According to the ASPEED datasheet, gigabit speeds require a clock of
100MHz or higher. Other speeds require 25MHz or higher. This patch
configures a 100MHz clock if the system has a direct-attached
PHY, or 25MHz if the system is running NC-SI which is limited to 100MHz.

There appear to be no other upstream users of the FTGMAC100 driver it is
hard to know the clocking requirements of other platforms. Therefore a
conservative approach was taken with enabling clocks. If the platform is
not ASPEED, both requesting the clock and configuring the speed is
skipped.
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Tested-by: NAndrew Jeffery <andrew@aj.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Formerly, IPIP entries were created lazily by next hops that referenced
an offloadable IP-in-IP netdevice. However now that they are created
eagerly as a reaction to events on such netdevices, the reference
counting is useless. Hence drop it.

The routes whose next hops reference an offloaded IP-in-IP netdevice
actually linger around a bit after their device is unregistered.
However, mlxsw_sp_ipip_entry_destroy() also destroys the backing
loopback, and mlxsw_sp_rif_destroy() transitively (via
mlxsw_sp_nexthop_rif_gone_sync()) calls mlxsw_sp_nexthop_ipip_fini(),
which unlinks the IPIP entry from a next hop. Thus no dangling pointers
are left behind for the brief window after netdevice is gone, but routes
not yet.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPIP entries are created as soon as an offloadable device is created.
That means that when such a device is later moved to a different VRF,
the loopback device that backs the tunnel is wrong.

Thus when an offloadable encapsulating netdevice moves from one VRF to
another, make sure that the loopback is updated as necessary.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current code for offloading IP-in-IP tunneling assumes that there is no
decap without encap. But that's never true for IPv6 overlays, and is not
true for IPv4 ones either, if net.ipv4.conf.*.rp_filter is unset.

To support decap-only tunnels, an IPIP entry is now created as soon as
an offloadable tunneling device is created. When that netdevice is up'd,
a decap route is looked up and possibly offloaded. Thus decap is not
handled implicitly as part of mlxsw_sp_ipip_entry_get() call anymore,
but needs to be done explicitly after the get, if desired.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far, all netdevice notifications that the driver cared about were
related to its own ports, and mlxsw_sp could be retrieved from the
netdevice's private data. For IP-in-IP offloading however, the driver
cares about events on foreign netdevices, and getting at mlxsw_sp or
router data structures from the handler is inconvenient.

Therefore move the netdevice notifier blocks from global scope to struct
mlxsw_sp to allow retrieval from the notifier block pointer itself.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The notifier cause a link error when NET_DSA is a loadable
module:

drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_remove':
bcmsysport.c:(.text+0x1582): undefined reference to `unregister_dsa_notifier'
drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_probe':
bcmsysport.c:(.text+0x278d): undefined reference to `register_dsa_notifier'

This adds a dependency that forces the systemport driver to be
a loadable module as well when that happens, but otherwise
allows it to be built normally when DSA is either built-in or
completely disabled.

Fixes: d1565763 ("net: systemport: Establish lower/upper queue mapping")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify baycom driver to use the new parallel port device model.
Signed-off-by: NSudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes custom flag handling.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the pkt_type to PACKET_HOST only if the destination MAC
address matches on the on the source based macvlan. It didn't make sense to
be updating broadcast, multicast, and non-local destined frames with
PACKET_HOST.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch intoduces a slight adjustment for macvlan to address the fact
that in source mode I was seeing two copies of any packet addressed to the
macvlan interface being delivered where there should have been only one.

The issue appears to be that one copy was delivered based on the source MAC
address and then the second copy was being delivered based on the
destination MAC address. To fix it I am just treating a unicast address
match as though it is not a match since source based macvlan isn't supposed
to be matching based on the destination MAC anyway.

Fixes: 79cf79ab ("macvlan: add source mode")
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tx_table is part of the private data of kernel net_device. It is only
zero-ed out when allocating net_device.

We may recreate netvsc_device w/o recreating net_device, so the private
netdev data, including tx_table, are not zeroed. It may contain channel
numbers for the older netvsc_device.

This patch adds initialization of tx_table each time we recreate
netvsc_device.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the variable name: tx_send_table
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename this variable because it is the Receive indirection
table.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The break statement for the Macronix case is missing and will
fall through to the Winbond case and re-assign the size setting.
Fix this by adding the missing break statement.  Also correctly
indent the return statements.

