
generate wake-up events, allow the system to wake up if one of the
add-on devices asserts PME# while the system is in a sleep state.
Following this observation, if a PCI device without direct ACPI
wake-up support is prepared to wake up the system during a transition
into a sleep state (eg. suspend to RAM), try to configure the bridges
on the path from the device to the root bridge to wake-up the system.
Reviewed-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The wakeup.prepared flag is used for marking devices that have the
wake-up power already enabled, so that the wake-up power is not
enabled twice in a row for the same device.  This assumes, however,
that device wake-up power will only be enabled once, while the device
is being prepared for a system-wide sleep transition, and the second
attempt is made by acpi_enable_wakeup_device_prep().

With the upcoming PCI wake-up rework this assumption will not hold
any more for PCI bridges and the root bridge whose wake-up power
may be enabled as a result of wake-up enable propagation from other
devices (eg. add-on devices that are not associated with any GPEs).
Thus, there may be many attempts to enable wake-up power on a PCI
bridge or the root bridge during a system power state transition
and it's better to replace wakeup.prepared with a reference counter.
Reviewed-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Introduce a new PCI device flag, wakeup_prepared, to prevent PCI
wake-up preparation code from being executed twice in a row for the
same device and for the same purpose.
Reviewed-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Move a debug message from acpi_pci_sleep_wake() to
acpi_pm_device_sleep_wake() and use the standard dev_*() macros
in there.
Reviewed-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Rework the PCI wake-up code so that it's easier to read without
changing the functionality.
Reviewed-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Stanse found a pci reference leak in quirk_amd_nb_node.
Instead of putting nb_ht, there is a put of dev passed as
an argument.

http://stanse.fi.muni.cz/Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In general a BIOS may goof or we may hotplug in a hotplug controller.
In either case the kernel needs to reserve resources for plugging
in more devices in the future instead of creating a minimal resource
assignment.

We already do this for cardbus bridges I am just adding a variant
for pcie bridges.

v2: Make testing for pcie hotplug bridges based on a flag.

    So far we only set the flag for pcie but a header_quirk
    could easily be added for the non-standard pci hotplug
    bridges.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.

Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.

The re-running of this fixup after pci hotplug happens below these
devices is totally bogus.  All of the state we change is pure software
state and we don't change the hardware at all.  Which means hotplug on
the lower devices doesn't have a chance to change this state.  So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.

I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch is required not to lost error records by action invoked on
error recovery, such as slot reset etc.

Following sample (real machine + dummy record injected by aer-inject)
shows that record of 28:00.1 could not be retrieved by recovery of 28:00.0:

- Before:

pcieport-driver 0000:00:02.0: AER: Multiple Uncorrected (Non-Fatal) error received: id=2801
e1000e 0000:28:00.0: PCIE Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=2800(Receiver ID)
e1000e 0000:28:00.0:   device [8086:1096] error status/mask=00001000/00100000
e1000e 0000:28:00.0:    [12] Poisoned TLP           (First)
e1000e 0000:28:00.0:   TLP Header: 00000000 00000001 00000002 00000003
e1000e 0000:28:00.0: broadcast error_detected message
e1000e 0000:28:00.0: broadcast slot_reset message
e1000e 0000:28:00.0: setting latency timer to 64
e1000e 0000:28:00.0: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.1: setting latency timer to 64
e1000e 0000:28:00.1: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.0: broadcast resume message
e1000e 0000:28:00.0: AER driver successfully recovered
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX

- After:

pcieport-driver 0000:00:02.0: AER: Multiple Uncorrected (Non-Fatal) error received: id=2801
e1000e 0000:28:00.0: PCIE Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=2800(Receiver ID)
e1000e 0000:28:00.0:   device [8086:1096] error status/mask=00001000/00100000
e1000e 0000:28:00.0:    [12] Poisoned TLP           (First)
e1000e 0000:28:00.0:   TLP Header: 00000000 00000001 00000002 00000003
e1000e 0000:28:00.1: PCIE Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=2801(Receiver ID)
e1000e 0000:28:00.1:   device [8086:1096] error status/mask=00081000/00100000
e1000e 0000:28:00.1:    [12] Poisoned TLP           (First)
e1000e 0000:28:00.1:    [19] ECRC
e1000e 0000:28:00.1:   TLP Header: 00000000 00000001 00000002 00000003
e1000e 0000:28:00.1:   Error of this Agent(2801) is reported first
e1000e 0000:28:00.0: broadcast error_detected message
e1000e 0000:28:00.0: broadcast slot_reset message
e1000e 0000:28:00.0: setting latency timer to 64
e1000e 0000:28:00.0: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.1: setting latency timer to 64
e1000e 0000:28:00.1: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.0: broadcast resume message
e1000e 0000:28:00.0: AER driver successfully recovered
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use dev_printk like format.

