Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that the Buffalo-specific initvals have been
moved to a separate array, update the default high
power TX gain table for all AR9300 v2.2 devices.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Buffalo device WZR-HP-G450H uses the index 3 for TX gain,
which is set to the high_power table currently. Later variants
of the router use the same index, but instead refer to the
low_ob_db gain table. This is not handled in the driver since
there is no way to distinguish board revisions and the high_power
table is used (incorrectly) for the newer variants.

By default, devices based on AR9300 using the TX gain index 3 have
to use the high_power table. To make sure that WZR-HP-G450H is not
broken when the high_power table is updated, use a separate array
based on information obtained from the platform data.

The current situation where only the original variant of WZR-HP-G450H
works properly stays unchanged.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Update radio/baseband/gain tables.
* Mark ar9331_modes_high_power_tx_gain_1p1 as a duplicate
* ar9331_1p1_mac_postamble is not a duplicate.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable the ALWAYS_KEYSEARCH bit in the initvals. Currently
this is done in the driver, but adding this to the initvals
makes it easier to be in sync with the INI files given
by the systems engineering team.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Certain baseband registers require different values
to be programmed when operating in a DFS channel to
ensure that radar detection works correctly. This
is required for AR9300, AR9340 and AR9580.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sparse reports the following:

  CHECK   drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:570:34: warning: dubious: !x & y

There should be a parens around the expression.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable the beaconing in wnc36xx by tweaking the tim offset and
force the use of AP-style beaconing. Otherwise, beaconing is not
working. The tim offset is set to 256. Otherwise, this will
overwrite mesh beacon submitted by mac80211.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When TX data URB reaches high water mark the message
"data: -ENOSR is returned" is printed.
This is not an error case, so change it to debug print.
Signed-off-by: NUjjal Roy <royujjal@gmail.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The check for 'priv' pointer is redundant. 'priv' won't
be used later in this routine.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bridged packets are updated to statistics on both TX and RX
paths. Also fix a typo in the comment.
Signed-off-by: NUjjal Roy <royujjal@gmail.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The skb is modified in sending the TX packet. Save the original
packet length to a variable so that we can get the correct
statistics update.
Signed-off-by: NUjjal Roy <royujjal@gmail.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The skb is modified in processing the RX packet. Save the original
packet length to a variable so that we can get the correct
statistics update.
Signed-off-by: NUjjal Roy <royujjal@gmail.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX packets are handled in different paths. Not all paths have
decrement of rx_pending counter. This patch fixes the counter
imbalance.
Signed-off-by: NUjjal Roy <royujjal@gmail.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

eth_hdr is defined in kernel. Use a different variable name in
our functions.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SNAP/LLC header in the AARP packet is being stripped off while
preparing an EthernetII header.
Annex M, Table M.3 in 802.11 spec says that some header
(ex. AppleTalk AARP(2)) should pass through untouched.
This patch modifies the check to exclude/include EthernetII
header translation for special cases.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use 'rfc1042_header' available in net/wireless/util.c
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Actually we are updating snap_type with h_proto (__be16 variable)
in ethernet frame header. Hence endianness conversion is not
required.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware expects the command structure members in little
endianness.
Signed-off-by: NUjjal Roy <royujjal@gmail.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Conflicts:
	drivers/net/wireless/ath/ath10k/htc.c
	drivers/net/wireless/ath/ath10k/mac.c

Conflicts:
	drivers/net/wireless/brcm80211/Kconfig
	net/mac80211/util.c

As it stands dynamic user regulatory domain support is
only possible for a few programmed regulatory domains as
a few countries do not allow for this.

The existing code however only would take advantage of
the feature if a custom world regulatory domain is used
though as that's when we clear beconing flags. We need
to lift this restriction as otherwise this feature is
pointless.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used later.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used later.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.

@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@

-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));

Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Reported-by: NMihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While at it convert this into a switch statement, this
makes it easier and manage.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Simplify ath_reg_apply_beaconing_flags() by making use of
thew new no-ir helper.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This also applies the no-ibss flag to the channels or clears it.
The idea here is to clarify no initiated radiation should be
allowed on these channels.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The routine ath_reg_apply_active_scan_flags() can be a bit
hard to read, this cleans it up by adding helpers for the
two cases of clearing IR flags or adding them. This approach
also makes no assumptions on the index of channels 12 and 13
so it should be portable accross different drivers.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The existing logic removes the passive scan flag from
channels 12 and 13 when a regulatory hint coming from
something other than a country IE has been passed. This
is incorrect, the original intention was to ensure we
always have passive scan enabled for these two channels
for a specific set of custom world regulatory domains.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The static analyser "cppcheck" shows the following typo:
drivers/net/wireless/rtlwifi/rtl8188ee/dm.c:1081]: (style) Same expression on both sides of '!='.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Cc: Stable <stable@vger.kernel.org> [3.10+]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>