Detected by CoverityScan, CID#1458020 ("Missing break in switch")

Fixes: 96ac18f1 ("cxgb4: Add support for new flash parts")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Collect SGE, PCIE, PM, UP CIM, MA and HMA dumps.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Try to access TP indirect registers via firmware first.  If this fails,
fallback and access them directly.  This ensures that driver and
firmware do not conflict each other while accessing the TP indirect
registers.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Collect firmware mbox and device logs before collecting the rest of
the hardware dumps to snap the firmware state before the mailbox logs
are updated by other hardware dumps.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Collect EDC0 and EDC1 memory dump.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add base to collect dump entities.  Collect register dump and
update template header accordingly.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement operations to set/get dump data via ethtool.  Also add
template header that precedes dump data, which helps in decoding
and extracting the dump data.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Today's -next build encountered an error due to a missing definition of
WARN_ON(), caused by some header reorganization removing an implicit
inclusion of linux/bug.h.  Fix this with an explicit inclusion.
Signed-off-by: NMark Brown <broonie@kernel.org>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The .set_addr function does nothing, remove the dsa_loop implementation
before getting rid of it completely in DSA.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As for mv88e6xxx, setup the switch from within the mv88e6060 driver with
a random MAC address, and remove the .set_addr implementation.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".

If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.

The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An Ethernet switch may support having a MAC address, which can be used
as the switch's source address in transmitted full-duplex Pause frames.

If a DSA switch supports the related .set_addr operation, the DSA core
sets the master's MAC address on the switch. This won't make sense
anymore in a multi-CPU ports system, because there won't be a unique
master device assigned to a switch tree.

Instead, setup the switch from within the Marvell driver with a random
MAC address, and remove the .set_addr implementation.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resources such as FT, QPN HT and mdev resources should be allocated
only by parent netdev. Shared resources are allocated and freed by the
parent interface since the parent is always present and created
before the IPoIB PKEY sub-interface.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>

Similar to VLAN interfaces child interfaces have limited ethtool
support. In current code the main limitation that does not
allow child interface ethtool configuration is due to shared
resources which are managed by the parent.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>

Child interface ndos will be called to support child interface
specific behaviour.

ndo_init flow:
-Acquire shared QPN to net-device HT from parent
-Continue with the same flow as parent interface

ndo_open flow:
-Initialize child underlay QP and connect to shared FT
-Create child send TIS
-Open child send channels
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>

Child interface profile will be called to support child interface
specific behaviour. The child code is sparse compared to the parent
since the RX channels are shared between the interfaces.
Creating a septate profile for child and parent will make a smother
code with a better ability for future expansion.
The profile stuct is exposed to the parent using a getter function.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>

This change is needed for PKEY support, since the RQs are shared
between the child interface and the parent. The parent is responsible
for NAPI and the precessing of RX completions. Using the dqpn in the
completion descriptor we set the corresponding child IPoIB netdevice
on the SKB.
The mapping between the dqpn and the netdevice is done using a HT,
each mlx5 IPoIB interface registers its mapping on creation.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>

Added a function to set PKEY index to IPoIB device driver using the
already present set_id function. PKEY index is attached to the QP
during state modification.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>

Previous support allowed connecting only a single QPN to the FT.
Now using a linked list multiple QPNs can be attached to the same FT.

Supporting attaching multiple underlay QPs is required for PKEY
support in which child and parent share the same FT.

The actual attaching/detaching FW commands will be called inside the
function symmetrically.

This change requires a change in IPoIB open and close functions, the
attaching/detaching to/from the FT is done each time we open/close.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

During the creation of the underlay QP the PKEY index is unknown, the
PKEY index is known only when calling ndo_open.
PKEY index attached to the QP during state modification.

Splitting the functions will also make the code symmetric and more
readable. This split is also required for later PKEY support to be
called with the PKEY index during ndo_open.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

PTP code is moved to core section of mlx5 driver in order to share
it between ethernet and infiniband. This movement involves the following
changes:
- Change mlx5e_ prefix to be mlx5_
- Add clock structs to Core
- Add clock object to mlx5_core_dev
- Call Init/Uninit clock from core init/cleanup
- Rename mlx5e_tstamp to be mlx5_clock
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NEitan Rabin <rabin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

en_clock.c renamed clock.c and moved to lib/ as first step
towards relocating code to core part of the driver to allow
sharing between Ethernet and Infiniband.
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NEitan Rabin <rabin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add support for direct packet access in TC, note that because
writing the packet will cause the verifier to generate a csum
fixup prologue we won't be able to offload packet writes from
TC, just yet, only the reads will work.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds ability to write packet contents using pre-validated
packet pointers (direct packet access).
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>