Sample (real machine + dummy error injected by aer-inject):

- Before:

+------ PCI-Express Device Error ------+
Error Severity          : Corrected
PCIE Bus Error type     : Data Link Layer
Bad TLP                 :
Receiver ID             : 2800
VendorID=8086h, DeviceID=1096h, Bus=28h, Device=00h, Function=00h
+------ PCI-Express Device Error ------+
Error Severity          : Corrected
PCIE Bus Error type     : Data Link Layer
Bad TLP                 :
Bad DLLP                :
Receiver ID             : 2801
VendorID=8086h, DeviceID=1096h, Bus=28h, Device=00h, Function=01h
Error of this Agent(2801) is reported first

- After:

pcieport-driver 0000:00:02.0: AER: Multiple Corrected error received: id=2801
e1000e 0000:28:00.0: PCIE Bus Error: severity=Corrected, type=Data Link Layer, id=2800(Receiver ID)
e1000e 0000:28:00.0:   device [8086:1096] error status/mask=00000040/00000000
e1000e 0000:28:00.0:    [ 6] Bad TLP
e1000e 0000:28:00.1: PCIE Bus Error: severity=Corrected, type=Data Link Layer, id=2801(Receiver ID)
e1000e 0000:28:00.1:   device [8086:1096] error status/mask=000000c0/00000000
e1000e 0000:28:00.1:    [ 6] Bad TLP
e1000e 0000:28:00.1:    [ 7] Bad DLLP
e1000e 0000:28:00.1:   Error of this Agent(2801) is reported first
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Compact struct and codes.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Cleanup.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Multiple bits might be set in the Uncorrectable Error Status
register.  But aer_print_error_source() only report a error of
the lowest bit set in the error status register.

So print strings for all bits unmasked and set.

And check First Error Pointer to mark the error occured first.
This FEP is not valid when the corresponing bit of the Uncorrectable
Error Status register is not set, or unimplemented or undefined.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

ERR_{,UN}CORRECTABLE_ERROR_MASK are set of error bits which linux know,
set of PCI_ERR_COR_* and PCI_ERR_UNC_* defined in linux/pci_regs.h.
This masks make aerdrv not to report errors of unknown bit, while aerdrv
have ability to report such undefined errors as "Unknown Error Bit %2d".

OTOH aerdrv_errprint does not have any check of setting in mask register.
So it could report masked wrong error by finding bit in status without
knowing that the bit is masked in the mask register.

This patch changes aerdrv to use mask state in mask register propely
instead of defined/hardcoded ERR_{,UN}CORRECTABLE_ERROR_MASK.
This change prevents aerdrv from reporting masked error, and also enable
reporting unknown errors.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The static buffer errmsg_buff[] is used only for building error
message in fixed format, and is protected by a spinlock.

This patch removes this buffer and the spinlock.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The flag AER_MULTI_ERROR_VALID_FLAG in info->flag does mean that the
root port receives multiple error messages.  Error messages can be
posted from different devices, so it does not mean that each reported
device has multiple errors.

If there are multiple error devices and the root port has valid error
source ID, it would be nice to report which device is the error source
reported first.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In case of multiple errors, struct aer_err_info would be reused among
all reported devices.  So the info->status should be initialized before
recycled.  Otherwise error of one device might be reported as the error
of another device.  Also info->flags has similar problem on reporting
TLP header.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Definitions of MASK macros in aerdrv_errprint.c are tricky and unsafe.

For example, AER_AGENT_TRANSMITTER_MASK(_sev, _stat) does work like:
  static inline func(int _sev, int _stat)
  {
    if (_sev == AER_CORRECTABLE)
      return (_stat & (PCI_ERR_COR_REP_ROLL|PCI_ERR_COR_REP_TIMER));
    else
      return (_stat & PCI_ERR_COR_REP_ROLL);
  }
In case of else path here, for uncorrectable errors, testing bits in
_stat by PCI_ERR_COR_* does not make sense because _stat should have only
PCI_ERR_UNC_* bits originated in uncorrectable error status register.
But at this time this is safe because uncorrectable error using bit
position same to PCI_ERR_COR_REP_ROLL(= bit position 8) is not defined.
Likewise, AER_AGENT_COMPLETER_MASK is always PCI_ERR_UNC_COMP_ABORT but
it works because bit 15 of correctable error status is not defined.

