Add the initial clocks definitions for the s3c6400
and s3c6410. Move the epll and ext clock from the
s3c2443 support into the common code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add definitions for the s3c6400 epll and main pll
as well as functions to decode the rate. Add
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the common initialisation code for both the
S3C6400 and S3C6410, the UART registration.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the physical to virtual memory mapping and the
necessary interrupt demuxing for the PWM timer blocks.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The pwm-clock.c needs <mach/map.h> which is included
via other means on S3C24XX systems, so ensure it is
explicitly included.

Remove the includes of regs-clock.h and regs-gpio.h as
these are not needed by the build.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary support for the timer on the
S3C6400 and S3C6410 by adding <mach/tick.h>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add and initialise the two VIC (PL192) found on
the S3C64XX series CPUs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Initial support for the Samsung S3C6410 SoC.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Initialise the basic physical to virtual mappings and
then detect the CPU that the system is being run on so
that the cpu code code can call the correct initialisation
code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add IRQ definitions for the VIC0 and VIC1 interrupts
on the S3C6400 and S3C6410 SoCs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add resources and information for the UART deviecs
on the S3C64XX CPUs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary defines for <mach/uncompress.h>
to function and build an working header code block.
Signed-off-by: NBen Doioks <ben-linux@fluff.org>

Initial clock register defines.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary support for the kernel low-level
debug macros via <mach/debug-macro.S>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the include for the interrupt entry macros needed
to be included by <mach/entry-macro.S> for the kernel
interrupt handler.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the initial header files for the S3C64XX support to satisfy the
minimal requirements to build a kernel. Some definitions will therefore
be placeholders or empty functions that will ensure that the system can
build and have base functionality. These will be filled in at a later
date.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the initial PLAT_S3C64XX support files
and directory structure.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Split the timer pending code out to a seperate per-machine
header so that when compiling for mach-s3c2410 or mach-s3c24a0
we can use the right timer code without having to #ifdef the
timer driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Initial architecture support for the S3C24A0 ARCH_S3C24A0.

We don't yet add an kconfig entry in the main arch/arm/Kconfig
file as the series is not complete, so that is left until enough
support is in to be useful.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Split the map.h definitions into common S3C24XX code by
adding arch/arm/plat-s3c24xx/include/plat/map.h and
altering the machine specific header for the S3C24A0.

As we add a new <plat/map.h> we move the original one
in arch/arm/plat-s3c include directory to be called
map-base.h to distinguish the two files.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add serial support for S3C24A0, based on current S3C2410
UART driver. It adds necessary new defines in regs-serial.h
for S3C24A0 and the code to support this device in
drivers/serial/s3c24a0.c
Signed-off-by: NSandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary debug macros for the S3C24A0 to enable
kernel debugging, and fix a bug with selecting the wrong
default debug implementation from the base include.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The definition of S3C24XX_VA_GPIO used S3C2410_PA_GPIO
where it should have read S3C24XX_PA_GPIO.
Signed-off-by: NSandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add initial arch/arm/mach-s3c24a0/include/mach header
files for supporting Samsung S3C24A0 SoC.
Signed-off-by: NSandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The pwm-scaler0 and pwm-scaler1 clocks have their
.id field set to -1 as they are not referenced to
any specific device. However, parts of the pwm-clock
code used the .id field to identify which scaler
clock was being used.

Fix the problem by comparing against the pointer to
the clock to identify the scalers.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the set_rate and round_rate methods for the pwm-scaler
clock for use with the time code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

All the s3c24xx gpiolib chips share the same get/set
calls and all but one bank shares the same calls for
.direction_input and .direction_output methods.

Change the initialisation process to use an new call
to register the chips that fills in any blank calls
with the default values to avoid having to fill them
in the structure initialisers.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add a simple check when registering a clock on whether
the clock has already been added to the list.

Any attempt to re-register a clock will cause the
clock list to be come looped and thus produces silent
failures when looking up clocks.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move pwm-clock.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the core clock registration and definitions
in arch/arm/plat-s3c24xx/clock.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move time.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add a common include file (regs-irqtype.h) for the IRQ
trigger control register values S3C2410_EXTINT*.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move clock.h, cpu.h and devs.h to plat-s3c for use
with the s3c64xx support.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Update the clock settings on resume for suspend/resume
support so that if the boot loader changes anything or
the system's PLL is reset then we return with the correct
settings.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We cannot sleep if we have cpufreq pm enabled during some
of the clock operations, so change to use a spinlock to
protect the clock system.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for CPU frequency scalling to the S3C24XX serial
driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the PLL calculation code into it's own header
file for re-use with the other plat-s3c24xx based
systems such as the S3C24A0.

Note, we change the name of s3c2410_get_pll to the
more generically named s3c24xx_get_pll as well as
the related defintions.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Only certain boards need these clocks, and they are not
available on some CPUs (such as the S3C24A0) so remove
them from arch/arm/plat-s3c24xx/clock.c and into their
own file with appropriate Kconfig entries.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We need to add plat-s3c to the build to get the headers
that will go in here once moved from include/asm-arm so
we may as well put some useful common s3c code in here
to stop the errors generated form having nothing built.

The cpu setup is now passed the cpu idcode and the table
of supported cpus to s3c_init_cpu() to abstract the
cpu identification out of the initial io setup.

As well as moving the cpu initialisation code, we move the
map of the board specific items up to the calling code as
none of the map_io() functions actually do anything other
than pass this to iotable_init().

This patch does not rename any of the init functions that
will be common to s3c24xx and any other s3c architectures
as this can be done at a later date as it will touch all
the board support files which use functions such as
s3c24xx_init_clocks() and s3c24xx_init_uarts().

Note, the header arch/arm/plat-s3c24xx/include/plat/cpu.h
still has functions that are used by both the cpu and
board initialisation functions. This means that each board
has definitions specific to the cpu support included and
the vice-versa.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add a default header for <mach/io.h> for systems
such as the S3C24A0 which do not need any of the
complex code that the S3C2410 uses.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>