It means that these MASK macros will turn to be wrong once if new error
is defined. (In fact, bit 15 of correctable is now defined in PCIe 2.1)

This patch changes these MASK macros to be more strict, not to return
PCI_ERR_COR_* bits for uncorrectable error status and vise versa.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add workaround macro to reduce the number of checkpatch warning:
 WARNING: printk() should include KERN_ facility level

Before:
  total: 0 errors, 10 warnings, 247 lines checked
After:
  total: 0 errors, 1 warnings, 243 lines checked
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Before:
 drivers/pci/pcie/aer/aer_inject.c
  total: 4 errors, 4 warnings, 473 lines checked
 drivers/pci/pcie/aer/aerdrv.c
  total: 5 errors, 2 warnings, 333 lines checked
 drivers/pci/pcie/aer/aerdrv.h
  total: 1 errors, 0 warnings, 139 lines checked
 drivers/pci/pcie/aer/aerdrv_core.c
  total: 4 errors, 3 warnings, 872 lines checked
 drivers/pci/pcie/aer/aerdrv_errprint.c
  total: 12 errors, 11 warnings, 248 lines checked

After:
 drivers/pci/pcie/aer/aer_inject.c
  total: 0 errors, 0 warnings, 466 lines checked
 drivers/pci/pcie/aer/aerdrv.c
  total: 0 errors, 0 warnings, 335 lines checked
 drivers/pci/pcie/aer/aerdrv.h
  total: 0 errors, 0 warnings, 139 lines checked
 drivers/pci/pcie/aer/aerdrv_core.c
  total: 0 errors, 0 warnings, 869 lines checked
 drivers/pci/pcie/aer/aerdrv_errprint.c
  total: 0 errors, 10 warnings, 247 lines checked
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add ids module parameter which allows specifying initial IDs for the
pci-stub driver.  When built into the kernel, pci-stub is linked
before any real pci drivers and by setting up IDs from initialization
it can prevent built-in drivers from attaching to specific devices.

While at it, make pci_stub_probe() print out about devices it grabbed
to weed out "but my controller isn't being probed" bug reports.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Separate out pci_add_dynid() from store_new_id() and export it so that
in-kernel code can add PCI IDs dynamically.  As the function will be
available regardless of HOTPLUG, put it and pull pci_free_dynids()
outside of CONFIG_HOTPLUG.

This will be used by pci-stub to initialize initial IDs via module
param.

While at it, remove bogus get_driver() failure check.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add support for PCI-E 5.0 GT/s in max_bus_speed and cur_bus_speed.
Reviewed-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix typo in PCI-E link speed.
Reviewed-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The L0s state can be managed separately for each direction (upstream
direction and downstream direction) of the link. But in the current
implementation, those are mixed up. With this patch, L0s for each
direction are managed separately.

To maintain three states (upstream direction L0s, downstream L0s and
L1), 'aspm_support', 'aspm_enabled', 'aspm_capable', 'aspm_disable'
and 'aspm_default' fields in struct pcie_link_state are changed to
3-bit from 2-bit. The 'latency' field is separated to two 'latency_up'
and 'latency_dw' fields to maintain exit latencies for each direction
of the link. For L0, 'latency_up.l0' and 'latency_dw.l0' are used to
configure upstream direction L0s and downstream direction L0s
respectively. For L1, larger value of 'latency_up.l1' and
'latency_dw.l1' is considered as L1 exit latency.
Acked-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In the current implementation, ASPM L0s/L1 is disabled for all links
in the hierarchy if one of the link doesn't meet latency requirement.
But we can partially enable ASPM L0s/L1 on sub-tree in the hierarchy.
This patch allows partial L0s/L1 enablement in the hierarchy. And it
also reduce the calculation cost of ASPM configuration very much.

In the previous implementation, all links were enabled with the same
state. With this patch, enabled state for each link is determined
simply as follows (the 'requested' is from policy_to_aspm_state()).

    enabled = requested & (link->aspm_capable & link->aspm_disable)
Acked-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Introduce 'aspm_capable' field to maintain the capable ASPM setting of
the link. By the 'aspm_capable', we don't need to recheck latency
every time ASPM policy is changed.

Each bit in 'aspm_capable' is associated to ASPM state (L0S/L1). The
bit is set if the associated ASPM state is supported by the link and
it satisfies the latency requirement (i.e. exit latency < endpoint
acceptable latency). The 'aspm_capable' is updated when

  - an endpoint device is added (boot time or hot-plug time)
  - an endpoint device is removed (hot-unplug time)
  - PCI power state is changed.
Acked-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Introduce 'aspm_disable' flag to manage disabled ASPM state more
robust way.
Acked-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix possible NULL dereference in pcie_aspm_exit_link_state(). This
patch also cleanup some code.
Acked-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remove the following check in __pcie_aspm_config_link() because it
nerver be true.
Acked-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We must not clear bits in 'aspm_enabled' using 'aspm_support', or
'aspm_enabled' and 'aspm_default' might be different from the actual
state. In addtion, 'aspm_default' should be intialized even if
'aspm_support' is 0.
Acked-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch adds the most recent additions to the list of 82576 device IDs
to the list of devices needing the SR-IOV quirk.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Document the new VGA arbiter.
Signed-off-by: NTiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>